Haier HWM75-78 User manual

User's manual
This manual is for
HWM75-78
Please read this manual
carefully before using.
Retain it for future reference.
Full automatic washing machine

Contents
Names of the parts
Safety precautions
Trouble shooting
Packing list Specification
Installation and adjustment
Usage of the drain hose
Preparation before washing
Put in the laundries
Usage of the detergent
Use the operation buttons
Installation the water inlet hose
Disposal after washing
*
Finish washing
Close the top lid
Answers to question
*

Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
Warning sign
Names of the parts
Meaning and description of the symbols
Forbidding sign
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damageof the machine or injure the
personal safety of the user.
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Control panel
Outer tub cover
Lint filter
Balance ring
Inner tub
Attachment block
Cabinet
Liquid whitener inlet
Fixed leg (3 pieces)
Adjustable leg
Detergent box
Top lid component
Inner cover component
Pulsator
Water inlet valve
Water absorption
cushion
Round cover
Front control board
Cabinet handle
Drain hose
Back cover
Power cord
Cabinet base
Adjustable foot
seam

Safety precautions
Please insert the power cord into
special receptacle with rated vol-
tage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
Do not use water hotter than 50 C .
In case the washing machine is in-
stalled on ground with carpet, do not
block the ventilation hole with carpet.
The ventilation holes
at the bottom
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
Earth

Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Petrol
Thinner
To protect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
It is suggested to use foamless washing
powder.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged,please contact the local
after-sales service department of our company.
The back cover of lint filter
The front cover of lint filter
install
dismantle

Installation and adjustment
Please install and adjust the machine according to the requirement of the mannual.
It is very important to your security and correct operating the machine.
After opening the package, please lean the washing
machine gently down on soft items (like towel cloth,
blanket, etc.). Install the bottom plate to the bottom of
the machine with eight screwsby a cross screwdriver,
then lift the machine up gently. See to the figure:
Install the inner cover component
Install the bottom plate
Inner cover
Inner cover shaft
Outer tub cover
Section •enlarging
Push
Outer tub cover
shaft groove
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer
tub cover, aiming the inner cover shaft to
the installation hole of the corresponding
outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the
corresponding outer tub cover shaft groove, then push
the another inner cover shaft into the corresponding
outer tub cover shaft groove. Please install to designated
position to guarantee there are no dropping or abnormal
sound in opening and closing of the inner cover, and the
operation shall be smooth. Do not dismount the inner
cover component after washing.
Soft object
Bottom plate
Back
Screw
Front

The washing machine away from wall should be overrun 20mm. The largest allowable slope of the
shank base of the machine is 1 .The slanting or rough ground will result inunstable running or
stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
Adjust the Installation position
Fasten
Loosen
High Low
the adjustable nut
the adjustable feet
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 .After adjustment, fastenthe nut.
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
Do not step on or press the drain hose.
If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
If the extra hose is too long,cut it either at A or at
B point.
AB
<10cm
A
> 30mm
<1.5m
If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
Usage of the drain hose