H.VIEW H.264 User manual

1
H.VIEW Hybrid CCTV Security Camera DVR
USER MANUAL
Http://www.hviewsmart.com

2
Contents
Overview.........................................................................................................................3
Installation..................................................................................................................... 4
Log in & Log out.......................................................................................................... 7
Hard drive setup...........................................................................................................8
Motion detect................................................................................................................ 9
Privacy Mask...............................................................................................................10
Email setup..................................................................................................................10
Network Status........................................................................................................... 11
Record Setting............................................................................................................12
Video Playback...........................................................................................................14
Web viewer.................................................................................................................. 15
Mobile phone / IPAD viewer....................................................................................16
CMS Viewer................................................................................................................. 18

3
Overview
Before installation
Remove the power supply module before proceeding.
Check the input voltage to the power supply module before connecting it.
Keep the product away from humidity.
Ensure that all devices connected to the product should be properly earth-grounded.
Rear Panel
4channels
8 channels
Select one from VGA/HDMI before outputting the video

4
Since the cable quality may affect directly to the video quality depending on the distance
between the camera and DVR
Installation
Connecting to an external device
This product supports 1080p 60 Hz HDMI monitors and regular monitors that support DVI and VGA
inputs. Connect an HDMI cable to the port on the product ‘s rear bottom,Or use VGA cable to
connect the product with a VGA monitor.
Once the product is set for NTSC or PAL output, connect cameras of the corresponding
Video standard for proper operations.
Power Connection
For stable operation of the product, it is recommended to use the provided adapter.
Arrange up the cables and be careful not to peel off the cable coating.
Camera and DVR recorder Connection
2Cameras system

5
4cameras system (Include 8 Channels and 4 channels)
There is Label on Video cable ,”Only for DVR” & “Only for Camera”,please choose
right port when you connect cable
1-4 Splitter be used to power camera, connect one port of 30M Video cable with 1-4
Splitter
There are 2 adapter included in package,One is used to power DVR recorder ,one is
used to connect with 1-4 splitter to power 4 cameras you received.
You must connect Internet cable with DVR,then you can remotely view via Mobile

6
Phone and PC.
8channels & 8 cameras system
If you bought 8 channels & 8 cameras system ,you will receive :
* 1 x 8CH AHD DVR
* 8 x CCTV security Cameras
* 8 x 60ft Power Video Cable
* 2 x 1-4 splitter cable
* 3 x 12V DC Power Supply
* 1 x Remote Control
* 1 x Mouse
Connect the RJ45 port in the rear panel to the router
You can connect DVR to a PC or mobile device in the same remote network and
control or manipulate it on the monitor of the PC or mobile device
All connections

7
Log in & Log out
Log in
To manipulate or access the menus of DVR, you should have logged in.
1. When the system starts, the log in
screen appears
2. Select a user and provide the
password.The default User Name is
"admin" ,password is “blank”(leave it null)
3.Click <OK>. You will access the system
Log out
To prevent unauthorized access, it is recommended to log out when you leave the screen.
1.In the monitoring screen, click
<MENU> in the bottom left corner of the
screen to <LOG OUT>.
2.While logged out, Search / Backup /
System Settings/ Record Settings / Exit
menus are restricted to use.

8
General Setup
You can set time zone,Date and language storage in this page.
1.Time zone : specify the GMT standard time for your local area.
2.System time: Set the current time and date
3.Language: specify the language of your local area
4.Storage Full: Set<Overwrite> means system will continue recording video and will
cover the former data when hard drive is full
5.Auto Logout:If you set “0” which means you don’t set up any standby time
Hard drive setup
You can set to delete the recording automatically and set the overwrite options, and
you can also format the HDD recording data.
1.From--[Main menu]--[Advanced]--[Storage]

9
2.Choose <Format Storage> before you using hard drive
Before setting hard drive you need confirm if the hard drive has been connected
successfully.
System will automatically overwritten the former data when hard drive is full ,if you
need change model of recording ,please check 【General setting】
Motion detect
Set the motion sensor of the camera so that it can detect a motion event.
1.From <Main Menu> - <Alarm> - <Motion
Detect>
2.Use the mouse to specify the use of each
option item
>Channel : Choose channel you want set motion
detect
>Enable ：turn on the motion detect
>Sensitivity: Set the sensitivity level of the
motion sensor
>Region : Specify the motion detection area.

10
>MD interval : Specify the interval of motion detect
>Record channel:Specify the channel which will record when motion be detected
>Choose suitable push approach:Show message,Send email,Buzzer,Write Log,FTP
upload,Mobile reported
The motion detection sensitivity may differ depending on the characteristics of the connected
camera or the installation environment.
Motion area setup
From the motion detect window,click<Region>in the right corner to display the area setup screen
Click <Region> to move the motion detect area setup screen
Press and hold the left mouse button and
drag to select /deselect your desired area
Right-click any area to display the popup
window as in the right picture.
While the popup window is
displayed,Left-click area to mask color the
area you want set motion detect,area with no
color is where you set.
Click any area back to interface page.
Privacy Mask
You can edit privacy mask settings and privacy masking areas for video from each camera.
Enabling Privacy Mask
From <Main menu> -- <system> -- <display> ---< region cover>
Use the mouse to set channels enabled
Click Set,you will see a black box in the monitor screen,drag box to select your desired
area..
Right-click mouse ,windows will back to previous page
To apply the change,click<OK> in the bottom of the screen
When done, click <CLOSE> in the lower screen to return to the previous menu.
Recorder
Email setup

