H3C S5130S-EI series Owner's manual

H3C S5130S-EI Switch Series
Hardware Information and Specifications
New H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6W109-20221015

Copyright © 2022, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written
consent of New H3C Technologies Co., Ltd.
Trademarks
Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this
document are the property of their respective owners.
Notice
The information in this document is subject to change without notice. All contents in this document, including
statements, information, and recommendations, are believed to be accurate, but they are presented without
warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions
contained herein.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage, use,
and disposal of this product must meet the applicable national laws and regulations.

Preface
H3C S5130S-EI Switch Series Hardware Information and Specifications describes product models,
technical specifications, ports,and LEDs of the S5130S-EI switches.
This preface includes the following topics about the documentation:
•
Audience.
•
Conventions.
•
Documentation feedback.
Audience
This documentation is intended for:
•
Network planners.
•
Field technical support and servicing engineers.
•
Network administrators working with the switches.
Conventions
The following information describes the conventions used in the documentation.
Command conventions
Convention
Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... }
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ]
Square brackets enclose a set of optional syntax choices separated by vertical bars,
from which you select one or none.
{ x | y | ... } *
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select a minimum of one.
[ x | y | ... ] *
Asterisk marked square brackets enclose optional syntaxchoices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign
can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.
GUI conventions
Convention
Description
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window opens; click OK.
> Multi-level menus are separated by angle brackets. For example, File > Create >
Folder.

Symbols
Convention
Description
WARNING! An alert that calls attention to important information that if not understood or followed
can result in personal injury.
CAUTION:
An alert that calls attention to important information that if not understood or followed
can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT:
An alert that calls attention to essential information.
NOTE:
An alert that contains additional or supplementary information.
TIP:
An alert that provides helpful information.
Network topology icons
Convention
Description
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that
supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access
controller engine on a unified wired-WLAN switch.
Represents an access point.
Represents a wireless terminator unit.
Represents a wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security
gateway, or load balancing device.
Represents a security module, such as a firewall, load balancing, NetStream, SSL
VPN, IPS, or ACG module.
Examples provided in this document
Examples in this document might use devices that differ from your device in hardware model,
configuration, or software version. It is normal that the port numbers, sample output, screenshots,
and other information in the examples differ from what you have on your device.
T
T
T
T

Documentation feedback
You can e-mail your comments about product documentation to [e-mail].
We appreciate your comments.

i
Contents
1 Product models and technical specifications············································1-3
Product models···············································································································································1-3
Technical specifications··································································································································1-5
Non-PoE switch models··························································································································1-5
PoE switch models································································································································1-12
2 Chassis views························································································2-21
S5130S-10P-EI·············································································································································2-21
S5130S-12TP-EI···········································································································································2-21
S5130S-20P-EI·············································································································································2-22
S5130S-28P-EI/S5130S-28P-EI-M···············································································································2-23
S5130S-28TP-EI···········································································································································2-23
S5130S-52P-EI/S5130S-52P-EI-M···············································································································2-24
S5130S-52TP-EI···········································································································································2-25
S5130S-28S-EI/S5130S-28S-EI-M···············································································································2-25
S5130S-28S-EI-DP·······································································································································2-26
S5130S-52S-EI/S5130S-52S-EI-M···············································································································2-27
S5130S-28F-EI ·············································································································································2-27
S5130S-52F-EI ·············································································································································2-28
S5130S-28MP-EI··········································································································································2-29
S5130S-52MP-EI··········································································································································2-30
S5130S-28PS-EI···········································································································································2-30
S5130S-28ST-EI···········································································································································2-31
S5130S-52ST-EI···········································································································································2-32
S5130S-10P-HPWR-EI·································································································································2-32
S5130S-12TP-HPWR-EI·······························································································································2-33
S5130S-20P-PWR-EI····································································································································2-34
S5130S-28P-PWR-EI····································································································································2-34
S5130S-28P-HPWR-EI·································································································································2-35
S5130S-52P-PWR-EI····································································································································2-36
S5130S-16S-PWR-EI····································································································································2-37
S5130S-16S-UPWR-EI-Q·····························································································································2-37
S5130S-28S-PWR-EI····································································································································2-38
S5130S-28S-HPWR-EI·································································································································2-39
S5130S-28S-HPWR-EI-Q·····························································································································2-40
S5130S-28S-UPWR-EI-Q·····························································································································2-40
S5130S-52S-PWR-EI····································································································································2-41
S5130S-28MP-HPWR-EI······························································································································2-42
S5130S-10MS-UPWR-EI······························································································································2-42
S5130S-28ST-PWR-EI·································································································································2-43
S5130S-52ST-PWR-EI·································································································································2-44
S5130S-52P-PWR-EI-AC·····························································································································2-45
S5130S-52S-PWR-EI-AC·····························································································································2-45
S5130S-28P-HPWR-EI-AC···························································································································2-46
S5130S-28S-HPWR-EI-AC···························································································································2-47
3 Removable components········································································3-48
4 Ports and LEDs······················································································4-49
Ports······························································································································································4-49
Console port··········································································································································4-49
Management Ethernet port ···················································································································4-50
10/100/1000BASE-T autosensing Ethernet port···················································································4-50
5G/2.5G/1000BASE-T autosensing Ethernet port ················································································4-50
2.5G/1000/100BASE-T autosensing Ethernet port···············································································4-51
10/5/2.5/1GBASE-T autosensing Ethernet port····················································································4-51
SFP port················································································································································4-52

