H3C s5800 series User manual

H3C S5800 Series Ethernet Switches
Quick Start
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6PW109-20140516

Copyright © 2009-2014, Hangzhou H3C Technologies Co., Ltd. and its
licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by
any means without prior written consent of Hangzhou H3C Technologies Co.,
Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, ,
IRF, NetPilot, Netflow, SecEngine, SecPath, SecCenter, SecBlade, Comware,
ITCMM and HUASAN are trademarks of Hangzhou H3C Technologies Co.,
Ltd.
All other trademarks that may be mentioned in this manual are the property of
their respective owners
Notice
The information in this document is subject to change without notice. Every
effort has been made in the preparation of this document to ensure accuracy
of the contents, but all statements, information, and recommendations in this
document do not constitute the warranty of any kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental protection
requirements. The storage, use, and disposal of this product must meet the
applicable national laws and regulations.

Preface
H3C S5800 Series Ethernet Switches Quick Start describes the installation of
the H3C S5800 series Ethernet switches.
This preface includes:
•Audience
•Conventions
•Obtaining documentation
•Technical support
•Documentation feedback
Audience
This documentation is intended for:
•Network planners
•Field technical support and servicing engineers
•Network administrators working with the S5800 series
Conventions
This section describes the conventions used in this documentation set.
Convention Descri
p
tion
WARNING An alert that calls attention to important information that if not
understood or followed can result in personal injury.
CAUTION
An alert that calls attention to important information that if not
understood or followed can result in data loss, data
corruption, or damage to hardware or software.
IMPORTANT An alert that calls attention to essential information.
NOTE An alert that contains additional or supplementary
information.

Convention Descri
p
tion
TIP An alert that provides helpful information.
Obtaining documentation
Access the most up-to-date H3C product documentation on the World Wide
Web at http://www.h3c.com.
Click the links on the top navigation bar to obtain different categories of
product documentation:
[Technical Support & Documents > Technical Documents]—Provides
hardware installation, software upgrading, and software feature
configuration and maintenance documentation.
[Products & Solutions]—Provides information about products and
technologies, as well as solutions.
[Technical Support & Documents > Software Download]—Provides the
documentation released with the software version.
Technical support
servi[email protected]
http://www.h3c.com
Documentation feedback
You can e-mail your comments about product documentation to
[e-mail].
We appreciate your comments.

i
Contents
Overview···········································································································1
About this guide ······························································································· 1
Product overview······························································································ 1
Installation preparations···················································································2
Installation site·································································································· 2
Installation tools································································································ 2
Installing the switch···························································································3
Installation flow ································································································ 3
Installing the switch in a rack ········································································· 4
Attaching an ESD wrist strap ································································· 4
Installation accessories ··········································································· 4
Mounting positions·················································································· 5
Installing an S5800-54S switch in a 19-inch rack ······························ 6
Installing an S5800-60C-PWR switch in a 19-inch rack ···················· 9
Installing the other S5800 switch models in a 19-inch rack ············11
Mounting the switch on a workbench··························································12
Connecting the grounding cable··································································13
Installing fan trays··························································································15
Installing power modules···············································································17
Connecting the power cord ··········································································21
Connecting an AC power cord ···························································21
Connecting the DC power cord···························································23
Installing an interface card ···········································································26
Installing an OAP card··················································································27
Installing a PoE module ·················································································28

1
Overview
About this guide
This guide describes the basic installation procedures for the S5800 Switch
Series. For more information about the installation and configuration
procedures, system description, appearance, LEDs, software loading and
upgrading, and troubleshooting, see H3C S5800 Switch Series Installation
Guide.
Product overview
The H3C S5800 Switch Series includes the following models:
•S5800-56C
•S5800-56C-PWR
•S5800-32C
•S5800-32C-PWR
•S5800-32F
•S5800-60C-PWR
•S5800-54S
NOTE:
The H3C S5800 Switch Series models and installation procedures might
be updated without prior notice. For the latest quick start guide, go
to http://www.h3c.com.

2
Installation preparations
Installation site
The switch must be used indoors. Before installation, verify that the rack is
sturdy enough to support the switch and its accessories.
To ensure correct operation and long service life of your switch, install it in an
environment that meets the temperature, humidity, and electromagnetic shield
(EMS) requirements. For more information, see H3C S5800 Switch Series
Installation Guide.
Installation tools
The installation tools are not provided with the switch. Prepare them yourself.
Figure 1 Installation tools
(1) ESD wrist strap (2)
Flat-blade screwdriver
(3) Phillips screwdriver (4) Marker
(5) Wrench (6)
Blow dryer

3
Installing the switch
Installation flow
Figure 2 Installation flow
Connect the grounding cable
Install the switch to a
specified position
Start
Connect the power cord
Verify the installation
Power on the switch
Select and install power modules
Hot swappable power
modules are used?
Yes
No
Correctly operating? Power off the switch
Troubleshoot the switch
No
Yes
Install hot swappable
components?
Install a PoE module
Install an interface cardInstall an OAP card
Select hot swappable
components
Yes
Correctly operating? Troubleshoot the switch
Verify the installation
Yes
No
End
No
Hot swappable fan
trays are used?
Select and install
fan trays
Yes
No
Fan trays have
been installed?
No
Yes

4
Installing the switch in a rack
Attaching an ESD wrist strap
Before installation, wear an ESD strap, and make sure one end of the wrist
strap has a good skin contact and the other end is attached to a post of the
correctly-grounded rack, as shown in Figure 3.
Figure 3 Attaching an ESD wrist strap
Installation accessories
All switch models except the S5800-60C-PWR switch come with a pair of 1 U
mounting brackets. The S5800-60C-PWR switch comes with a pair of 2 U
mounting brackets, and each mounting bracket is attached with a cable
management bracket.
Figure 4 Mounting brackets
(1) 1 U mountin
g
brackets
(2) 2 U mountin
g
brackets
and cable mana
g
ement brackets

5
In addition to a pair of 1 U mounting brackets, the S5800-54S switch also
comes with a pair of chassis rails and a pair of slide rails.
Figure 5 Chassis rail and slide rail
(1) Chassis rail (2) Slide rail
Mounting positions
All switch models except the S5800-54S switch provide three mounting
positions: one front mounting position (near the network ports), one
mid-mounting position, and one rear mounting position (near the power
modules). Figure 6 shows the mounting positions on these switches.
Figure 6 Mounting positions
(1) Front mounting position
(2) Mid-mountin
g
position
(3) Rear mountin
g
position
The S5800-54S switch provides two mounting positions: one front mounting
position (near the network ports) and one rear mounting position (near the
power modules), as shown in Figure 7.