Haier HAIDSJP63MC User manual

Besoin d’un conseil ? Une question sur ce produit ?
RDV sur la communauté SAV Darty : https://sav.darty.com
Déjà 1/2 million de solutions grâce à l’avis des utilisateurs.
HAIER
PLAQUE INDUCTION
HAIDSJP63MC
1RWLFHGXWLOLVDWLRQ

1 1
1:1
K
项目
库
文件名
A
1246
35
1246
35
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
技术要求(版本号: A , 2018-01）
广东美的生活电器制造有限公司
材料:80G双胶纸
彭娟 卢灿飞制 图
设 计
校 对
审 核
标准化
审 定
日 期
标记 处数 更改文件号 签 字 日 期
多头电磁炉
使用说明书
重点
校对项
1.版面尺寸
2.材质标注
3.物料编码
4.颜色标注
5.客户型号
6.产品名称
7.重量标注
8.电压功率
古广君
古广君
-----
-----
----- 20211230
1、印刷颜色：钉装，单色；
2、说明书幅面大小为：210*290mm;
3、1:1图纸在第二页；
4、警语部分首字母高度≥3MM；
PN:**
HAIER-MC-IT7142B1C-AW HAIDSJP63MC
会 签

Instruction Manual For Induction Hob
ENGLISH
Manuel d'instruction pour plaque à induction
FRANÇAIS
HAIDSJP63MC
Thank you for purchasing the HAIER induction hob. Please read this instruction manual
carefully before using the hob and keep it in a safe place for future reference.

EN-2
Hereby, Candy Hoover Group Srl declares that the radio
equipment is in compliance with Directive 2014/53/EU and with the
relevant Statutory Requirements (for the UKCA market). The full
text of the declaration of conformity is available at the following
internet address: www.candy-group.com

EN-3
ENGLISH

Haier
Haier
EN-4

Haier
EN-5
ENGLISH

1. Max. 1500/2000 W zone
2. Max. 1500/2000 W zone
3. Max. 3000/3600 W zone
4. Glass plate
5. Control panel
1. Heating zone power controls
2. “Cook with me function” control
3. Timer control
Keylock
5. ON/OFF control
.4
1
2
3
4
5
1
2
3
45
EN-6
2

EN-7
• The controls respond to touch, so you don’t need to apply any pressure.
• Use the ball of your finger, not its tip.
• You will hear a beep each time a touch is registered.
• Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them.
Even a thin film of water may make the controls difficult to operate.
• Only use cookware with a base suitable for induction cooking.
Look for the induction symbol on the packaging or on the bottom
of the pan.
• You can check whether yourcookware is suitable by carrying out a magnet test.
Move a magnettowards the base of the pan. If it is attracted,the pan is suitable
for induction.
• If you do not have a magnet:
1. Put some water in the pan you want tocheck.
2. If does notflash in the display and the water is heating, the pan is suitable.
• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or copper
without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone.
Use pans whose diameter is as large as the graphic of the zone selected. Using a pot a slightly wider energy will be
used at its maximum efficiency. If you use smaller pot efficiency could be less than expected. Pot less than 140 mm
could be undetected by the hob. Always centre your pan on the cooking zone.
Always lift pans off the Induction hob – do not slide, or they may scratch the glass.
Touch Controls
Choosing the right Cookware
ENGLISH

How to use
Touch the ON/OFF control for three seconds. After power on, the
buzzer beeps once, all displays show “–” or “– –”, indicating that the
induction hob has entered the state of standby mode.
Place a suitable pan on the cooking zone that you wish to use.
• Make sure the bottom of the pan and the surface of the cooking
zone are clean and dry.
Touching the heating zone slider control , and a indicator next to the
key will flash.
Select a heat setting by touching the slider control
• If you don’t choose a heat setting within 1 minute, the Induction
hob will automatically switch off. You will need to start again at step 1.
• You can modify the heat setting at any time during cooking.
Start cooking
EN-8
power up
power down
If the display flashes alternately with the heat setting
This means that:
•you have not placed a pan on the correct cooking zone or,
• the pan you’re using is not suitable for induction cooking or,
• the pan is too small or not properly centered on the cooking zone.
No heatingtakes place unlessthere is a suitable pan on the cookingzone.
The display will automatically disappear after 1 minute if no suitable pan is placed on it.

