Haier AS25S2SN1FA-NR User manual

Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
SPLIT TYPE ROOM AIR CONDITION
OPERATION MANUAL
ER
AS25S2SN1FA-NR
AS35S2SN1FA-NR
AS50S2SN1FA-NR
0011500387
danish

Outlet
Horizontal flap
Display board
(adjust up and down air flow
Don't adjust it manually)
(adjust left and
ow)
Vertical blade
Emergency
Switch
right air fl
Inlet
Air Purifying Filter
(inside)
Inlet grille
(inside)
Parts and Functions
Indoor Unit
Outdoor Unit
Remote controller
Outer side of the controller
OUTLET CONNECTING PIPING
AND EL
EC
T
RI
C
AL WIRIN
G
I
N
L
ET
DRAIN H
O
SE
4
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
1.
S
ELF CLEAN button
2. DRY button
3
. COOL button
Used to set COOL operation.
4.
5.
n
.
6 oitcnufhcaefoyalps
i
D
status
8. WIFI and CLOCK display
7.
O
peration mode display
9.
T
EMP display
10. Humidity display
11. FAN SPEED display
F
12.
S
WING display
Swing up/down display
swing left/right display
14. TURBO button
15. QUIET button
16. HEAT button
17. FAN button
Used to set DRY operation.
13.
T
IMER ON display
TIMER OFF display
CLOCK display
1
4
5
6
7
89
10
11
12
13
15
16
17
14
TEMP button
used to change setting
temperature
ON / OFF button
1
NOTE:
a. Humidity display is unavailable on some models
b. If the model you buy has a WIFI function, press the“ON/OFF”
button for 5s to emit the WIFI binding signal. Once in the
binding mode, the APP will show how to bind.
TIMER
3
2
SELF CLEAN
TURBO
Display board
Signal receiver hole
COOL display
HEALTH display
4
2
3
1
5
DRY display
6
Ambient temp.display
When receiving the remote
control signal, display the set
temperature.
2
35
6
4
HEAT display
1

Operation
4
Unit will start running to reach the
temp. setting on LCD.
A
N O
pe
ration
A
changes as follows:
Unit will run at selected fan speed.
button.
pressed, temp. setting
increases 1 ºC.
pressed, temp. setting
decreases 1 ºC.
1
21SELF CLEAN
TIMER
SELF CLEAN
TURBO
TIMER
SELF CLEAN
TURBO
SELF CLEAN
Functional description:
the purpose of this function is to clean the evaporator.
Entry and exit
Press SELF CLEAN button to enter this function, then
it will display "CL" on the panel of the indoor unit and also
on the remote controller. Maximum running time not more
than 25 minutes, this function will exit automatically with
the " Pi " sound twice, then the unit return to original state.
Under operation process of SELF CLEAN, press the button
repeatedly is invalid and cannot exit, please press the
“power” button or swift to other mode to exit.
Note:
1.This function is invalid in timer / sleep mode.
2.After this mode starts, the air volume may reduce or
even have no airflow,or even cold airflow blowing.
3.It is normal if the unit make some sound like expand with
heat and contract with cold
4. The “CL” display time may last differently on the remote
controller and panel.
5.If the outside ambient temperature below zero, error
code “F25 “may be occurred during self-cleaning operation ,
which is normal protection, please turn off the power
and to restart after 10 seconds .
6.The best condition to run this mode: the temperature is
20 ~27 and the humidity is 35 ~60 in the door,
the temperature is 25 ~38 cooling season out the
door.
7.It is hard to frost if the air is too dry(humidity 20%). and
if the humidity is too high(humidity 70%).the condensate
water may increase, which may move away some frost.
TURBOTURBO
4