H3C S6850-56HF Operating and maintenance manual

2
1
Installation accessories 安装附件介绍
Wear an ESD wrist strap, and make sure the wrist strap makes good skin contact and is reliably grounded.
操作者需佩戴防静电腕带，确保防静电腕带与皮肤良好接触，并确认防静电腕带已经良好接地。
No installation tools are provided with the switch. Prepare them yourself as required.
交换机不随机提供安装工具，请用户根据实际安装需求自己准备安装工具。
Phillips screwdriver
十字螺丝刀
ESD wrist strap
防静电腕带
Tool list 工具参考
!
Marker
记号笔
Grounding cable and
grounding screw
接地线和接地螺钉
Removable cable tie
可拆卸式扎带
Mounting bracket
挂耳
Short chassis rail and
long slide rail
长滑道和短导轨
M4 screw
M4螺钉
M6 screw and cage nut
(user supplied)
M6 螺钉和浮动螺母（用户自备）
Long chassis rail and short
slide rail (optional)
短滑道和长导轨（选配）
Attaching the accessories to the switch 安装附件到交换机
The device provides multiple installation positions for chassis rails on two sides. Determine the
installation position for the chassis rails based on the rack depth.
设备侧面板提供了多个滑道导轨安装位，用户可根据机柜的深度，调整滑道导轨的安装位置。
The installation positions of the accessories in the following figure are for illustration only. Determine
installation positions for the accessories based on the installation requirement.
以下图中附件的安装位置仅供参考，请根据实际安装场景的需要选择合适的安装位置。
If the rack depth is in the range of 692 to 853 mm (27.24 to 33.58 in), use the short chassis rails and
long slide rails provided with the switch for installation. For device stability, make sure the slide rails
reach a minimum of 20 mm (0.79 in) out of chassis rails.
如果机柜前后方孔条间距在692～853mm范围内，请使用标配的长滑道短导轨配合安装。为保证设备安
装后的稳定性，当滑道与滑道导轨安装完成后，请确保滑道的头部露出滑道导轨的最小长度为20mm。
Installing the mounting brackets and long slide rails 挂耳与长滑道配合安装
Mounting brackets installed near the port side 挂耳安装到靠近端口侧
ab
Mounting brackets installed near the power module side 挂耳安装到靠近电源侧
cd
c
1
Install the chassis rails at a or b. 挂耳安装在靠近端口侧时，滑道导轨可安装在a或b任意一处。
Install the chassis rails at c or d. 挂耳安装在靠近电源侧时，滑道导轨可安装在c或d任意一处。
Power module filler panel
电源假面板
a
H3C S6850-56HF Switch Installation Quick Start-6W101
H3C S6850-56HF交换机 快速安装指南-6W101

4
3
Connect the grounding cable to a grounding point before installing the switch in the rack.
为了防止机箱安装到机柜后无法安装接地线，请先将接地线安装到交换机侧面的接地点上。
The switch provides a grounding sign at the primary grounding point but not at the auxiliary
grounding point.
交换机主接地点标有接地标识，备用接地点上无接地标识。
The grounding screws provided with the switch are applicable to both the primary and auxiliary
grounding points.
交换机随机附带的接地螺钉同时适用于主接地点和备用接地点。
Before installing cage nuts, mark their installation positions on rack posts.
安装浮动螺母前，建议用户先使用记号笔在机柜方孔条上标注浮动螺母安装位置。
Installing the switch in a 19-inch rack 安装交换机到19英寸机柜
Install cage nuts and slide rails 安装浮动螺母与滑道
1
If the rack depth is in the range of 401 to 692 mm (15.79 to 27.24 in), purchase long chassis rails and
short slide rails yourself for installation. You need to install the long chassis rails as follows based on
the rack depth:
Not reaching out of the chassis for a rack with the depth in the range of 401 to 498 mm
(15.79 to 19.61 in).
Not reaching out or reaching out of the chassis for a rack with a depth in the range of 499 To
565 mm (19.66 to 22.24 in).
Reaching out of the chassis for a rack with the depth in the range of 566 to 692 mm
(22.28 to 27.24 in).
如果机柜前后方孔条间距在401～692mm范围内，请使用选配的短滑道长导轨配合安装。因短滑道配
套的长导轨有正装（导轨不会超出设备）和反装（导轨会超出设备）之分，用户可以根据机柜方孔条
之间的距离灵活选择安装方式。
当机柜前后方孔条间距在401～498mm范围内，请使用长导轨正装方式安装。
当机柜前后方孔条间距在499～565mm范围内，长导轨正装和反装都可以。
当机柜前后方孔条间距在566～692mm范围内，请使用长导轨反装方式安装。
For device stability, make sure the slide rails slide a minimum length of 90 mm (3.54) into the chassis
rails when rack-mounting the switch.
为保证设备安装后的稳定性，当滑道与滑道导轨安装完成后，请确保滑道的头部进入滑道导轨的最小
深度为90mm。
cd
正装（chassis rail not reaching out
of the chassis）
反装（chassis rail reaching out of
the chassis）
ab
正装（chassis rail not
reaching out of the chassis）
反装（chassis rail reaching
out of the chassis）
Installing the mounting brackets and short slide rails 挂耳与短滑道配合安装
2
Mounting brackets installed near the port side 挂耳安装在靠近端口侧
Mounting brackets installed near the power module side 挂耳安装在靠近电源侧
Install the chassis rails at c or d. The chassis rails can be installed reaching out of the chassis or not
reaching out of the chassis.
挂耳安装在靠近电源侧时，滑道导轨可安装在c或d任意一处，可采用正装方式，也可采用反装方式。
Install the chassis rails at a or b. The chassis rails can be installed reaching out of the chassis or
not reaching out of the chassis. 挂耳安装在靠近端口侧时，滑道导轨可安装在a或b任意一处，可采
用正装方式，也可采用反装方式。
The installation procedure is the same for using long and short chassis rails. The following procedure
uses the short chassis rails as an example.
采用长滑道短导轨安装交换机到机柜与采用短滑道长导轨安装交换机到机柜的方式相同，本文以采用
长滑道短导轨安装交换机到机柜为例。
a
a
d
d

