Haier AF072XCBAA Specification sheet

AF072XCBAA
AF092XCBAA
AF122XCBAA
AF142XCBAA
Console Type
No.0010573520
E
Cautions..................................................1-4
Parts and Functions .......................................5-8
Operation.............................................. 9-14
Maintenance........................................15
Trouble shooting.............................
Installation Manual of Room Air Conditioner17-22
CONTENTS
Before using the air conditioner, please read this manual carefully.
Please keep this manual properly forfuture use.
....16
R oom Air-conditioner indoor units
OPERATION AND INSTALLATION MANUAL

1
Disposal of the old air conditioner
Before disposing an old air conditioner that
goes out of use, please make sure it's
inoperative and safe. Unplug the air
conditioner in order to avoid the risk of child
entrapment.
It must be noticed that air conditioner
system contains refrigerants, which require
specialized waste disposal. The valuable
materials contained in an air conditioner can
be recycled. Contact your local waste
disposal center for proper disposal of an
old air conditioner and contact your local
authority or your dealer if you have any
question. Please ensure that the pipework
of your air conditioner does not get damaged
prior to being picked up by the relevant
waste disposal center, and contribute to
environmental awareness by insisting on
an appropriate, anti-pollution method of
disposal.
Disposal of the packaging of your
new air conditioner
All the packaging materials employed in the
package of your new air conditioner may be
disposed without any danger to the
environment.
The cardboard box may be broken or cut into
smaller pieces and given to a waste paper
disposal service. The wrapping bag made of
polyethylene and the polyethylene foam pads
All these valuable materials may be taken
to a waste collecting center and used again
after adequate recycling.
Consult your local authorities for the name
and address of the waste materials
collecting centers and waste paper disposal
services nearest to your house.
Safety Instructions and Warnings
Before starting the air conditioner, read the
information given in the User's Guide
carefully. The User's Guide contains very
important observations relating to the
assembly , operation and maintenance of
the air conditioner.
The manufacturer does not accept
responsibility for any damages that may
arise due to non-observation of the following
instruction.
Damaged air conditioners are not to be
put into operation. In case of doubt, consult
your supplier.
Use of the air conditioner is to be carried
out in strict compliance with the relative
instructions set forth in the User's Guide.
Installation shall be done by professional
people, don't install unit by yourself.
For the purpose of the safety,the air conditioner
must be properly grounded in accordance
with specifications.
Always remember to unplug the air
conditioner before openning inlet grill. Never
unplug your air conditioner by pulling on
the power cord. Always grip plug firmly and
pull straight out from the outlet.
All electrical repairs must be carried out
by qualified electricians. Inadequate repairs
may result in a major source of danger for
the user of the air conditioner.
Do not damage any parts of the air
conditioner that carry refrigerant by piercing
or performating the air conditioner's tubes
with sharp or pointed items , crushing or
twisting any tubes , or scraping the coatings
off the surfaces. If the refrigerant spurts
out and gets into eyes , it may result in
serious eye injuries.
Cautions

2
Do not obstruct or cover the ventilation
grille of the air conditioner. Do not put
fingers or any other things into the
inlet/outlet and swing louver.
Do not allow children to play with the air
conditioner. In no case should children be
allowed to sit on the outdoor unit.
Specifications
The refrigerating circuit is leak-proof.
1. Applicable ambient temperature range:
2. If the power supply cord is damaged, it
must be replaced by the manufacturer
or its service agent or a similar qualified
person.
3. If the fuse of indoor unit on PC board is
broken,please change it with the type of
T. 3.15A/ 250V.
4. The wiring method should be in line with
the local wiring standard.
5. The waste battery should be disposed
properly.
6. The appliance is not intended for use by
young children or infirm persons without
supervision.
7. Young children should be supervised to
ensure that they do not play with the
applience.
8. A breaker should be used in the circuits,
which should be all-pole cutoff and the
distance between its two contacts should
be not at least 3mm .
9.The power plug and connecting cable
must have acquired the local attestation.
The machine is adaptive in following
situation
Cautions
Cooling
Heating
Indoor
outdoor
Rated Maximum Minimum
27 32 18
19 23 14
35 43 10
24 26 6
20 27 15
14.5 -- --
7 24 -7
6 18 --
DB C
WB C
DB C
WB C
Indoor
outdoor DB C
WB C
DB C
WB C

