Haier HWM70-928NZP User manual

Double Drive
Fully Automatic Washing Machine
User’s manual
HWM70-928NZP
HWM80-928NZP
Please read this manual carefully before using.●
Retain it for future reference.●

2
Names of the parts ...................................................................3
Safety precautions ....................................................................4
Installation and adjustment .......................................................6
Install the water inlet hose ........................................................9
Preparation before washing ....................................................11
Put in the laundries .................................................................12
Use the operation buttons.......................................................13
Disposal after washing............................................................17
Trouble-shooting answer to question ......................................18
Packing List ............................................................................19
Specifications .........................................................................19
Contents

3
Names of the parts
Meaning and description of the symbols
20
Water absorption gasket
21
Power cord
22
Back cover
23
Fixed foot
24
Screw cover
25
Cabinet handle
Drain hose
1Top lid component 10
Inner cover
2Detergent box 11
Inner tub
5Softener inlet
12
Outer tub cover
4Balance ring
7
Control panel seat
3Hook
13
Filter cover
16
Pulsator
14
Lint filter
615
Front control board
18
Adjustable foot
17
Cabinet
9
Adjustable foot label(2 pieces)
8
Base frame
19
Water inlet valve
18
19
20
21
22
23
24
25
3
17
15
8
12
13
14
16
7
Warning sign Contents marked with that symbol are related to the safety of the
product and the personal safety of the users. Please operate in
strict conformity to the contents, otherwise it may cause damage
of the machine or injure the personal safety of the user.
Forbidden sign Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage of the
machine or injure the personal safety of the user.
1
2
5
4
6
9
10
11

4
Safety precautions
Please plug the plug on special
receptacle
with rated voltage. Be sure to use
singlephase three pins receptacle.
Ensure the earthing prong of the power
receptacle is earthed reliably. Use
leakage protector if possible.
The power cord plug should be convenient
to be pluged in or pluged out with hand
while the washing machine runs normally.
Be sure to pull the plug out and close the
water tap when the machine is idle, when
moving the machine, or when cleaning the
machine. Do not use wet hand to insert or
pull out the power plug.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.●
Keep the pin of the power plug clean, if the power plug is polluted with dust,●
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have●
it replaced by the technicians of our special shop or our customer care agent.
In case the washing machine is installed
on ground with carpet, do not block the
ventilation hole with carpet.
Carpet
The ventilation holes
at the bottom
Do not use water hotter than 50 °C .
Do not put the machine at damp place like
the bathroom. Never wash it with water.
Not put wet laundries on the control panel.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose,
do not use the plug any more.

5
Please keep the lint filter in good condition,
and install it to proper position during
washing. If the lint filter is lost or damaged,
please contact the customer
care agent of our company.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
To protect your laundries and washing●
machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before
washing.
Please check if the water faucet is open, and if the connection of the water inlet pipe is●
proper.
It is suggested to use foamless washing powder.●
To change the direction of drain pipe, please contact the customer care agent of our●
company.
Please don’t use the washer in the environment below 0°C; if the washer has been●
stored below 0°C, please be sure to ensure the washer is placed under the room
temperature for 2~4 hours and then use otherwise the washing effects may be
lowered or the washer may be damaged.
Do not put hand into the
rotating tub. It is dangerous
even if the rotation speed is
slow. Take special care of
the children. Keep children
away from the washing
machine to avoid them
climbing on.
Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items (such as
the kettle with hot water) on the washing
machine.
Petrol
Thinner
Install
Dismantle

6
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
1. Open the top lid of the washing machine.
2. Put the inner cover component on the outer tub cover, aiming the inner cover shaft to
the installation hole of the corresponding outer tub cover shaft groove.
3. Firstly insert the inner cover shaft of one side into the corresponding outer tub cover
shaft groove, then push the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position to guarantee there are
no dropping or abnormal sound in opening and closing of the inner cover, and the
operation shall be smooth. Do not dismount the inner cover component after washing.
After you open the package, please lean the washing machine gently down on soft items
(like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of the machine with the eight screws by a cross
screwdriver, then lift the machine up gently. See to the figure:
Install the inner cover component
Install the bottom plate
Outer tub cover
Inner cover shaft Inner cover shaft
Outer tub cover shaft groove Outer tub cover shaft groove
Inner cover component
I enlarged view
II enlarged view
Figure 1 Figure 2
Bottom plate Soft items
Front
Back
Two claws at the bottom
cover shall be inserted in
two bar-shaped holes in
the stand. Make sure the
claws are firmly in place.
Fasten the bottom plate
to base frame with one
screw.

