H3C S9500 Series Installation instructions

H3C S9500 Series Routing Switches
Command Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08194H-20080520-C-2.03
Product Version: S9500-CMW520-R2132

Copyright © 2007-2008, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care, , TOP G, , IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and
HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their
respective owners.
Notice
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.
To obtain the latest information, please access:
http://www.h3c.com
Technical Support
[e-mail]
http://www.h3c.com

About This Manual
Related Documentation
In addition to this manual, each H3C S9500 Series Routing Switches documentation
set includes the following:
Manual Description
H3C S9500 Series Routing
Switches Installation Manual
It introduces the installation procedure,
commissioning, maintenance and monitoring of
the S9500 series routing switches.
H3C S9500 Series Routing
Switches Operation Manual
It includes Product Overview, Access Volume,
IP Service Volume, IP Routing Volume, IP
Multicast Volume, MPLS VPN Volume, QoS
ACL Volume, Security Volume, System
Volume , OAA Volume and Acronyms.
Organization
H3C Command Manual is organized as follows:
Part Contents
00 Feature List and
Command Index includes Feature List and Command Index.
01 Access Volume
includes Ethernet Interface Commands, POS Interface
Commands, GVRP Commands, Link Aggregation
Commands, Port Mirroring Commands, RPR Commands,
Ethernet OAM Commands, MSTP Commands, VLAN
Commands, QinQ Commands, BPDU Tunneling
Commands, and Port Isolation Commands.
02 IP Services
Volume
includes ARP Commands, DHCP Commands, DNS
Commands, IP Addressing Commands, IP Performance
Commands, UDP Helper Commands, IPv6 Basics
Commands, Dual Stack Commands, Tunneling
Commands, and Adjacency Table Command.
03 IP Routing Volume
includes IP Routing Table Display Commands, BGP
Commands, IS-IS Commands, OSPF Commands, RIP
Commands, Routing Policy Commands, Static Routing
Commands, IPv6 BGP Commands, IPv6 IS-IS
Commands, IPv6 OSPFv3 Commands, IPv6 RIPng
Commands, and IPv6 Static Routing Commands.

Part Contents
04 IP Multicast
Volume
includes Multicast Routing and Forwarding Commands,
IGMP Snooping Commands, IGMP Commands, PIM
Commands, MSDP Commands, IPv6 Multicast Routing,
and Forwarding Commands, MLD Snooping Commands,
MLD Commands, IPv6 PIM Commands, Multicast VLAN
Commands.
05 MPLS VPN
Volume
includes MPLS Basics Commands, MPLS TE Commands,
VPLS Commands, MPLS L2VPN Commands, MPLS
L3VPN Commands, MPLS Hybrid Insertion Commands,
and GRE Commands.
06 QoS ACL Volume includes QoS Commands and ACL Commands.
07 Security Volume
includes 802.1x Commands, AAA, RADIUS HWTACACS
Commands, MAC Authentication Commands, L3+NAT
Commands, Password Control Commands, SSH2.0
Commands, and Portal Commands.
08 System Volume
includes GR Commands, VRRP Commands, HA
Commands, Device Management Commands, NQA
Commands, NetStream Commands, NTP Commands,
RMON Commands, SNMP Commands, File System
Management Commands, System Maintaining and
Debugging Commands, Basic System Configuration
Commands, Information Center Commands, User
Interface Commands, MAC Address Table Management
Commands, PoE Commands, and Clock Monitoring
Commands.
09 OAA Volume includes OAP Module Commands and ACSEI Commands.
10 Unsupported
Commands List of Unsupported Commands.
Conventions
The manual uses the following conventions:
I. Command conventions
Convention Description
Boldface The keywords of a command line are in Boldface.
italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by
vertical bars. One is selected.