3
Cautions
Please read the following Safety Instructions carefully prior to use.
The instructions are classified into two levels, WARNING and CAUTION according to the
seriousness of possible risks and damages as follows. Compliance to the instructions are
strictly required for safety use.
Safety Instruction
Installation WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works may
cause electric shock, fire, water leakage.
CAUTION
Installation in an inadequate place may cause accidents. Do not install in the following place.
Connect the earth
cable.
PROHIBITION PROHIBITION
STRICT
ENFORCEMENT
Do not install in the
place where there
is any possibility
of inflammable
gas leakage around
the unit.
Do not get the unit
exposed to vapor
or oil steam.
Check proper
installation of the
drainage securely
Use fuse with specified capacity.
Replacement with steel or copper wires are
absolutely prohibited.
Grounding wire should not be connected to
that of gas pipeline, water pipeline,lighting
arrester or telephone.
FUSE
STEEL WIRE
COPPERWIRE
STRICT
ENFORCEMENT

Use of Air Conditioner
Cautions
STRICT
ENFORCEMENT
4
When abnormality such as burnt-small found, immediately
stop the operation button and contact sales shop.
Connect power supply cord to the
outlet completely. After installed, the unit shall be
tested for electric leakage.
Take care not to damage the
power supply cord.
Do not use power supply cord in
a bundle.
Do not use power supply cord
extended or connected in halfway.
Do not insert objects into the air
inlet or outlet.
Do not try to repair or reconstruct
by yourself.
PROHIBITION
PROHIBITION
PROHIBITION PROHIBITION
PROHIBITION
OFF STRICT
ENFORCEMENT
STRICT
ENFORCEMENT
Use an exclusive power source with a circuit breaker.
CAUTION
Do not use for the purpose of
storage of food, art work, precise
equipment, breeding , or cultivation.
Take fresh air occasionally
especially when gas appliance is
running at the same time.
Do not operate the switch with wet
hand.
Do not pour water onto the unit
for cleaning.
Check good condition of the
installation stand.
Do not install the unit near a fireplace
or other heating apparatus.
Do not place animals or plants in
the direct path of the air flow. Do not place any objects on or climb on the unit. Do not place flower vase or water
containers on the top of the unit.
PROHIBITIONPROHIBITION
PROHIBITIONPROHIBITION
PROHIBITION
PROHIBITION PROHIBITION
PROHIBITION
STRICT
ENFORCEMENT
WARNING
Do not channel the air flow directly
at people, especially at infants or
the aged.
Do not start or stop the operation
by disconnecting the power supply
cord and so on.
PROHIBITION

5
Parts and Functions
1
3
4
5
2
1.OUTLET
2.CONTROL PANEL
3.INLET
4.FILTER ( inside )
5.OUTLET
Remote controller
Indoor unit
FRESH
HIGH/SO TIMER
SET
FILTER
BA
M D
HEALTH
RESET LOCK
SLEEP
FAN
TEMP
ON
OFF
SWING
MODE
CLOCK
CODE LIGHT
OFF
A
U
T
O
HEAT

Parts and Functions
CAUTION
Before opening the front grille, be sure
to stop the operation and turn the
breaker OFF.
Do not touch the metal parts on the
inside of the indoor unit, as it may result
in injury.
ON/OFF button
Push once to start operation,
push once again to stop it.
Operation is set to AUTO, air
flow is set to AUTO FAN.
(page 9)
Use when remote controller is
not available.
Receiver
Signals are received from the remote
controller here.
Upon receiving a signal, there is a receiving
sound.
Air outlet selection switch
This setting blows air from upper outlet only.
This setting automatically decides a blow
pattern depending on mode and conditions.
This setting is
recommended.
The unit is shipped from the
factory with this setting.
Air outlet
selection
Room temperature sensor
Senses the air temperature around the unit.
6