ii
SFP+ port··············································································································································4-57
Combo interface····································································································································4-59
LEDs ·····························································································································································4-60
System status LED································································································································4-60
Management Ethernet port LED ···········································································································4-60
Power supply status LED······················································································································4-60
RPS status LED····································································································································4-61
Mode LED (MODE)·······························································································································4-61
SFP/SFP+ port LED······························································································································4-61
Ethernet port LEDs································································································································4-61

1-3
1 Product models and technical
specifications
Product models
This document is applicable to the S5130S-EI switch series. Table1-1 describes the S5130S-EI
switch series models.
Table1-1 S5130S-EI switch series models
Model Product code (PID)
Non-PoE switch models
S5130S-10P-EI LS-5130S-10P-EI LS-5130S-10P-EI-GL
LS-5130S-10P-EI-H1
S5130S-12TP-EI LS-5130S-12TP-EI LS-5130S-12TP-EI-GL
LS-5130S-12TP-EI-H1
S5130S-20P-EI LS-5130S-20P-EI LS-5130S-20P-EI-GL
LS-5130S-20P-EI-H1
S5130S-28P-EI
LS-5130S-28P-EI
LS-5130S-28P-EI-GL
LS-5130S-28P-EI-H1
LS-5130S-28P-EI-H1-GL
S5130S-28P-EI-M LS-5130S-28P-EI-M
S5130S-28TP-EI LS-5130S-28TP-EI
LS-5130S-28TP-EI-GL
S5130S-52P-EI
LS-5130S-52P-EI
LS-5130S-52P-EI-GL
LS-5130S-52P-EI-H1
LS-5130S-52P-EI-H1-GL
S5130S-52P-EI-M LS-5130S-52P-EI-M
S5130S-52TP-EI LS-5130S-52TP-EI
LS-5130S-52TP-EI-GL
S5130S-28S-EI
LS-5130S-28S-EI
LS-5130S-28S-EI-GL
LS-5130S-28S-EI-H1
LS-5130S-28S-EI-H1-GL
S5130S-28S-EI-M LS-5130S-28S-EI-M
S5130S-28S-EI-DP LS-5130S-28S-EI-DP

