Hafele 421.68.440 User manual

1
TV Lift
Mounting Instructions
Item No.: 421.68.440
Electrical TV Lift mechanism TS750
1
Parts included with your TV Lift
Lift unit ( #1 )
Power supply + bracket ( #2 )
R.F. Module ( #3 )
Rocker switch ( #4 )
Remote Control (not shown)
Plasma screen brackets ( #6a )
Lift Brackets ( #6b )
Lid Lifter ( #7 )
The TS750 TV Lift is designed to oper-
ate loaded with minimum 5 kg. It is im-
portant that the lift is used loaded to at
least the minimum kg to avoid exces-
sive operation noise especially on the
down cycle.
Mounting screw
holes (x3)
Mounting screw
holes
(
x2
)
Mounting screw
holes (x2)
)
#7, Lid lifte
r
#6b, Lift brackets (x2)
#6a, TV mounting
brackets
(
x2
)
#2, Power supply + bracket
#3
,
R.F. Module
#4
,
Rocker Switch
Anti-Pinch Guard
(
not included
)
#1, Lift unit
313740.9
Parts included with your TV Lift
Lift unit (#1 )
Power supply + bracket (#2 )
R.F. Module (#3 )
Rocker switch (#4 )
Remote Control (not shown)
Plasma screen brackets (#6a )
Lift Brackets (#6b )
Lid Lifter (#7 )
The TS750 TV Lift is designed to operate
loaded with minimum 5 kg. It is important
that the lift is used loaded to at least the
minimum kg to avoid excessive operation
noise especially on the down cycle.

2
Electrical TV Lift mechanism TS750
2
Important safety Instructions
Use the following safety guidelines to help protect your lift from potential damage and
to ensure your own personal safety.
Read all the installation instructions before testing or installing your lift.
Read and follow all safety instructions.
Keep remote control out of reach of children.
To prevent bodily injury keep hands and clothing away from the lift while the
lift is in operation.
Before installing the lift or working with its connections, unplug the lift from the
electrical shock.
Do not install the lift, power supply or R.F. module in places subject to extreme
temperatures for example near a radiator, or heating vent.
To avoid damaging the power supply, R.F. module and power cord, do not put
anything on it or place it where it could become damaged.
Unplug the lift in the following conditions:
When the power cord or plug is damaged or frayed.
If liquid has spilled into the lift, power supply or RF module.
If the lift, power supply or RF module has been exposed to rain
or water.
If the lift exhibits a distinct change in performance, indicating a
need for servicing.
CAUTION: Before you begin any of the Installation procedures on page 3,
read and follow the warnings and safety instructions on this page.
WARNING ! THIS IS NOT A TOY !
WARNING ! CHILDREN SHOULD NOT OPERATE LIFT OR
REMOTE CONTROL !

3
Electrical TV Lift mechanism TS750
3
Mounting Instruction for the TV Lift
1) Remove all contents from packaging and compare with parts lists. Test the lift
at the same time. Refer to the drawing and to the user instruction packed
along with the remote unit proceed as follows: Connect the lift (#1) to the RF
Module (#3). Once all connections have been made, plug power supply (#2)
into the wall socket. Position lift vertically. Test lift using rocker switch (#4) –
have lift travel a few inches and then back down. Use same method to test
remote. The rocker switch must be pressed continuously to make lift work. Re-
leasing switch will stop unit immediately. The remote starts the lift to move
continuously by one single pres on “up” or “down” button. The lift stops again
by pressing either “up” or “down” button again.
Please see “Helpful Hints” on page 4 before continuing
2) Place the lift unit (#1) on the back panel of cabinet in a location that will allow
full up and down movement of TV. Unit must be a minimum of 1/8” down from
the top edge of the cabinet.
3) Fasten the unit securely to the cabinet using the 7 screw holes shown in the
drawing on page one. Screws must be appropriate for the material being used.
Lift must be mounted vertically (using a level) inside cabinet.
4) Fasten the power supply + bracket (#2) on the back of the cabinet on the right
side of the unit as shown in the drawing. Secure with 2 screws.
5) Fasten R.F. Module (#3) next to the power supply leaving enough room to
connect wires.
6) Mount rocker switch (#4) to the upper part of the cabinet towards the front by
cutting a hole and pressing the switch into place. Secure excess wire to keep
away from moving parts.
7) Make connections as done previously for testing. Plug the power cord into wall
outlet and test the lift. Refer to the connection diagram below:

4
Electrical TV Lift mechanism TS750
4
8) Slide both flat screen brackets (#6a) onto the two lift brackets (#6b) as shown
in the drawing. Adjust the brackets to fit the mounting holes on the TV. Secure
brackets to the TV – MAKE SURE TV IS CENTERED ON BRACKETS.
9) Raise lift to uppermost position. Place TV in best position on lift based on the
size of the TV. Put bolts on lift bracket through lift front and bolt into position.
Lower lift with TV, making sure the TV does not extend past top edge of cabi-
net in the lowered position.
10)Insert lid lift (#7) into slot on lift with curve facing toward the front. The top of
the lifter curve must be above the top of the TV. With lift in the up position, use
allen wrench to secure lid lifter in place.
The instructions above are based on a typical cabinet installation.
Specifications:
Materials and weights: Steel, black powder coated - Weight ~ 20 kg
Max. working loads: 65 kg (by standard installation)
29 kg (when lift is mounted upside down)
100 kg peak load
Duty cycle: 10% by 50% of working load or max 2 min. continuously
Operation: Remote and rocker switch
Voltage:
Standby Consumption:
100-240 VAC / 50/60Hz
< 1 Watt
Helpful Hints:
a) Test lift mechanism and remote / rocker switch before mounting in cabinet.
b) Mount TV lift and electronics to plywood panel and attach to inside back of
cabinet using appropriate number of screws. This allows all components to be
removed from the cabinet if necessary. If this is not possible, create an ac-
cess panel to the electronics.
c) Create an Anti-Pinch Guard (#8) and mount to metal box on lift under TV us-
ing double-stick tape, Velcro, etc that will allow the guard to disengage under
pressure.

5
Declaration of conformity
We hereby declare, under our sole responsibility that the following products:
- Item No.: 421.68.440
which are covered by this statement, are in conformity with the following standards and other
normative documents:
- Counsel Directive 89/336/EØF with later changes
- Counsel Directive 73/23/EØF with later changes
The information in this document is subject to change without notice.
1-800-423-3531 • www.hafele.com