Haas+Sohn ROMA Instruction manual

Item No.: 0621850109031
V13 H06
1
Assembly and installation instructions ROMA
Room for type designation and manufacturing number:
Transfer from nameplate
Equipment type:
Manufacturing number:
Test no. insert: RRF-29 06 1192
Our supply program: Oil stoves
Fireplaces
Pellet stoves
Tiled and slow-burning stoves for wood and coal
Slow-burning stoves and auxiliary stoves for wood, coal and oil
Fireplace inserts for wood
Accessories for stove and fireplace
Accessories for central oil supply
Air humidifier
HAAS+SOHN
Vertrieb in Deutschland
OFENTECHNIK GMBH
HAAS+SOHN Ofentechnik GmbH
Urstein Nord 67
Herborner Straße 7-9
A-5412 Puch
D-35764 Sinn
eMail: [e-mail]
eMail: [email protected]
http://www.haassohn.com

Item No.: 0621850109031
V13 H06
2
1 PRELIMINARY REMARKS
Please read the assembly and operating instructions of your fireplace insert before these installation
instructions.
The following are additional parts of these installation instructions:
“Equipment sheet complete”,
installation instructions of the fire protection insulating set if applicable.
When unpacking the concrete elements, possible irregularities (cracks or joints) can be detected if
applicable, these should be filled with the enclosed adhesive.
2 PREREQUISITES
The load-carrying capacity of the floor must always be clarified before installing your fireplace kit.
The total weight of the complete fireplace kit (fireplace with refractory lining and the artificial stone
lining) can amount to approximately 370 to roughly 420 kg depending on the model. With wooden
beam ceilings it is essential to consult a structural engineer.
Important: Observe the regulation of the fire protection authorities and the national construction
regulations applicable at the place of installation when installing your fireplace kit: In particular,
flammable walls (e.g. wooden walls) or supporting walls made of reinforced concrete must be
protected from excessive heating. To screen flammable or structurally sensitive components from
impermissible exposure to heat, a fire protection insulating set is available as accessory to your
fireplace kit. This set includes several screen panels. We recommend attaching this fire protection
insulating set also with non-flammable walls.
3 TOOLS
For the installation of the artificial stone lining you will require the following tools:
–Water level
–rubber hammer
–open-end wrench size
13mm
–Steel square 90 o
–Pencil
–Paint roller
–Trowel
–Sponge
–
4 MATERIAL
–Paint
–Plaster if required
–Water
–Acrylic
5 KIT INSTALLATION
1. Carefully unpack the artificial stone lining including accessories. Check your kit for
completeness using the enclosed parts list. Sort the parts in accordance with the installation
sequence (see parts list text and illustration).

3
2. When using the fire protection insulating set, mount the two rear wall screen panels (see
installation instructions of the fire protection insulating set) to the rear wall of the fireplace.
3. Adjust the fireplace to the correct height using the open-end wrench size 13mm by turning the
adjustable feet. The ideal height is shown in Figure 2. For comparison, install the base with the
base plate. The lower edge of the panel with air damper on the fireplace can end flush with the
sub-structure of the concrete lining or be approximately 1 to 2 mm higher (Attention: The
gluing will result in a minimal change of the overall height: however it is possible to
subsequently adjust the correct height by turning the adjustable feet).
4. In addition to this the distance to the screen wall must be adjusted to the correct dimension (see
Figure 2).
Important: After this, adjust the fireplace horizontally using the water level.
5. Locate the flue pipe connection (e.g. with double wall lining) in the chimney (see installation
and operating instructions of the fireplace).
6. Now start installing the kit.
6 INSTRUCTIONS
It is not permissible to install the kit by gluing the elements together without protecting the fireplace
hood against slipping!
Following the installation, place the refractory lining in the fire chamber of your fireplace (see
equipment sheet of your fireplace). Why refractories last? Because the fireplace can be easier
repositioned while assembling the artificial stone kit.
To avoid minor joints between the kit and the wall we recommend to grout these with acrylic
compound (in contrast with silicon, acrylic can be painted over immediately).
Once the fireplace kit has dried, the fireplace can be painted (mineral-based paint, no depth primer
required). In order to achieve a fine-grain structure, simply mix some adhesive into the paint for
the first coat. Use only paint for the second coat. Of course roll-on or rub-on plasters can also be
used to finish the surface.
Allow the fireplace kit to dry for at least two weeks before initial start-up.
To start the fireplace: Carefully read the operating instructions and start the fireplace using little
wood. After approximately one hour the device can be heated to rated heat.

4
Artificial stone kit –ROMA–Parts list
Installation instructions artificial stone kit ROMA
Note: Prior to installation, check the exact position of the insert. Always ensure that the components
are installed level and plumb.
1. First install the lateral components of the fireplace kit in the dry state. Check to see if the
elements are level and plumb. Then mark the correct position using the pencil.
Remove all elements again and re-join in the sequence using the tile adhesive.
2. Mix the supplied adhesive (safety adhesive) with water until it has a consistency similar to
toothpaste. Glue all elements together and to the wall. Clean and lightly moisten the bonding
surface to achieve optimum adhesive strength. Remove excess adhesive with the trowel and a
moist cloth. Now the joints compensated with acrylic.
3. Once the kit has been finish painted, finally glue the base plates.
Item No.
No.
Quantit
y
Designation
Finish
Material
0621850100100
1
1
Lateral part left
Artificial stone
Artificial stone
0621850100200
2
1
Lateral part right
Artificial stone
Artificial stone
0621850100300
3
1
Base
Artificial stone
Artificial stone
0621850100400
4
1
Base blind left
Artificial stone
Artificial stone
0621850100500
5
1
Base blind right
Artificial stone
Artificial stone
0631850110600
6
1
Base plate front
Artificial stone
Artificial stone
0621850100700
7
1
Fireplace hood bottom
Slate
Artificial stone
0621850100800
8
1
Fireplace hood top
Artificial stone
Artificial stone
0631850110900
10
1
Base plate left
Artificial stone
Artificial stone
0631850110901
10
1
Base plate right
Slate
Artificial stone
0631850110902
10
1
Ledge plate left
Slate
Artificial stone
0631850110903
10
1
Ledge plate right
Slate
Artificial stone
0621850101100
11
1
Air grill top
Steel plate
Steel plate
0621850100900
9
1
Air grill lateral
Steel plate
Steel plate
0621800105000
1
Adhesive

5
Figure 3: Installing the base
Figure 2: Installing the
lateral parts
Figure 1: Position fireplace insert
Figure 4: Installing the base
left and right

6
Figure 5: Assembling the
fireplace hood bottom + top and
the air grill top
Figure 6: Installing the
base-and ledge plates and
the air grill

7

8
We wish you much pleasure with your fireplace kit by
Figure 7: Dimensions