H3C LSXM102XFAN User manual

The fan tray is hot swappable. Follow these guidelines when you replace the fan tray
on an operating switch:
Ensure electrical safety.
Replace a fan tray only when the other fan tray is operating correctly.
To prevent dust from entering the chassis, keep the failed fan tray in position before
the replacement.
When you hot-swap a fan tray, the remaining fan tray automatically increases the fan
rotation speed and makes louder noise. Take protection measures such as wearing
an earmuff or earplug. In addition, make good preparation before hot swapping a fan
tray to minimize the operation time.
风扇框支持热插拔，在设备运行状态下进行风扇框的更换时，需要注意的是：
请注意用电安全；
只有在保证一个风扇框正常运行的情况下，才可以插拔另一个风扇框；
建议在新风扇框到位后再启动更换操作，在此之前请将旧风扇框保留在机框中，避免
灰尘进入设备；
在设备运行状态下插拔风扇框时，设备处于单风扇框工作状态，智能调速风扇会自动
增加转速，可能会造成噪音增大。请做好防护措施（如佩戴降噪耳罩、耳塞等劳保设
施），并事先做好准备工作尽可能缩短操作时间。
Long-time exposure to strong air flow might cause discomfort. To avoid this hazard, do
not stand close to the air outlet vents when the switch is operating. If you must be next
to the switch on the air outlet vent side for an extended period, avoid the air flow or
take other protective measures.
H3C建议您不要在设备运行时长时间停留在设备出风口侧，以免强风引起身体不适。在
设备出风口侧操作设备时，请尽量避开强风，或者做好相应防护。
1
Overview 风扇框的介绍 !
2
BOM: 3101A0KB
H3C LSXM102XFAN Fan Tray User Manual-6PW103
H3C LSXM102XFAN 风扇框 用户手册-6PW103
The LSXM102XFAN fan tray contains one fan and provides a maximum airflow of 170 cubic
feet per minute (CFM). The fan tray draws ambient air into the chassis through the air vents
in the MPU and LPU panels and exhausts the air carrying heat through the air vents in the
fan tray.
LSXM102XFAN 风扇框内有1个风扇，能够提供的最大风量为170 CFM（立方英尺/分钟）。
该风扇框采用抽风设计，冷风由前面板主控板区和业务板区通风孔进入，携带运行产生的热
量，从风扇框通风孔排出。
Fan side view 风扇侧外观
Panel side view 面板侧外观
Captive screw 松不脱螺钉
Fan 风扇
Captive screw 松不脱螺钉
Fan tray status LED
风扇框状态指示灯
Handle pivot
风扇框把手转轴
Handle 风扇框把手
Tools required 准备工具
Phillips screwdriver 十字螺丝刀ESD wrist strap 防静电腕带

4
3
To install the fan tray in slot FAN1, orient the fan tray so that the LEDs are on the left
side of the front panel. To install the fan tray slot FAN2, orient the fan tray so that the
LEDs are on the right side of the front panel.
将风扇框安装到FAN1槽位和FAN2槽位时，安装方向不同。插入FAN1槽位时，请将风
扇框上指示灯部分朝向左侧，插入FAN2槽位时，请将风扇框上指示灯部分朝向右侧。
Installing the fan tray 风扇框的安装
!
The following procedure uses the S12502X-AF switch as an example to describe fan
tray installation. 如下以风扇框安装到S12502X-AF交换机为例，将风扇框安装到其他交
换机的过程和要求与此例类似，不再赘述。
The S12502X-AF switch has two fan tray slots: FAN1 and FAN2. Install two fan trays
on the switch. S12502X-AF交换机上有FAN1和FAN2两个风扇框槽位，在设备运行过程中，
请安装两个风扇框。
1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.
佩戴防静电腕带，确保防静电腕与皮肤良好接触，并确认防静电腕带已经良好接地。
2. Remove the filler panel in the target fan tray slot. Keep the removed filler panel for future use.
拆除交换机上的风扇框槽位假面板。
3. Unpack the fan tray. 将风扇框从包装袋中取出。
4. Orient the fan tray correctly and align the fan tray with the fan tray slot.
确定安装方向，安装FAN1槽位风扇框时将指示灯部分朝向左侧，安装FAN2槽位风扇框时将
指示灯部分朝向右侧。
5. Hold the fan tray handle and insert the fan tray fully into the slot. Keep the fan tray as
straight and steady as possible when inserting it into the slot.
紧握把手，将风扇框完全插入机箱中，插入时尽量保持平稳。
6. Fasten the captive screws on the fan tray .
使用螺丝刀拧紧风扇框上的松不脱螺钉以固定风扇框。
Removing the filler panel
拆卸风扇框槽位假面板
Orient the fan tray with the LEDs on the right for slot FAN2
安装FAN2槽位风扇框时指示灯朝向右侧
Orient the fan tray with the LEDs on the left for slot FAN1
安装FAN1槽位风扇框时指示灯朝向左侧
3
1
2
1

5
Removing the fan tray 风扇框的拆卸
When you remove the fan tray, do not touch the rotating fans to avoid getting injured.
风扇框更换时，请不要接触转动中的风扇，以免受到伤害。
1. Prepare an anti-static mat. 准备一个防静电垫子，用于放置拆卸下来的风扇框。
2. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.
佩戴防静电腕带确保防静电腕带与皮肤良好接触，并确认防静电腕带已经良好接地。
3. Loosen the captive screws on the fan tray. 使用螺丝刀松开风扇框上的松不脱螺钉。
4. Hold the fan tray handle and pull the fan tray outward until the fan tray is disengaged from
the chassis. Remove the fan tray after the fans stop rotating.
握住风扇框上的把手，将风扇框缓慢拉出机箱一些，使风扇框与设备脱离连接，待风扇停转
后，再将风扇框完全取出。
5. Place the fan tray on the anti-static mat. 将风扇框放置到防静电垫子上。
!
Copyright © 2018, New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
Copyright © 2018 新华三技术有限公司 版权所有，保留一切权利
本文档中的信息如有更改，恕不另行通知
如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com
4
4
1
1