11
You can register and test an email address so that an email notification is delivered at a specific
interval or if an event occurs.
1. From <Main Menu> - <System> - <NetService> ,Select <EMAIL>
2. Use the mouse to specify the use of email and select
>SMTP Server:Set up the mail server.
Set the mail server that will be used for
notification to the DVR.
Use the virtual keyboard to enter your mail
server.
>Port: Enter the mail server port.
>User name:Provide the email account
(ID) of the sender.
>Password : Provide the password of the
sender.
>Sender:Provide the email account of the
sender
>Receiver:Provide the email address of
>Mail Testing: Send a test email and
check if the test email is delivered normally
3. To apply the change, click <OK> in the bottom of the screen.
4. When done, click <OK> in the lower screen. The confirmation message appears and you will
return to the previous menu.
Network Status
From the network map screen, you can check the internet connection status and camera
connection status, and check also the details of the connection status for each camera.
1.Check Internet status
From <Main Menu> - <Info> - <Version>
Check Nat status of device.
<Connected>:Means Network
connection is successful
<Probing DNS>: Network
connection is lost

12
2.Network Map
>Net Card:Choose specific Net card
>IP address : Indicates the internal IP address of the DVR.
>Subnet Mask:provide the subnet mask
address(Default:255.255.255.0)
>Gateway:provide the gateway address
(Same IP address as your router IP
address)
>Primary DNS:Enter the address of the
primary DNS server
>Secondary DNS:8.8.8.8(Enter the
address of the secondary DNS server.)
>Media Port:34567
>HTTP Port:80
3.To apply the change,click <OK> in the bottom of the screen.
4.When done, click <OK> in the lower screen. The confirmation message appears and you will
return to the previous menu.
If you don’t know how to change set network of recorder ,please check
FAQ
Record Setting
Operation Mode
You can set the recording options for
Auto or Manual mode.
1. From <Main menu> -- < Record >
select <Record Conf>.
2. Set the recording options for each
selected Record mode.
3. To apply the change, click <OK> in
the bottom of the screen.
4. When done, click <OK> at the
bottom of screen. The confirmation message appears and you will return to the previous menu

13
Configuration
> Channel : Choose specific channel to record
> Length: Set the length of per video file.Default length is 60min
> PreRec:Set up the period of record
> Period: Set the period of record（Default period is 24-hours,for all channels）
> Detect: Recording will proceed only if a motion is detected(If need system record when detect
motion,you need set “Motion detection”,check “motion detect”)
Motion detect setting
Tick “Enable”
select < Sensitivity >, < Region >, < Record Channel >, < Buzzer >, < Send Email > according to
your needs and click “OK” to save.
Click set to set region, default is all choosed.
You can change the region by right click
your mouse, drag the mouse and draw the
area.

14
Video Playback
Using the play bar
Start Playback
Play backward
Stop Playing
Slow Playback
Prev/Next Frame
Prev/Next File
Repest playback
Full Screen
Start Editing
Backup
1Video Playback Region
2Video date query,color filled
represent containing video content
3Playback Channel Optional
4Video Playback time
5Playback control key
Note: Different color means
dofferent recording,motion
detection recording is red one
on bar

15
Web viewer
Connection
Open a browser and type the URL in the address bar http://www.xmeye.net
After you enter the URL and you will see the live screen
1Click the upper warning bar to install the ActiveX
2Click <Install>
NOTE:If you failed to install the
ActiveX control, move to
<Tools>---<Internet
Options>---<Security>---<Trus
t Sites>--<Add> add
http://www.xmeye.net to your
security site
Log in
There are 2 ways of log in,<By User>
& <By Device>
1.By User
Before Logging in with User
name,you need register .
1Click<Register>,at
corner of screen
2Type all information in
register page

16
2.By Device
Find device Serial number
in monitor
1Type Serial number
2Default User name:
admin
password:null(leave null)
3Click<Login and
Preview>
Mobile phone / IPAD viewer
You can use your IPAD to remotely view your device.Please so as follow:
Download “XMeye”in APP store
Open “XMeye”,you will see the picture such as bellow: Click <Local
login>
You will see the log in page,such as bellow
Click <+>at right corner of screen to add device into your APP

17
At this page ,you need type your serial number and password.
The default user name: admin
Password: null (leave it blank,don’t type any words)
There is no need to enter device name and http port
After doing as above,you can see your device
You can choose specific CAM to view your device
After click channel click”Start Preview”
Now you will see video .Hope it can helps.

18
CMS Viewer
Install
Running disc (Included in package),open
“CMS”and install it.
Open the “CMS” client .
1Click”System” at the right corner of
screen
2Click”Device Manager”
3Click “zoom list”,then click “ADD
AERA”
At this page,you need type data of zone and up
zone
1You can enter any words you like,such
as “111”
2When you finished,click”OK”
Now you need add your device into
“CMS”
1Click “zone”(You edited at step 2)
2Click “ADD DEVICE”

19
At this page,you need type some data of your
device
1Choose Cloud
2Type serial number of recorder
3Click”OK”
Choose specific CAM and view it
1Click “Test”
2Choose CAM you want view
Congratulations.