Parts and Functions
7
25
26
21
23
36
FRESH
HIGH/SO TIMER
SET
FILTER
BA
M D
HEALTH
RESET LOCK
SLEEP
FAN
TEMP
ON
OFF
SWING
MODE
CLOCK
CODE LIGHT
OFF
A
U
T
O
1
2
3
4
6
7
9
10
13
17
15
5
8
18
19
22
34
33
24
27
28
32
31
30
35 20
14
16
Remote controller
1.TEMP Setting Button
(Used to set temperature. Setting ranges:
16 C to 30 C)
In Up/Down function, for controlling up and
down filter.
2.SWING Button
If you press this button once, auto swing will
be activated.
If you press this button again, the louver will
fix in the present position.
3.Power ON/OFF Button
Used for unit start and stop
After power on, the LCD of remote controller
will display the previous operation state (except
for TIMER,SLEEP and SWING state).
4.Operation MODE
Used to select operation mode.
Every time you press MODE button, operation mode
changes according to following sequence:
6.CLOCK Button
Used to set correct time.
AUTO FAN HEAT
COOL DRY
7.TIMER Button
Used to select TIMER mode:TIMER ON,TIMER
OFF, TIMER ON/OFF.
(Note: if time of TIMER ON is the same as TIMER
OFF,TIMER ON/OFF cannot be set)
10.RESET Button
Press this button by using a sharp article to resume
the correct operation of the remote controller in case
of need, i.e. for example in case of malfunctions due
to electromagnetic disturbance.
5.HEALTH Button
13.HOUR Adjustment
Used to set clock and timer setting
15.SET Button
Used to confirm TIMER and CLOCK settings when heating
or cooling.
8. FILTER Button
Used to set up/down function of filter.
9.CODE Button
Used to select Code A or B, this manual is for CodeA.
12
11
29
14.HIGH/SO Button
Used to select HIGH or SOFT operation.
11.LIGHT Button
Used to light the control panel (only for cabinet unit)
12.LOCK Button
Used to lock operation button and LCD display contents:
by pressing this button, other buttons comes out of
function and lock state display appears; if you press it
again, lock state will be no more active and lock state
display will disappear.
16.FRESH Button
Used to set fresh mode, the unit will draw in fresh air.
NOTE: 1.Single cooling air conditioner does not have the displays and functions related to heating.
2.This kind of unit does not have the following related functions and displays:
3.HIGH/SO button
This button is active in Cooling/Heating mode, the fan speed is in AUTO mode after pressing it and
" high functon/soft function " will be automatically cancelled after 15 minutes running.
5 8 16 21 27 28 29 33
HEAT
37
37