6
5
Mount the switch in the rack (port side at the front) 安装交换机到机柜（以端口侧朝外为例）
The switch has a front-rear air aisle. It can provide airflow from the power module side to the port
side, or from the port side to the power module side, depending on the fan trays installed.
交换机采用前后风道设计，通过配置不同的风扇模块，可提供“电源侧到端口侧”和“端口侧到电源
侧”两种通风走向，满足不同环境下的散热要求。
Airflow direction of the switch 交换机的风向设计
Using the LSWM1FANSA fan tray
采用LSWM1FANSA风扇模块 Using the LSWM1FANSAB fan tray 采用LSWM1FANSAB 风扇模块
Installing and removing a fan tray 风扇模块的安装与拆卸
Install a fan tray 安装风扇 Remove a fan tray 拆卸风扇
11
2
The LSWM1FANSA fan tray provides power module-side intake and port-side exhaust airflow, and
its handle is blue. The LSWM1FANSAB fan tray provides port-side intake and power module-side
exhaust airflow, and its handle is red.
LSWM1FANSA为吹风风扇，风向为电源侧进风，端口侧出风，风扇把手为蓝色；
LSWM1FANSAB为抽风风扇，风向为端口侧进风，电源侧出风，风扇把手为红色。
Before installing a fan tray, make sure the airflow direction marked on the fan tray meets the
ventilation requirement of the installation site.
安装风扇模块前，请根据风扇模块的风向指示，确认气流方向和安装环境的通风要求一致。
Make sure the "TOP" mark stays on top when you install the fan tray.
安装风扇模块时，请确保“TOP”丝印朝上。
The switch comes with the five fan tray slots empty. You must install five fan trays of the same model
for the switch.
交换机出厂时5个风扇插槽均为空，用户需安装5个相同型号的风扇模块。
Make sure each slot has a module or a filler panel installed while the switch is operating.
交换机运行过程中，必须确保所有可插拔模块插槽不能为空，请务必安装相应的模块或假面板。
Do not remove multiple fan trays simultaneously. You can remove another fan tray only after you
finish replacing one fan tray. Make sure you finish replacing a fan tray within 3 minutes.
更换风扇模块过程中禁止同时拔出多个风扇模块，应按照拔出一个立即更换一个的方式进行，且
单个风扇模块的更换时间不要超过3分钟。
2
Connect the other end of the grounding cable to the grounding point on the rack.
接地线另一端连接到机柜接地点
Attach cage nuts to rack posts.
安装浮动螺母到机柜方孔条上
Attach slide rails to rack posts.
安装滑道到机柜
1
2
1
2
2

7
Install a power module 安装电源模块 Remove a power module 拆卸电源模块
12
Use a removable cable tie to secure the power cord. The method for securing AC and DC power
cords are the same. The figure uses an AC power cord as an example.
使用可拆卸式扎带固定电源线，以防止电源线脱落。直流电源线和交流电源线的固定方式相同，此
处以交流电源线为例介绍电源线的固定过程。
Copyright © 2018, New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
Copyright © 2018 新华三技术有限公司 版权所有，保留一切权利
本文档中的信息如有更改，恕不另行通知
如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com
If you are not to install a power module in a power module slot, install a filler panel in the slot. The
filler panel prevents dust from entering the chassis and ensures good ventilation.
若电源模块插槽没有安装电源模块，请及时安装假面板，防止灰尘进入交换机，同时又保证设备的良
好通风散热。
Installing and removing a power module 电源模块的安装与拆卸
Remove a filler panel 拆卸假面板
Install a filler panel 安装假面板
Connect a DC power cord 连接直流电源线 Connect an AC power cord 连接交流电源线
Before connecting a power cord, connect the grounding cable to the switch and make sure the
switch is reliably grounded.
在连接电源线前，需先连接保护地线，保证交换机正确接地。
To avoid bodily injury, connect a power cord to the switch first and then to the power source.
连接电源线时，请先完成电源线与交换机侧的连接，再进行电源线与供电系统的连接，以免造成人
身伤害。
!
Connecting a power cord 连接电源线