Touching the heating zone selection control that you wish to
switch off.
the display shows “0”.
Turn the whole cooktop off by touching the ON/OFF control.
Beware of hot surfaces
H will show which cooking zone is hot to touch. It will
disappear when the surface has cooled down to a safe
temperature. It can also be used as an energy saving function
if you want to heat further pans, use the hotplate that is still
hot.
Activate the boost function
Touching the heating zone slider control
Touching the slider to “B”. Make sure the display shows “b”.
Cancel the Boost function
Touching the heating zone slider control that you wish to cancel
the boost function.
the display shows “0”.
Finish cooking
Using the Boost function
Turn the cooking zone off by touching the slider to “ 0 ”. Make sure
Turn the cooking zone off by touching the slider to “ 0 ”. Make sure
EN-9
ENGLISH

• The function can work in any cooking zone.
• The cooking zone returns to its original setting after 5 minutes.
• If the original heat setting equals 0, it will return to 9 after 5 minutes.
• You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones
on).
• When the controls are locked, all the controls except the ON/OFF control are disabled.
When the hob is in the lock mode, all the controls are disable except the ON/OFF , you can always turn the induction
hob off with the ON/OFF control in an emergency, but you shall unlock the hobfirst in the next operation.
• You can pause the heating instead of shutting the hob off.
• When entering the Pause mode, all the controls except the ON/OFF control are disabled.
To enter pause mode
Short touch the Timer “ ” and Timer ” ” at the same
time.
All the indicator will show “ 11“
To exit pause mode
Short touch the Timer “ ” and Timer ” ” at the same time.
When the hob is in the pause mode, all the controls are disable except the ON/OFF , you can always turn the
induction hob off with the ON/OFF control in an emergency. The hob will shut down after 10min if you don’t exit the
pause mode.
• it is possible to set a maximum power absorption level for the induction hob, choosing up to different power
ranges.
• induction hobs are able to limit themselves automatically in order to work at lower power level, to avoid the risk of
overloading.
Locking the Controls
Pause Mode
Power Management Function
The timer indicator will show “ Lo ”
To lock the controls
To unlock the controls
Touch and hold the lock control for a
while.
Touch and hold the lock control for a while.
EN-10

To enter Power Management Function
”. .
The timer indicator will show “ P5“ which means power
To switch to another level
There are 5 power levels, from “P1” to “p5”. The timer
indicator will show one of them.
“P1” : the maximum power is 2.5kW.
“P2” : the maximum power is 3.5kW.
“P3” : the maximum power is 4.5kW.
“P4” : the maximum power is 5.5kW.
Confirmation and Exit Power Management Function
”
for confirmation .
Then the hob will be turned off.
You can use the timer in two different ways:
•You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the set time is
up.
• You can set it to turn one or more cooking zones off after the set time is up.
The timer of maximum is 99min.
Timer control
level 5 The default mode is on max power of he hob.
“P5” : the maximum power is max power of the hob.
Turn on the hob, then Press at the same time keylock
press +/- of the timer
control and Timer
”
Press at the same time keylock control and Timer ”
EN-11
ENGLISH
or

