Haier 3000 Series User manual

User Manual Model
3000/4000 Series
Guide de l’Utilisateur
3000/4000 Series
Manual del Usuario Modelo
3000/4000 Series
Range Hood
Extractor de Aire
Hotte de Cuisinière

English
1
SAFETY PRECAUTIONS
WARNING!
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have
questions, contact our customer service department for assistance.
Our Toll-Free number is 1-877-337-3639.
2. Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnection means to prevent power from being switched
on accidentally. When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by a qualified person(s)
in accordance with all applicable codes and standards, including fire-rated
construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent backdrafting.
Follow the heating equipment manufacturer’s guideline and safety standards
such as those published by the National Fire Protection Association (NFPA),
and the American Society of Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
6. To reduce the risk of fire or electric shock, do not use this range hood with an
additional speed control device.
7. Ducted fans must always be vented to the outdoors.
8. To reduce the risk of fire, use only metal ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers cause smoking
and greasy spillovers that may ignite. Heat oils slowly on low or medium
settings.
2. Always turn hood ON when cooking at high heat or when cooking flaming
foods.
3. Clean ventilating fans frequently. Grease should not be allowed to accumulate
on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size of the
surface element.

English
2
Thank you for using our Haier product.
This easy-to-use manual will guide you
in getting the best performance from
your Haier Range Hood.
Remember to record the model and
serial number. They are on a label in
the range hood.
Model number
Serial number
Date of purchase
Staple your receipt to your manual.
You will need it to obtain warranty service.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then
turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not
go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent steam
explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you already know how
to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
*Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION!
Important – Observe all governing codes and ordinances.
1. For general ventilation use only. Do not use this appliance to exhaust
hazardous or explosive materials and vapors.
2. To reduce the risk of fire, use only metal ductwork.
3. To avoid damage to motor or other components, keep drywall spray,
construction dust, etc. off the power unit.
4. Please read specification label on product for further information and
requirements.
SAVE THESE INSTRUCTIONS
for Future Use

English
3
Accessories
Range Hood Accessories Provided:
1 Range Hood
1 7” Round Duct Plate
1 Damper/Duct Connector
4 Damper Screws
4 Washers
4 Range Hood Wood Screws
2 Wire Connectors
2 HEPA or Charcoal Filters*
1 User Manual
*4000 series models come with HEPA filters. 3000 series models come with
HEPA or charcoal filters.
Check to make sure that all parts and accessories are present and in good
condition. If you find that they are not in good condition or are missing, please
contact our customer service department for assistance.
Our Toll-Free number is 1-877-337-3639.
Table Of Contents
PAGE
Safety Precautions......................................................................................1
Accessories ...............................................................................................3
Installation Preparation ...............................................................................4
Preparing Hood Location ............................................................................4
Preparing Hood...................................................................................... 5-9
Preparing Electrical Connections................................................................10
Installing Hood ........................................................................................11
Operating the Range Hood.................................................................. 12-14
Use and Care..........................................................................................15
Troubleshooting .......................................................................................16
Warranty Information ...............................................................................17

English
4
Installation Preparation
To install this range hood, you will need the following tools and materials:
Note: This procedure will require 2 people for easier installation.
Tools Needed for Installation
• Drill
• 1/8” Drill bit for drilling pilot holes
• 1-1/4” Wood bit for drilling electrical wiring access hole
• Phillips head screwdriver
• Flat-head screwdriver
• Pliers
• Pencil, ruler and level for marking range hood location
• Hand saw or jig saw for cutting the wall or cabinet openings
• Hi-Temp duct tape
• Electrical tape
• Connector Clamp
Preparing Hood Location
1. Determine whether hood will discharge vertically (3¼” x 10” or 7” Round),
horizontally (3¼” x 10” only) or non-ducted. For vertical or horizontal discharge,
run ductwork between the hood location and a roof cap or wall cap. For best
results, use a minimum number of transitions and elbows.
2. Use diagram, below, for proper placement of ductwork and electrical cutout in
cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole.
3. Run house wiring between service panel and hood location.