8
Parts and Functions
Clock Set
Displays when healthy run function is set.
22.TEMPERATURE Display
34.LOCK State Display
33.BATTERY Energy Display
Notify the user when it is time to change
the batteries.
24.HIGN/SO Run Display
26.SIGNAL SENDING Display
28.Fresh Display
29.Auxiliary ELECTRICAL HEATING Display
30.HEALTH Display
32.SLEEP State Display
31.Operation MODE Display
AUTO RUN COOL RUN DRY RUN HEAT RUN FAN RUN
35.FAN SPEED Display
23.AUTO SWING Display
20.TIMER Display
21.FILTER Display
36.TIMER ON Display
When unit is started for the first time and after replacing batteries in remote
controller, clock should be adjusted as follows:
1.Press CLOCK button, clock indication of " AM " or " PM " flashes.
2.Press or to set correct time. Each press will increase or decrease
1 min. If the button is kept pressed, time will increase or decrease quickly.
3.After time setting is confirmed, press "SET" : AM or PM stop flashing,
while clock starts working.
Note:AM means morning and PM means afternoon.
When operating the remote controller in an area where
electronically controlled lights are installed or wireless
handsets are used, please move closer to the indoor unit
as the function of the remote controller might be affected
by signals emitted by the above mentioned equipments.
Battery loading
Confirmation indicator
If no indication is displayed after press ON/OFF button,
reload the batteries.
Remote Controller Operation
When in use, direct signal transmission
head to the receiver placed on the
indoor unit
The distance between the remote controller and the receiver
should be max 7m and there should be no obstacle between
them.
Do not throw the remote controller; prevent it from being
damaged.
17.SLEEP Button
(The clock must be corrected before setting sleep function)
Used to set sleep mode.
18.FAN Button
Used to select fan speed:LOW,MID,HIGH,AUTO.
19.TIMER OFF Display
When the filter need be cleaned, the sign will
appear automatically.
25.Code A display
Code A is used for this unit
27.Code B display
37.HEAT Button
Used to select auxiliary heater.
Battery loading
Batteries are fitted as follows:
Loading the battery
Ensure that batteries are correctly placed in the compartment as
required for positive and negative terminals.
Replacing the battery compartment lid
The battery compartment lid is reinstalled in the reverse sequence.
Display review
Press the button to see if batteries are properly fitted. If no display
appears, refit the batteries.
Remove the battery compartment lid
Slightly press and disengage the battery compartment lid
marked with ì î and then hold the remote controller by the
upper section and then remove the battery compartment
lid by pressing in the direction of the arrow as shown in the
figure above.
+ -
- +
Note:
It is recommended that the batteries be removed from the
compartment if the remote controller is not used for an
extended period.
The remote controller is programmed for automatic test of
operation mode after the batteries are replaced. When the
test is conducted, all icons will appear on the screen and
then disappear if the batteries are properly fitted.
When throw away the waste batteries, please perform in
accordance with the local regulation.
Caution:
If the remote controller does not operate as designed after
fitting new batteries of the same
type, press the Reset button (marked ) with a pointed
article.
FRESH
HIGH/SO TIMER
SET
FILTER
HEALTH
RESET LOCK
SLEEPMODE
CLOCK
CODE LIGHT
3
2
1
LOW MID HIGH
HEAT

9
AUTO, COOL , HEAT and DRY Operation
1. Unit start
Press ON/OFF button,unit starts.
Previous operation status appears on LCD (except for
TIMER,SLEEP and SWING setting)
3.Temperature setting
Then select AUTO run or select COOL operation or
select DRY operation or select HEAT operation
2.Select operation mode
Press MODE button. At each press, operation mode
changes as follows:
Press TEMP button.
Every time the button is pressed, temp. setting increases
1 C; if the button is kept pressed, temp. setting will increase
quickly.
Every time the button is pressed, temp. setting decreases
1 C, if the button is kept pressed, temp. setting will decrease
quickly.
Set proper temperature
4.Adjust FAN button
Press FAN button.At each press, fan speed changes as follows:
Air conditioner will run at the selected fan speed.
5. Unit stop
Press ON/OFF button,unit stops.
InATUO mode, the temperature setting is not displayed on LCD. In this mode, during running air conditioner
will select COOL, HEAT or FAN mode automatically according to the room temperature.
In DRY mode, when room temperature becomes 2 C higher than temperature setting, unit will run intermittently
at LOW speed regardless of FAN setting. When room temperature is lower than temperature setting, unit will
only run FAN operation.
In HEAT mode,warm air will blow out after a short period of time due to cold-draft prevention function.
AUTO FANHEATCOOL DRY
AUTO LOW MID HIGH
FRESH
HIGH/SO TIMER
SET
FILTER
A
HEALTH
RESET LOCK
SLEEP
FAN
TEMP
ON
OFF
SWING
MODE
CLOCK
CODE LIGHT
A
U
T
O
HEAT
Temp. setting +2 C
Temp.setting
On reaching temp.setting
+2 C, unit will run in mild
DRY mode.
Ultra-low air flow
COOL operation starts
when room temp.is
higher than temp.
setting.
3
51
3
4
2
A
U
T
O