H3C S1016 User manual

H3C S1016/1024 Ethernet Switch
User Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-UM-20080418-1.05

Copyright © 2004-2008, Hangzhou H3C Technologies Co.,
Ltd.
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form
or by any means without prior written consent of Hangzhou H3C
Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care, , TOP G, , IRF,
NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,
Comware, Secware, Storware, NQA, VVG, V2G, VnG, PSPT, XGbus,
N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou
H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners.
CE
This equipment complies with the following European Directives:
89/336/EEC (electromagnetic compatibility), 73/23/EEC (low voltage).
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of
any kind, express or implied.
To obtain the latest information, please access:
http://www.h3c.com

Technical Support
[e-mail]
http://www.h3c.com

About This Manual
Organization
This document is organized as follows:
Chapter Content
Chapter1 Product
Overview This chapter describes the appearance and features of this product.
Chapter2 Switch
Installation This chapter describes the precautions and steps to install this product.
Conventions
The manual uses the following conventions:
Symbols
I.
Convention Description
Caution
Means reader be careful. Improper
operation may cause data loss or damage
to equipment.
Note Means a complementary description.
Environmental Protection

This product has been designed to comply with the requirements on
environmental protection. For the proper storage, use and disposal of
this product, national laws and regulations must be observed.

User Manual
H3C S1016/1024 Ethernet Switch Table of Contents
i
Table of Contents
Chapter 1 Product Overview ........................................................1-1
1.1 Introduction ........................................................................1-1
1.2 Product Specifications .......................................................1-1
1.3 Hardware Description ........................................................1-3
1.3.1 Product Appearance................................................1-3
1.3.2 LEDs........................................................................1-5
Chapter 2 Switch Installation .......................................................2-1
2.1 Installation Preparations ....................................................2-1
2.1.1 Security Tips............................................................2-1
2.1.2 Installation Environment..........................................2-2
2.1.3 Electromagnetic Environment .................................2-2
2.2 Installing the Switch...........................................................2-3
2.2.1 Sticking Feet............................................................2-3
2.2.2 Connecting Power Cord..........................................2-3
2.2.3 Examining the Installation .......................................2-4

User Manual
H3C S1016/1024 Ethernet Switch Chapter 1 Product Overvie
w
1-1
Chapter 1 Product Overview
1.1 Introduction
H3C S1016/1024 Ethernet Switch is a management-free product
at desktop level. It offers wire-speed Layer 2 switching immediately
after the product is powered on without any configuration.
The S1016 provides 16 autosensing 10/100Base-TX ports and
the S1024 provides 24 autosensing 10/100Base-TX ports.
1.2 Product Specifications
Table 1-1 Specifications of S1016/1024
Item Description
Physical dimensions
(H ×W ×D )
S1016: 44 ×266 ×162 mm (1.7 ×10.5 ×6.4
in.)
S1024: 44 ×330 ×230 mm (1.7 ×13.0 ×9.1
in.)
Weight S1016: 1.5 kg (3.3 lb)
S1024: 2 kg (4.4 lb)
Port
S1016:
16 autosensing 10/100Base-TX Ethernet
ports
S1024:
24 autosensing 10/100Base-TX Ethernet
ports

User Manual
H3C S1016/1024 Ethernet Switch Chapter 1 Product Overvie
w
1-2
Item Description
Port attribute
RJ-45 connector
Compliant with IEEE 802.3 and IEEE
802.3u
10/100 Mbps transmission rate
Half duplex, full duplex, and
auto-negotiation
Auto-MDI/MDI-X
Cable
10Base-T:
Category-3/-4/-5 twisted pair cable with
maximum transmission distance 100 m
(328.1 ft.)
100Base-TX:
Category-5 twisted pair cable with
maximum transmission distance 100 m
(328.1 ft.)
Input voltage 100 VAC to 240 VAC, 50/60 Hz
Power consumption S1016: 6 W
S1024: 9 W
Operating
temperature 0°C to 40°C (32°F to 104°F)
Storage temperature –10°C to +70°C (14°F to 158°F)
Operating humidity
(noncondensing) 20% to 85%
Storage humidity
(noncondensing) 10% to 90%
System cooling Air cooling

User Manual
H3C S1016/1024 Ethernet Switch Chapter 1 Product Overvie
w
1-3
Table 1-2 Features of S1016/1024
Features Description
Wire-speed Layer 2
switching All ports support wire-speed forwarding.
All ports are in the same broadcast domain.
Switching mode Store and forward
MAC address table Address auto-learning and auto-aging (with
aging time 300 seconds)
Maximum MAC address entries: 8K
1.3 Hardware Description
1.3.1 Product Appearance
I. Front panel
The power LED, port LEDs and 16/24 (S1016/1024)
10/100Base-TX Ethernet ports are arranged in order on the front
panel of the S1016/1024, as shown in Figure 1-1 and Figure 1-2
respectively.
Figure 1-1 Front view of S1016

User Manual er 1 Product Overvie
H3C S1016/1024 Ethernet Switch Chapt
w
1-4
Figure 1-2 Front view of S1024
II. Rear panel
The S1016 has an AC power socket and a grounding pole on its
rear panel as shown below:
Figure 1-3 Rear view of S1016
The S1024 has an AC power socket and a grounding pole on its
rear panel as shown below:
Figure 1-4 Rear view of S1024