Convention Description
[ x | y | ... ]
Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can be
selected.
[ x | y | ... ] *
Optional alternative items are grouped in square brackets
and separated by vertical bars. Many or none can be
selected.
&<1-n> The argument(s) before the ampersand (&) sign can be
entered 1 to n times.
# A line starting with the # sign is comments.
II. GUI conventions
Convention Description
< > Button names are inside angle brackets. For example, click
<OK>.
[ ] Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.
/ Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].
III. Symbols
Convention Description
Warning Means reader be extremely careful. Improper operation
may cause bodily injury.
Caution Means reader be careful. Improper operation may cause
data loss or damage to equipment.
Note Means a complementary description.

Command Manual
H3C S9500 Series Routing Switches OAA Volume Organization
Manual Version
T2-08194H-20080530-C-2.03
Product Version
S9500-CMW520-R2132
Organization
The OAA Volume is organized as follows:
Features (command
manual) Description
OAP Module Introduces the commands for OAP module configuration.
ACSEI Introduces the commands for ACSEI configuration.

Command Manual – OAP Module
H3C S9500 Series Routing Switches Table of Contents
i
Table of Contents
Chapter 1 OAP Module Configuration Commands....................................................................1-1
1.1 OAP Module Configuration Commands ............................................................................1-1
1.1.1 oap connect slot......................................................................................................1-1
1.1.2 oap reboot slot.........................................................................................................1-2

Command Manual – OAP Module
H3C S9500 Series Routing Switches Chapter 1 OAP Module Configuration Commands
1-1
Chapter 1 OAP Module Configuration Commands
1.1 OAP Module Configuration Commands
1.1.1 oap connect slot
Syntax
oap connect slot slot-number
View
User view
Default Level
2: System level
Parameters
slot-number: Number of the slot where an OAP module resides.
Description
Use the oap connect slot command to switch from the command line interface on the
device to the operating system of the OAP module, and thus you can manage the
system of the OAP module.
You can press Ctrl+k to return from the operating system on the OAP module to the
command line interface on the device.
Examples
# Switch from the command line interface on the device to the operating system of the
OAP module in slot 3.
<Sysname> oap connect slot 3
Connected to OAP!
# After viewing the above information, press Enter to log in to the operating system of
the OAP module.
<H3C>
# Press Ctrl+k to return from the operating system on the OAPmodule to the command
line interface on the device.
<Sysname>

Command Manual – OAP Module
H3C S9500 Series Routing Switches Chapter 1 OAP Module Configuration Commands
1-2
1.1.2 oap reboot slot
Syntax
oap reboot slot slot-number
View
User view
Default Level
2: System level
Parameters
slot-number: Number of the slot where an OAP module resides.
Description
Use the oap reboot slot command to reset the system on an OAP module, which is
equal to resetting the OAP module by pressing the reset button on the OAP module.
It is recommended to save the data on the operating system on the OAP module and
shut down the operating system to avoid service interruption and hardware data loss.
After the reset, the operating system on the OAP module reboots automatically.
Examples
# Reset the system on the OAP module in slot 3.
<Sysname> oap reboot slot 3
This command will recover the OAP from shutdown or other failed state.
Warning: This command may lose the data on the hard disk if the OAP is not being
shut down!
Continue? [Y/N]:y
Reboot OAP by command.

Command Manual – ACSEI
H3C S9500 Series Routing Switches Table of Contents
i
Table of Contents
Chapter 1 ACSEI Configuration Commands ..............................................................................1-1
1.1 ACSEI Server Configuration Commands ..........................................................................1-1
1.1.1 acsei client close.....................................................................................................1-1
1.1.2 acsei client reboot ...................................................................................................1-1
1.1.3 acsei server.............................................................................................................1-2
1.1.4 acsei server enable.................................................................................................1-2
1.1.5 acsei timer clock-sync.............................................................................................1-3
1.1.6 acsei timer monitor..................................................................................................1-4
1.1.7 debugging acsei server...........................................................................................1-4
1.1.8 debugging acsei-client ............................................................................................1-6
1.1.9 display acsei client info .........................................................................................1-10
1.1.10 display acsei client summary ..............................................................................1-12