a) Using the Timer as a Minute Minder
If you are not selecting any cooking zone
Make sure the cooktop is turned on.
Note: you can use the minute minder even if you’re not selecting any
cooking zone.
Touch “+” the controls of the timer. The minder
indicator will start flashing and “10” will show
in the timer display.
Set the time by touching the “-” or “+” control
of the timer
Hint: Touch the “-” or “+” control of the timer
once to decrease or increase by 1 minute.
Touch and hold the “-” or “+” control of the timer to decrease or
increase by 10 minutes.
When the time is set, it will begin to count down
immediately. The display will show the remaining
time and the timer indicator will flash for 5 seconds.
Buzzer will beep for 30 seconds and the timer
indicator shows “- - “ when the setting time finished.
b) Setting the timer to turn one or more cooking zones off
Set one zone
Touching the heating zone slider control
Set the time by touching the or control of the timer
Hint: Touch the “-“ or “+” control of the timer
once will decrease or increase by 1 minute.
Touch and hold the ”-“ or “+”control of the timer
will decrease or increase by 10 minutes.
When the time is set, it will begin to count down immediately. The display
will show the remaining time and the timer indicator flash for 5 seconds.
NOTE: The red dot next to power level indicator will illuminate
indicating that zone is selected.
EN-12

When cooking timer expires, the corresponding cooking zone will be
switched off automatically.
Other cooking zone will keep operating if they are turned on previously.
set more zones:
The steps for setting more zones are similar to the steps of setting one zone;
When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking zones are on.
The minute display shows the min. timer. The dot of the corresponding zone flashes.
The shown as below:
(set to 15 minutes)
(set to 45 minutes)
Once the countdown timer expires, the corresponding zone will
switch off. Then it will show the new min. timer and the dot of
corresponding zone will flash.
The shown as right:
(set to 30 minutes)
Touch the heating zone selection control, the corresponding timer will be shown in the timer indicator.
c) Cancel the timer
Touching the heating zone slider control that you want to cancel
the timer
Touch and hold the timer control “ - ”, the timer decreases to “00”
and the timer is cancelled.
Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever you forget to
turn off your cooking. The default working times for various power levels are shown in the below table:
Power level 1 2 3 4 5 6 7 8 9
Default working timer (hour) 8 8 8 4 4 4 2 2 2
When the pot is removed, the induction hob can stop heating immediately and the hob automatically switch off after 2
minutes.
People with a heart pace maker should consult with their doctor before using this unit.
Default working times
EN-13
ENGLISH

To make the pairing between Hob and APP use the following process:
When wi-fi ON: one dot will appear on the right side of the LED
When WIFI OFF: No dot will appear.
“Cook with me function”
Press 4 seconds the "Cook with me" button on the hob. Once the 4 seconds have passed, the digit of the TIMER starts to
blink with PA written on it and starts the pairing process. Now follow the instructions from the App.
How to set Cook with me
If you want to get out of "Cook with me" function change the power
level of the zone.
First of all, you should download hOn App and install to your portable device. Then enroll your induction hob following the
instructions directly from the App.
Choose from the hOn App recipes menu or special programs menu.
Follow step by step the indications on the App and when you have
finished send the parameters to the hob that will cook for you.
When the hob receives the command from the app, the hob will beep
for 2 times and blink for one second to indicate that the instructions
have been received.
a. WIRELESS PARAMETERS
Technology Wi-Fi BLE NFC
Standard IEEE 802.11b/n/g Bluetooth v4.2, BR/EDR, BLE /
Frequency Band(s) [MHz] 2402-2480 2402-2480 /
Maximum Power [mW] 1500 1500 /
EN-14
.
.
Download the App
After the beep you need to press the Cook with me button in order to
launch the recipes or program.

Selection of cooking vessels
You may have a number of different cooking vessels
1. This induction hob can identify a variety of cooking vessels, which you can test by
one of the following methods:
Place the vessel on the cooking zone. If the corresponding cooking zone displays a
power level, then the vessel is suitable. If “U” flashes, then the vessel is not
suitable for use with the induction hob.
2. Hold a magnet to the vessel. If the magnet is attracted to the vessel is suitable for
use with the induction hob.
NB: The base of the vessel must contain magnetic material.
It must have flat bottom with a diameter according to the table 1 below.
3. Use only ferromagnetic cookwares made from enameled steel, cast iron or stainless
steel but compatible with induction
4. Use pans whose diameter of the ferromagnetic area (base of the pan) is in the range
of dimensions in the table below. (Table 1)
- If you use smaller pots, performance could be affected
- If you use pot with a diameter smaller than the one indicated in the table 1, pots
may not be detected
According to the dimension of the zone you can use pots of different diameters as picture
below:
Iron oil frying
Stainless steel
Iron pan Iron kettle
Enamel
stainless steel
kettle
Enamel cooking
utesil
Iron plate
EN-15
ENGLISH