English
5
1. Remove 7” Round Duct Plate from top of hood. Set duct plate aside - with
mounting screws.
2. Remove tape holding filters in place. Pull down on filter tabs and lift filters out.
Set filters aside.
3. Remove bottom cover from hood. Set cover and mounting screws aside.
Bottom Cover
(Held in place with 2 screws)
Filters
7” Round Duct Plate
Preparing Hood

English
6
4. Remove Damper/Duct Connector from inside the hood. Set connector aside
with mounting screws and parts bag.
5. Remove the appropriate electrical knockout by inserting a screwdriver. Then
snip or break the attachment points.
6. Remove either top or back wiring knockout and install approved electrical
conduit according to national electrical code.
Damper/Duct
Connector
Conduit

English
7
Non-Ducted Installation - Skip to “Preparing Electrical Connections”
section. The following steps (7 thru 15) are for DUCTED INSTALLATION
ONLY.
7. Remove Light Panel - held in place with (3) #8 screws and (2) #8 screws.
Disconnect light assembly wire harness (white connector).
8. Remove Air Chute - held in place with one (1) screw.
NOTE: Be careful not to disconnect any wires.
9. Remove Baffle from air chute.
10. Rotate and reinsert baffle into air
chute (as shown) so that the baffle
tabs fit all the way into slots in the
air chute. An audible “click” will
be heard when fully installed.
BAFFLE
SLOTS
BAFFLE
TABS
Light Panel
(3) #8 Screws
(2) #8 Screws
BAFFLE
SLOTS
BAFFLE
TABS
Air Chute
BAFFLE
SLOTS
BAFFLE
TABS
SUPPORT FIN

11. Re-install air chute, re-connect wire harness, and replace light panel.
NOTE: Be careful not to trap wires between support fin and light panel.
12. Remove appropriate Duct Knockout(s) from top or back of hood.
13. Horizontal Discharge Only: Remove the Plate in front of the horizontal
discharge knockout. Cut the Ties, remove the screw(1) located on top of
unit, lift plate out, and discard plate. DO NOT REMOVE the Metal Strip
held in place with Screws(2).
English
8
TOP RECTANGULAR DUCT KNOCKOUT
(Remove for 3¼” x 10”Vertical & for 7”Round Discharge)
SEMI-CIRCULAR DUCT KNOCKOUT
(Remove for 7”Round Discharge)
SEMI-CIRCULAR DUCT KNOCKOUT
(Remove for 7”Round Discharge)
TOP RECTANGULAR DUCT KNOCKOUT
(Remove for 3¼” x 10”Vertical & for 7”Round Discharge)
SEMI-CIRCULAR DUCT KNOCKOUT
(Remove for 7”Round Discharge)
SEMI-CIRCULAR DUCT KNOCKOUT
(Remove for 7”Round Discharge)
TIES
PLATE
METAL STRIP
SCREWS(2)
SCREW(1)
(
C
120 VA
HOUSE
WIRING
C)
CARDBOARD
(Use to protect
cooktop)

English
9
14. 3¼” x 10” Ducted Discharge Only: Remove Tape from damper flap and
attach Damper/Duct Connector over knockout opening with screws removed
in Step 4 under PREPARING HOOD.
Make sure damper Pivot is nearest to Top/Back Edge of hood.
15. 7”Round Ducted Discharge Only: Re-install 7 ”Round Duct Plate removed
in Step #1 under “PREPARING HOOD” section. Install a 7” round damper
(purchase separately). Damper flap must open freely in direction of airflow
(away from range hood).
NOTE: To accommodate off-center ductwork, the Damper/Duct
Connector can be installed up to 1-inch on either side of hood
center or the 7” Round Duct Plate can be installed up to ½” on
either side of hood center. In extreme off-center installations, one
end of the duct connector may need to be trimmed to clear the
electrical cable clamp.
UP TO 1”SIDE-TO-SIDEADJUSTMENT TAPE TOP/BACK EDGE
DAMPER/DUCT
CONNECTOR (Vertical
discharge position shown)
PIVOT