1-4
Model Product code (PID)
S5130S-52S-EI
LS-5130S-52S-EI
LS-5130S-52S-EI-GL
LS-5130S-52S-EI-H1
LS-5130S-52S-EI-H1-GL
S5130S-52S-EI-M LS-5130S-52S-EI-M
S5130S-28F-EI LS-5130S-28F-EI
LS-5130S-28F-EI-GL
S5130S-52F-EI LS-5130S-52F-EI
LS-5130S-52F-EI-GL
S5130S-28MP-EI LS-5130S-28MP-EI
LS-5130S-28MP-EI-GL
S5130S-52MP-EI LS-5130S-52MP-EI
LS-5130S-52MP-EI-GL
S5130S-28PS-EI LS-5130S-28PS-EI
LS-5130S-28PS-EI-GL
S5130S-28ST-EI LS-5130S-28ST-EI
LS-5130S-28ST-EI-GL
S5130S-52ST-EI LS-5130S-52ST-EI
LS-5130S-52ST-EI-GL
PoE switch models
S5130S-10P-HPWR-EI LS-5130S-10P-HPWR-EI LS-5130S-10P-HPWR-EI-GL
LS-5130S-10P-HPWR-EI-H1
S5130S-12TP-HPWR-EI LS-5130S-12TP-HPWR-EI LS-5130S-12TP-HPWR-EI-GL
LS-5130S-12TP-HPWR-EI-H1
S5130S-20P-PWR-EI LS-5130S-20P-PWR-EI LS-5130S-20P-PWR-EI-GL
LS-5130S-20P-PWR-EI-H1
S5130S-28P-PWR-EI LS-5130S-28P-PWR-EI LS-5130S-28P-PWR-EI-GL
LS-5130S-28P-PWR-EI-H1
S5130S-28P-HPWR-EI LS-5130S-28P-HPWR-EI
LS-5130S-28P-HPWR-EI-GL
S5130S-52P-PWR-EI LS-5130S-52P-PWR-EI
LS-5130S-52P-PWR-EI-GL
S5130S-16S-PWR-EI LS-5130S-16S-PWR-EI
LS-5130S-16S-PWR-EI-GL
S5130S-16S-UPWR-EI-Q LS-5130S-16S-UPWR-EI-Q
S5130S-28S-PWR-EI LS-5130S-28S-PWR-EI
LS-5130S-28S-PWR-EI-GL

1-5
Model Product code (PID)
LS-5130S-28S-PWR-EI-H1
S5130S-28S-HPWR-EI LS-5130S-28S-HPWR-EI
LS-5130S-28S-HPWR-EI-GL
S5130S-28S-HPWR-EI-Q LS-5130S-28S-HPWR-EI-Q
S5130S-28S-UPWR-EI-Q LS-5130S-28S-UPWR-EI-Q
S5130S-52S-PWR-EI LS-5130S-52S-PWR-EI
LS-5130S-52S-PWR-EI-GL
S5130S-52P-PWR-EI-AC LS-5130S-52P-PWR-EI-AC
LS-5130S-52P-PWR-EI-AC-GL
S5130S-52S-PWR-EI-AC LS-5130S-52S-PWR-EI-AC
LS-5130S-52S-PWR-EI-AC-GL
S5130S-28P-HPWR-EI-AC LS-5130S-28P-HPWR-EI-AC
LS-5130S-28P-HPWR-EI-AC-GL
S5130S-28S-HPWR-EI-AC LS-5130S-28S-HPWR-EI-AC
LS-5130S-28S-HPWR-EI-AC-GL
S5130S-28MP-HPWR-EI LS-5130S-28MP-HPWR-EI
LS-5130S-28MP-HPWR-EI-GL
S5130S-10MS-UPWR-EI LS-5130S-10MS-UPWR-EI
LS-5130S-10MS-UPWR-EI-GL
S5130S-28ST-PWR-EI LS-5130S-28ST-PWR-EI
LS-5130S-28ST-PWR-EI-GL
S5130S-52ST-PWR-EI LS-5130S-52ST-PWR-EI
LS-5130S-52ST-PWR-EI-GL
NOTE:
Switches of the
same model but different PIDs might differ in hardware and software features.
You
can view the PID of a switch on the label located on its rear panel or top panel.
Technical specifications
Non-PoE switch models
Table1-2 Technical specifications for non-PoE switch models (1)
Item S5130S-10P-EI S5130S-12TP-EI S5130S-20P-EI
Dimensions (H ×
W × D) 43.6 × 266 × 161 mm (1.72 × 10.47 × 6.34 in) 43.6 × 266 × 161 mm (1.72 × 10.47 × 6.34 in) 43.6 × 330 × 230 mm (1.72 × 12.99 × 9.06 in)
Weight ≤ 1.5 kg (3.31 lb) ≤ 1.5 kg (3.31 lb) ≤ 2 kg (4.41 lb)
Console port 1 × serial console port 1 × serial console port 1 × serial console port
10/100/1000BAS
E-T autosensing 8 10 (The two highest-numbered
10/100/1000BASE-T
autosensing Ethernet ports
16