5. If the ferromagnetic part covers only partially the base of the pan, only the
ferromagnetic area will heat up, the rest of the base may not heat up a sufficient
temperature for cooking.
6. If the ferromagnetic area is not homogeneous, but presents others material such as
aluminum this may affect the heating up and the pan detection.
If the base of the pan is similar to the pictures below the pan could be not detected.
EN-16
The base diameter of induction cookware
Cooking zone
1 & 2 140
160 290
180
3
The above may vary according to the size of the pan and the material it is made from.
Minimum(mm) Maximum(mm)

The induction hob is equipped with a self diagnostic function. With this test the technician is able to check the function
of several components without disassembling or dismounting the hob from the working surface.
Troubleshooting
1) Failure code occur during customer using & Solution;
Failure code Problem Solution
Auto-Recovery
E1 Supply voltage is above the rated voltage. Please inspect whether power supply is normal.
Power on after the power supply is normal.
E2 Supply voltage is below the rated voltage.
E3 High temperature of ceramic plate sensor . 1# Wait for the temperature of ceramic plate return
to normal.
Touch “ON/OFF” button to restart unit.
E4 High temperature of ceramic plate sensor . 2#
E5 High temperature of IGBT . 1# Wait for the temperature of IGBT return to
normal.
Touch “ON/OFF” button to restart unit.
Check whether the fan runs smoothly;
if not , replace the fan.
E6 High temperature of IGBT. 2#
No Auto-Recovery
F3/F6 Ceramic plate temperature sensor failure- -short
circuit. (F3 for 1#,F6 for2#)
Check the connection or replace the ceramic
plate temperature sensor.
F4/F7 Ceramic plate temperature sensor failure--open
circuit. (F4 for 1#,F7 for2#)
F5/F8 Ceramic plate temperature sensor
failure—invalid . (F5 for 1#,F8 for2#)
F9/FA Temperature sensor of the IGBT failure. short
circuit/open circuit for 1# Replace the power board.
FC /FD Temperature sensor of the IGBT failure. short
circuit/open circuit for 2#
) )
) )
) )
)
)
)
)
EN-17
ENGLISH

2) Specific Failure & Solution
Failure Problem Solution A Solution B
The LED does not
come on when unit is plugged
in.
No power supplied. Check to see if plug is
secured tightly in outlet and
that outlet is working.
The accessorial power
board and the display
board connected failure.
Check the connection.
The accessorial power
board is damaged.
Replace the accessorial
power board.
The display board is
damaged.
Replace the display board.
Some buttons can’t work, or
the LED display is not normal.
The display board is
damaged.
Replace the display board.
The Cooking Mode Indicator
comes on, but heating does
not start.
High temperature of the
hob.
Ambient temperature may be
too high. Air Intake or Air
Vent may be blocked.
There is something wrong
with the fan.
Check whether the fan runs
smoothly;
if not , replace the fan.
The power board is
damaged.
Replace the power board.
Heating stops suddenly
during operation and the
display flashes “u”.
Pan Type is wrong. Use the proper pot (refer to
the instruction manual.)
Pan detection circuit
is damaged, replace
the power board.
Pot diameter is too small.
Cooker has overheated; Unit is overheated. Wait for
temperature to return to
normal.
Push “ON/OFF” button to
restart unit.
Heating zones of the same
side ( Such as the first and
the second zone ) would
display “u” .
The power board and the
display board connected
failure;
Check the connection.
The display board of
communicate part is
damaged.
Replace the display board.
The Main board is
damaged.
Replace the power board.
Fan motor sounds abnormal. The fan motor is damaged. Replace the fan.
The above are the judgment and inspection of common failures.
Please do not disassemble the unit by yourself to avoid any dangers and damages to the induction hob.
EN-18