7
The drainage shall be smooth with the drain
hose.
Usage of the drain hose
<10cm
1. The height of the drain hose shall be less
than 10cm, or the drainage will not be
smooth, and cost such long time that the
machine may stop at mid way.
3. If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
4. If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 30 mm, and the length shall
not exceed 1.5 m.
4. If the extra hose is too long, cut it
either at A or at B.
2. Do not step on or press the drain hose.
<1.5m
> 30mm
Adjust the adjustable foot:●
To adjust the washing machine, please first
lift up the front of the machine slightly, then
twist the adjustable foot on the both side.
The largest allowed slope of the
shank base of the machine is 2°. The
slanting or rough ground will result
in unstable running or stoppage of
the machine. Please adjust it with
following methods:
Adjust the installation position
Confirm it’s horizontal:●
Hang the lead line to check if
it is horizontal.
+LJK /RZ

8
How to change the direction of the drain hose
1. Please lean the washing maching gently down on soft items,such as towel, cloth,
blanket, etc.(as indicated in Figure 1)
2. Dismantle the bottom plate.(as indicated in Figure 2)
3. Nip the end of the drain hose and remove the hook of fixing the drain hose.(as
indicated in Figure 3)
4. Put your hand into the washing machine and undraw the drain hose clamp. Extend the
drain hose in other side and fix it with the clamp. (as indicated in Figure 4)
5. Install the bottom plate and the hook of fixing the drain hose.
Figure 1 Figure 2 Figure 3 Figure 4
Take off the
drain pipe clip
HWM70-928NZP
HWM80-928NZP
Remarks: In order to make sure of the correct of installation, it is suggested to change
the direction of the drain hose with our company serviceman.
1.Dismantle the back cover of the washing machine.
2.Press the spring lamination lightly and pull the top
segment of the drain hose decumbent then put
down the drain hose from the drain hose frame.
3.Put down the drain hose, squeeze the drain hose
lightly and take off the hook, put the drain hose into
the cabinet. Take off the small baffle which installed
on the other drain outlet and install it on the side
which won't install the drain hose.
4.Extend the drain hose from the other side and install
it on the base by the drain hose frame
5.Install the back cover.
Back cover
Drain hose frame
Spring lamination

9
Connection between the water inlet hose jointer and the water
faucet
Install the water inlet hose
Confirm the water faucet
Water tap, suitable
Outlet end surface
>10mm
Water tap, not suitable
It is required that the front end shall be longer than 10mm.
The outlet end surface of the tap shall be flat and smooth. If not please file it to avoid
leakage.
Press the lower end of the lock lever and push down the slider. Take off the water inlet1.
hose jointer from the water inlet hose component. See to Figure 1.
Loosen the screw till the water faucet can be accessed. Put the jointer of the water2.
inlet hose on the faucet. See to Figure 2.
(If the faucet is too large and the jointer can not be set on the water faucet, please
loosen the four screws and take out the bushing in the jointer. The front end of the
faucet must be smooth, otherwise it may leak water. See to Figure 3.)
Figure 1
Lock lever
water inlet
hose jointer
Slider
water inlet hose
Figure 2
Screw knife
Sign plate
Figure 3
Screw
Bushing
Fasten the four screws evenly. See to Figure 4.3.
Take off the nameplate. Twist the fastening nut as per the indication of the figure to4.
seal up the exit end face of the faucet. See to Figure 5.
Remarks: Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut.
See to figure 6.
Figure 4 Figure 5
Nut
Figure 6
About 4mm before twisting
About below 2mm after twisting

10
Do not take off the water absorption cushion.1.
Please check if the cushion is dropped or
damaged before each usage. If it happens
please contact our after-sale department
immediately.
Put the nut of the water inlet hose on the valve2.
jointer.
Fasten the nut. Swing it gently to confirm if it’s suitable.3.
Push down the slider. Insert the water inlet hose into1.
the jointer.
Hang the lock lever to the jointer.2.
Release the slider till a click sound is heard.
Connection between the water inlet hose and the
washing machine
Connection between the jointer of the water inlet hose and the
water inlet hose
Jointer of the water
inlet hose
Slider
Locking lever
Nut of the water inlet hose
Water absorption cushion
Jointer of the water inlet valve
Swing the hose gently to confirm if it is fastened1.
stable.
After installation, open the tap to check if it leaks.2.
Do not bend the hose with overstrain.3.
Before each usage please check if the connection4.
between the jointer of the water inlet hose and the
water tap, and the installation of the water inlet hose
are firm, so as to prevent dropping from improper Installation position.
Close the water faucet.1.
Press the locking lever. Push down the slider. Then pull off the2.
water inlet hose. If the machine is used more than once every
week, the jointer of the water inlet hose can be kept on the tap to
prevent damaging the fixing screw.
Check the connection between the jointer of the water inlet
hose and the water faucet
Dismantle the water inlet hose
Locking lever
Slider
The new hose-sets supplied with the appliance are to be used and
that old hose-sets should not be reused.