1-6
Item S5130S-10P-EI S5130S-12TP-EI S5130S-20P-EI
Ethernet port
form combo interfaces with
their corresponding SFP ports,
respectively.)
SFP port 2
4 (The two lowest-numbered
SFP ports form combo
interfaces with their
corresponding
10/100/1000BASE-T
autosensing Ethernet ports,
respectively.)
4
Input voltage •Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz
Minimum power
consumption 7 W 8 W 9 W
Maximum power
consumption 12 W 15 W 19 W
Chassis leakage
current
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Melting current of
power supply fuse 2 A/250 V 2 A/250 V 2 A/250 V
Cooling system Passive cooling Passive cooling Passive cooling
Operating
temperature –5°C to +45°C (23°F to 113°F)
Operating
humidity 5% to 95%, noncondensing
Fire resistance
compliance UL 62368-1/EN62368-1/IEC62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Table1-3 Technical specifications for non-PoE switch models (2)
Item S5130S-28P-EI
S5130S-28P-EI-M S5130S-52P-EI S5130S-52P-EI-M
Dimensions (H × W
× D) 43.6 × 440 × 160 mm (1.72 × 17.32 × 6.30 in) 43.6 × 440 × 230 mm (1.72 × 17.32 × 9.06 in)
Weight ≤2.5 kg (5.51 lb) ≤3.5 kg (7.72 lb)
Console port 1 × serial console port 1 × serial console port
10/100/1000BASE-
T autosensing
Ethernet port 24 48
SFP port 4 4
Input voltage •Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz
Minimum power
consumption 9 W 18 W
Maximum power
consumption 23 W 41 W
Chassis leakage
UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC

1-7
Item S5130S-28P-EI
S5130S-28P-EI-M S5130S-52P-EI S5130S-52P-EI-M
current compliance
60950-1/GB4943.1
Melting current of
power supply fuse 2 A/250 V 3.15 A/250 V
Cooling system Passive cooling Using fixed fan trays to draw ambient air in from the left side and right side and exhaust
heated air from the power supply side.
Operating
temperature –5°C to +45°C (23°F to 113°F)
Operating humidity 5% to 95%, noncondensing
Fire resistance
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Table1-4 Technical specifications for non-PoE switch models (3)
Item S5130S-28TP-EI S5130S-52TP-EI S5130S-28S-EI
S5130S-28S-EI-M S5130S-52S-EI S5130S-52S-EI-M
Dimensions
(H × W × D)
43.6 × 440 × 160
mm (1.72 × 17.32 ×
6.30 in)
43.6 × 440 × 260
mm (1.72 × 17.32 ×
10.24 in)
43.6 × 440 × 160
mm (1.72 × 17.32 ×
6.30 in)
43.6 × 440 × 230 mm
(1.72 × 17.32 × 9.06
in)
Weight ≤2 kg (4.41 lb) ≤3.5 kg (7.72 lb) ≤2.5 kg (5.51 lb) ≤3.5 kg (7.72 lb)
Console port
•1 × serial
console port
•1 × micro USB
console port
When both ports are
connected, only the
micro USB console
port is available.
•1 × serial
console port
•1 × micro USB
console port
When both ports are
connected, only the
micro USB console
port is available.
•1 × serial
console port
•1 × micro USB
console port
When both ports are
connected, only the
micro USB console
port is available.
•1 × serial
console port
•1 × micro USB
console port
When both ports are
connected, only the
micro USB console
port is available.
10/100/1000
BASE-T
autosensing
Ethernet
port
26 (The two
highest-numbered
10/100/1000BASE-
T autosensing
Ethernet ports form
combo interfaces
with their
corresponding SFP
ports, respectively.)
50 (The two
highest-numbered
10/100/1000BASE-
T autosensing
Ethernet ports form
combo interfaces
with their
corresponding SFP
ports, respectively.)
24 48
SFP port
4 (The two
lowest-numbered
SFP ports form
combo interfaces
with their
corresponding
10/100/1000BASE-
T autosensing
Ethernet ports,
respectively.)
4 (The two
lowest-numbered
SFP ports form
combo interfaces
with their
corresponding
10/100/1000BASE-
T autosensing
Ethernet ports,
respectively.)
N/A N/A
SFP+ port N/A N/A 4 4
Input voltage •Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz

