H3C FAN-80B-1-B User manual

2
1
H3C FAN-80B-1-B Fan Tray User Guide-APW100
H3C FAN-80B-1-B 风扇手册-APW100
Overview 风扇模块介绍
Views 风扇模块示意图
Fan tray specifications 风扇模块规格
1
2
The FAN-80B-1-B fan tray provides port side-intake and power module-side exhaust airflow and
delivers high cooling efficiency. It is small, hot swappable, and can automatically adjust the fan speed
according to the device temperature.
风扇模块为抽风风扇（风扇从端口侧向电源侧抽风）。该风扇模块具有体积小、散热快、可热插拔的
特点，还可根据设备温度自动进行风速调整，能为设备提供强劲的散热降温功能。
Specification 规格Item 项目
Max power consumption 最大功耗
Voltage 工作电压
Operating temperature 工作环境温度
Operating humidity 工作环境相对湿度
Storage temperature 存放环境温度
Storage humidity 存放环境相对湿度
102 W
12 V
0°C to 45°C (32°F to 113°F)
0°C～45°C
5% to 95% (non-condensing)
5%～95% RH, 无冷凝
–40°C to +70°C (–40°F to +158°F)
-40°C～70°C
5% to 95% (non-condensing)
5%～95% RH, 无冷凝
Alarm LED of the fan tray 风扇模块告警指示灯
Description 含义Status 指示灯状态
Steady red 红色常亮
The fan tray is operating correctly.
风扇模块运行正常
A problem has occurred on the fan tray.
风扇模块运行异常
Steady green 绿色常亮
Installing or removing the fan tray 风扇模块的安装和拆卸
BOM: 3101A0RF
Off 灭The fan tray is not installed securely or no
power is present.风扇模块未插好或未供电
FAN-80B-1-B
Handle
把手
Alarm LED
告警指示灯
Alignment hole
对位标记
Specification 规格Item 项目
Dimensions (including the handle) (H × W × D)
外形尺寸（含把手）
Airflow direction 风道方向
84 × 81 × 240 mm (3.31 × 3.19 × 9.45 in)
84 × 81 × 240 mm（高*宽*深）
From the port side to the power module side
风扇从端口侧向电源侧抽风
Safety precautions 安全注意事项
1
Wear an ESD wrist strap when installing or removing the fan tray. Make sure the wrist strap has
good skin contact and is reliably grounded.
在安装和拆卸风扇模块时，操作者需自行准备并佩戴防静电腕带，请确保防静电腕带已经正确接地
并与皮肤良好接触。
Do not touch any bare wire or terminal on the fan tray.
请不要接触风扇模块中露出的任何导线、端子部分。
Do not place the fan tray in a damp environment and prevent liquid from flowing into the fan tray.
请不要将风扇模块放置在潮湿的地方，也不要让液体进入风扇模块内部。
When an internal circuit or component is faulty, contact H3C Support. Do not remove any
components from the fan tray yourself. 当风扇模块内部线路或元器件出现故障时，请移交维修人员
进行检修，不要随意拆卸风扇模块上的部件。
!
Max fan speed 最大风扇转速
Max airflow 最大风量
12800 R.P.M
12800 R.P.M（转/分钟）
130 CFM
130 CFM（立方英尺/分钟）

3
Copyright © 2019, New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
Copyright © 2019 新华三技术有限公司 版权所有，保留一切权利
本文档中的信息如有更改，恕不另行通知
如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com
Installing the fan tray 风扇模块的安装
2Before you install the fan tray, make sure the fan tray model is compatible with the device and the
airflow direction is as required at the installation site. 在安装风扇模块前，请确认风扇模块型号与设备
匹配且风扇模块的风道方向和安装环境的通风方向要求一致。
To avoid damaging the fan tray and the backplane connectors of the device, insert the fan tray slowly.
If you encounter a resistance or the fan tray tilts, remove the fan tray and reinsert it. 为了避免损坏风
扇模块或背板的连接器端子，风扇模块插入过程中动作要缓慢，如果插入过程阻力较大或风扇模块位
置出现偏斜，必须先拔出风扇模块，然后重新插入。
You can install the fan tray with the adapter facing upwards or downwards. Whether to install the fan
tray with the adapter facing upwards or downwards depends on the device mode. The fan tray and
the fan tray slot each have an alignment hole. Orient the fan tray as indicated by alignment holes.
Ensure that the alignment hole in the fan tray is aligned with that in the device after the fan tray
installation. 风扇模块支持正向安装和反向安装两种安装方式。正向安装时风扇连接器在下，反向安装
时风扇连接器在上。不同机型支持的安装方式不同，您可以使用风扇模块的对位标记判断设备的安装
方式。安装完成后风扇模块的对位标记应该和设备上的对位标记水平对齐。
!
Removing a fan tray 风扇模块的拆卸
3
Ensure electricity safety when you remove a fan tray on an operating device.
在设备运行状态下更换风扇模块时，请注意用电安全。
Never touch a rotating fan on an operating device.
在设备运行状态下更换风扇模块时，请不要接触转动中的风扇，避免被旋转中的风扇划伤.
To prevent an unbalanced fan from causing loud noise, do not touch the fan, even if It is not rotating.
在风扇停止转动后，建议不要碰触风扇扇叶和旋转轴，以免损害风扇的动平衡，导致风扇运转时噪音
加大。
Place the removed fan tray on an anti-static mat or in an anti-static bag.
请将拆卸下来的风扇模块及时放置到防静电垫子上或防静电袋中。
!
①Press the red part of the handle with one hand and pull the fan tray partway out ofthe slot.
用一只手握紧风扇模块的把手红色部分，将风扇模块拉出来一部分。
②Supporting the fan tray bottom with the other hand, pull the fan tray completely out of the slot
along the guide rails. 用另一只手托住风扇模块底部，同时沿着插槽导轨水平缓慢地向外拉出
风扇模块。
The installation procedure is similar with the fan tray adapter facing upwards and downwards. The
following installs the fan tray on an S9820-8C switch with the adapter facing upwards.
Orient the fan tray with the adapter facing upwards. Holding the fan tray handle with one hand and
supporting the fan tray bottom with the other, insert the fan tray slowly into the slot along the guide
rails. Make sure the fan tray has good contact with the backplane connectors. If the alignmenthole
inthefantrayisalignedwiththatinthedevice,thefantrayisinstalledcorrectly.
正向安装和反向安装的安装方法相似，本文以风扇模块反向安装到S9820-8C设备为例进行介绍。
将风扇连接器朝上，用一只手捏住风扇模块把手，另一只手托住风扇模块底部，将风扇模块沿着插槽
导轨水平插入，直到风扇模块完全进入插槽，并且与背板连接器端子接触良好。此时风扇模块和机箱
上的对位标记水平对齐，表示风扇模块安装正确。
12
3
Removing a fan tray
拆卸风扇模块
2
1
Install the fan tray with the adapter facing upwards
风扇模块反向安装（风扇连接器在上）
Installing the fan tray 风扇模块的安装
2