1-8
Item S5130S-28TP-EI S5130S-52TP-EI S5130S-28S-EI
S5130S-28S-EI-M S5130S-52S-EI S5130S-52S-EI-M
Minimum
power
consumption 10 W 20 W 10 W 19 W
Maximum
power
consumption 24 W 42 W 24 W 44 W
Chassis
leakage
current
compliance
UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Melting
current of
power
supply fuse
2 A/250 V 3.15 A/250 V 2 A/250 V 3.15 A/250 V
Cooling
system Passive cooling
Using fixed fan trays
to draw ambient air
in from the left side
and right side of the
chassis and exhaust
heated air out from
the power supply
side.
•Models with
product codes
LS-5130S-28S
- EI-H1 and
LS-5130S-28S
-EI-H1-GL:
Passive
cooling.
•Other models:
Using fixed fan
trays to draw
ambient air in
from the left
side, right side,
and port side of
the chassis and
exhaust heated
air out from the
power supply
side.
Using fixed fan trays
to draw ambient air in
from the left side and
right side and exhaust
heated air out from
the power supply side.
Operating
temperature –5°C to +45°C (23°F to 113°F)
Operating
humidity 5% to 95%, noncondensing
Fire
resistance
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Table1-5 Technical specifications for non-PoE switch models (4)
Item S5130S-28F-EI S5130S-52F-EI
Dimensions (H × W × D) 43.6 × 440 × 360 mm (1.72 × 17.32 ×
14.17 in) 43.6 × 440 × 360 mm (1.72 × 17.32 × 14.17 in)
Weight ≤6 kg (13.23 lb) ≤6.5 kg (14.33 lb)
Console port
•1 × serial console port
•1 × micro USB console port
When both ports are connected, only
the micro USB console port is
•1 × serial console port
•1 × micro USB console port
When both ports are connected, only the
micro USB console port is available.

1-9
Item S5130S-28F-EI S5130S-52F-EI
available.
10/100/1000BASE-T
autosensing Ethernet
port
8 (Each and its corresponding SFP
port form a combo interface.) 2 (Each and its corresponding SFP port form a combo interface.)
SFP port
24 (The eight highest-numbered
SFP ports form combo interfaces
with their corresponding
10/100/1000BASE-T autosensing
Ethernet ports, respectively.)
48 (The two highest-numbered SFP
ports form combo interfaces with their
corresponding 10/100/1000BASE-T
autosensing Ethernet ports,
respectively.)
SFP+ port 4 4
Power supply slot 2, at the rear panel 2, at the rear panel
Input voltage
CA-70A12:
•Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz
•Max voltage: 90 VAC to 290 VAC @ 47 to 63 Hz
PSR75-12A:
•Rated voltage:
100 VAC to 240 VAC @ 50 or 60 Hz
240 VDC
•Max voltage:
90 VAC to 290 VAC @ 47 to 63 Hz
180 to 320 VDC
PSR150-A1:
•Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz
PSR150-D1:
•Rated voltage: –48 VDC to –60 VDC
•Max voltage: –36 VDC to –72 VDC
DC power source for the PSR150-D1 power supply: –48 VDC power source in
the equipment room or an RPS (H3C RPS800-A or RPS1600-A)
Minimum power
consumption
•1 × CA-70A12: 15 W
•2 × CA-70A12: 17 W
•1 × PSR75-12A: 15 W
•2 × PSR75-12A: 17 W
•1 × PSR150-A1: 18 W
•1 × PSR150-D1: 18 W
•2 × PSR150-A1: 23 W
•2 × PSR150-D1: 22 W
•1 × CA-70A12: 26 W
•2 × CA-70A12 29 W
•1 × PSR75-12A: 26 W
•2 × PSR75-12A: 29 W
•1 × PSR150-A1: 27 W
•1 × PSR150-D1: 27 W
•2 × PSR150-A1: 32 W
•2 × PSR150-D1: 33 W
Maximum power
consumption
•1 × CA-70A12: 45 W
•2 × CA-70A12: 48 W
•1 × PSR75-12A: 45 W
•2 × PSR75-12A: 48 W
•1 × PSR150-A1: 48 W
•1 × PSR150-D1: 51 W
•2 × PSR150-A1: 55 W
•2 × PSR150-D1: 57 W
•1 × CA-70A12: 69 W
•2 × CA-70A12: 72 W
•1 × PSR75-12A: 69 W
•2 × PSR75-12A: 72 W
•1 × PSR150-A1: 74 W
•1 × PSR150-D1: 84 W
•2 × PSR150-A1: 95 W
•2 × PSR150-D1: 95 W
Chassis leakage current
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Melting current of power
supply fuse
•CA-70A12: 10 A/250 V
•PSR75-12A: 3.15 A/250 V

1-10
Item S5130S-28F-EI S5130S-52F-EI
•PSR150-A1: 6.3 A/250 V
•PSR150-D1: 8 A/250 V
Cooling system Using fixed fan trays to draw ambient air in from the left side and port side and
exhaust heated air from the right side.
Operating temperature –5°C to +45°C (23°F to 113°F)
Operating humidity 5% to 95%, noncondensing
Fire resistance
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Table1-6 Technical specifications for non-PoE switch models (5)
Item S5130S-28MP-EI S5130S-52MP-EI
Dimensions (H × W × D) 43.6 × 440 ×160 mm (1.72 × 17.32 ×
6.30 in) 43.6 × 440 × 230 mm (1.72 × 17.32 × 9.06 in)
Weight ≤2.5 kg (5.51 lb) ≤3.5 kg (7.72 lb)
Console port
•1 × serial console port
•1 × micro USB console port
When both ports are connected, only the micro USB console port is available.
10/100/1000BASE-T
autosensing Ethernet
port 24 48
5G/2.5G/1000BASE-T
autosensing Ethernet
port 2
SFP port 2
AC-input voltage •Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz
Minimum power
consumption 14 W 22 W
Maximum power
consumption 28 W 46 W
Chassis leakage current
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Melting current of power
supply fuse 3.15 A/250 V 6.3 A/250 V
Cooling system Using fixed fan trays to draw ambient air in from the left side of the chassis and
exhaust heated air out from the power supply side.
Operating temperature –5°C to +45°C (23°F to 113°F)
Operating humidity 5% to 95%, noncondensing
Fire resistance
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1

1-11
Table1-7 Technical specifications for non-PoE switch models (6)
Item S5130S-28S-EI-DP S5130S-28ST-
EI S5130S-52ST-EI S5130S-28PS-
EI
Dimensions (H
× W × D)
43.6 × 440 × 260 mm
(1.72 × 17.32 × 10.24
in)
43.6 × 440 ×160
mm (1.72 × 17.32
× 6.30 in)
43.6 × 440 × 260 mm
(1.72 × 17.32 × 10.24
in)
43.6 × 440 × 360
mm (1.72 × 17.32
× 14.17 in)
Weight ≤3.5 kg (7.72 lb) ≤2.5 kg (5.51 lb) ≤4 kg (8.82 lb) ≤4.5 kg (9.92 lb)
Console port
•1 × serial console
port
•1 × micro USB
console port
When both ports are
connected, only the
micro USB console
port is available.
1 × serial console port
10/100/1000B
ASE-T
autosensing
Ethernet port
24 24 48
24 (The eight
highest-numbere
d
10/100/1000BAS
E-T autosensing
Ethernet ports
form combo
interfaces with
their
corresponding
SFP ports,
respectively.)
10/5/2.5/1GBA
SE-T
autosensing
Ethernet port
N/A 2 2 N/A
SFP port N/A N/A N/A
8 (The eight SFP
ports form combo
interfaces with
their
corresponding
10/100/1000BAS
E-T autosensing
Ethernet ports,
respectively.)
SFP+ port 4 2 2 4
Input voltage
AC power source:
•Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz
DC power source (supported only by the S5130S-28PS-EI switch):
•Rated voltage:–24 VDC to –48 VDC
•Max voltage: –24 VDC to –48 VDC
Minimum
power
consumption
Single AC input: 11 W
Dual AC inputs: 15 W AC: 14 W AC: 22 W AC: 12 W DC: 11 W
Maximum
power
consumption
Single AC input: 25 W
Dual AC inputs: 26 W AC: 36 W AC: 53 W AC: 31 W DC: 26 W

1-12
Item S5130S-28S-EI-DP S5130S-28ST-
EI S5130S-52ST-EI S5130S-28PS-
EI
Chassis
leakage current
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Melting current
of power
supply fuse 2 A/250 V 2 A/250 V 2 A/250 V 2 A/250 V
Cooling system
Using fixed fan trays to draw ambient air in from the chassis left side and exhaust heated
air from the chassis right side.
Operating
temperature –5°C to +45°C (23°F to 113°F)
Operating
humidity 5% to 95%, noncondensing
Fire resistance
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
PoE switch models
Table1-8 Technical specifications for PoE switch models (1)
Item S5130S-10P-HPWR-EI S5130S-12TP-HPWR-EI S5130S-20P-PWR-EI
Dimensions (H × W
× D) 43.6 × 330 × 230 mm (1.72 × 12.99 × 9.06 in) 43.6 × 330 × 230 mm (1.72 × 12.99 × 9.06 in) 43.6 × 330 × 230 mm (1.72 × 12.99 × 9.06 in)
Weight ≤3 kg (6.61 lb) ≤3 kg (6.61 lb) ≤3 kg (6.61 lb)
Console port 1 × serial console port 1 × serial console port 1 × serial console port
10/100/1000BASE-
T autosensing
Ethernet port 8
10 (The two
highest-numbered
10/100/1000BASE-T
autosensing Ethernet ports
form combo interfaces with
their corresponding SFP
ports, respectively.)
16
SFP port 2
4 (The two lowest-numbered
SFP ports form combo
interfaces with their
corresponding
10/100/1000BASE-T
autosensing Ethernet ports,
respectively.)
4
Input voltage •Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz
Maximum PoE
power per port 30 W
30 W
The combo copper ports on
an S5130S-12TP-HPWR-EI
switch do not support PoE
power supply.
30 W
Total PoE power 125 W 125 W
Models with product
code
LS-5130S-20P-PWR-EI
: 170 W

1-13
Item S5130S-10P-HPWR-EI S5130S-12TP-HPWR-EI S5130S-20P-PWR-EI
Models with product
code
LS-5130S-20P-PWR-EI
-H1: 185 W
Minimum power
consumption 13 W 14 W
Models with product
code
LS-5130S-20P-PWR-EI
: 18 W
Models with product
code
LS-5130S-20P-PWR-EI
-H1: 15 W
Maximum power
consumption
(including PoE
power
consumption)
153 W 156 W
Models with product
code
LS-5130S-20P-PWR-EI
: 210 W
Models with product
code
LS-5130S-20P-PWR-EI
-H1: 235 W
Chassis leakage
current compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Melting current of
power supply fuse 6.3 A/250 V 6.3 A/250 V 10 A/250 V
Cooling system Passive cooling Passive cooling
Using fixed fan trays to
draw ambient air in from
the left side and exhaust
heated air from the right
side.
Operating
temperature –5°C to +45°C (23°F to 113°F)
Operating humidity 5% to 95%, noncondensing
Fire resistance
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Table1-9 Technical specifications for PoE switch models (2)
Item S5130S-28ST-PWR-EI S5130S-52ST-PWR-EI
Dimensions (H × W ×
D) 43.6 × 440 × 320 mm (1.72 × 17.32 × 12.60 in) 43.6 × 440 × 320 mm (1.72 × 17.32 × 12.60 in)
Weight ≤4.5 kg (9.92 lb) ≤4.5 kg (9.92 lb)
Console port 1 × serial console port
10/100/1000BASE-T
autosensing Ethernet
port 24 48
10/5/2.5/1GBASE-T
autosensing Ethernet
port 2
SFP+ port 2
Input voltage •Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz

1-14
Item S5130S-28ST-PWR-EI S5130S-52ST-PWR-EI
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz
Maximum PoE power
per port 30 W
Total PoE power 370 W
Minimum power
consumption 20 W 32 W
Maximum power
consumption
(including PoE power
consumption)
450 W 470 W
Chassis leakage
current compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Melting current of
power supply fuse 2 A/250 V
Cooling system Using fixed fan trays to draw ambient air in from the chassis left side and exhaust
heated air from the chassis right side.
Operating
temperature –5°C to +45°C (23°F to 113°F)
Operating humidity 5% to 95%, noncondensing
Fire resistance
compliance UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Table1-10 Technical specifications for PoE switch models (2)
Item S5130S-28P-P
WR-EI S5130S-52P- PWR-EI S5130S-28P- HPWR-EI S5130S-28P- HPWR-EI-AC S5130S-52P- PWR-EI-AC
Dimensions
(H × W × D)
43.6 × 440 × 260
mm (1.72 ×
17.32 ×10.24 in)
43.6 × 440 ×
400 mm (1.72 ×
17.32 × 15.75
in)
43.6 × 440 ×
260 mm (1.72 ×
17.32 × 10.24
in)
43.6 × 440 × 260
mm (1.72 ×
17.32 × 10.24 in)
43.6 × 440 ×
400 mm (1.72
× 17.32 ×
15.75 in)
Weight ≤4 kg (8.82 lb) ≤6 kg (13.23 lb) ≤4.5 kg (9.92
lb) ≤4.5 kg (9.92 lb) ≤6 kg (13.23
lb)
Console port 1 × serial console port
10/100/1000
BASE-T
autosensing
Ethernet
port
24 48
28 (The four
highest-numbe
red
10/100/1000B
ASE-T
autosensing
Ethernet ports
each form
combo
interfaces with
its
corresponding
SFP port.)
28 (The four
highest-number
ed
10/100/1000BA
SE-T
autosensing
Ethernet ports
each form a
combo interface
with its
corresponding
SFP port.)
48
SFP port 4 4
4 (Each and its
corresponding
10/100/1000B
ASE-T
autosensing
4 (Each and its
corresponding
10/100/1000BA
SE-T
autosensing
4

1-15
Ethernet port
form a combo
interface.)
Ethernet port
form a combo
interface.)
Input
voltage
•Rated
voltage:
100 VAC to
240 VAC @
50 or 60 Hz
•Max
voltage: 90
VAC to 264
VAC @ 47
to 63 Hz
AC power source:
•Rated voltage: 100 VAC to 240 VAC @ 50 or 60
Hz
•Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz
DC power source: H3C RPS1600-A
•Rated voltage: –54 VDC to –57 VDC
•Max voltage:
Single DC input: –44 VDC to –60 VDC
AC and DC inputs: –54 VDC to –57 VDC
•Rated
voltage:
100 VAC
to 240
VAC @
50 or 60
Hz
•Max
voltage:
90 VAC to
264 VAC
@ 47 to
63 Hz
Maximum
PoE power
per port
30 W
The combo copper ports on the S5130S-28P-HPWR-EI and S5130S-28P-HPWR-EI-AC
switches do not support PoE power output.
Total PoE
power
•Models with
product
code
LS-5130S-
28P-PWR-
EI-H1: 240
W
•Other
models:
170 W
•AC: 370 W
•DC: 740 W AC: 370 W
DC: 740 W 370 W 370 W
Minimum
power
consumptio
n
•Models with
product
code
LS-5130S-
28P-PWR-
EI-H1: 15
W
•Other
models: 19
W
•AC: 36 W
•DC: 26 W AC: 23 W
DC: 16 W 15 W 36 W
Maximum
power
consumptio
n (including
PoE power
consumptio
n)
•Models with
product
code
LS-5130S-
28P-PWR-
EI-H1: 295
W
•Other
models:
230 W
•AC: 467 W
•DC: 807 W AC: 446 W
DC: 790 W 443 W 467 W
Chassis
leakage
current
compliance
UL 62368-1/EN 62368-1/IEC 62368-1/UL 60950-1/EN 60950-1/IEC 60950-1/GB4943.1
Melting
current of
power
supply fuse
10 A/250 V 15 A/250 V 15 A/250 V 15 A/250 V 15 A/250 V
Cooling Using fixed fan
trays to draw
Using fixed fan
trays to draw
Using fixed fan
trays to draw
Using fixed fan
trays to draw
Using fixed fan
trays to draw