HAISEN HD06VCRH 3 User manual

This figure indicates the maximum distance at the highest mounting height with 100% sensitivity.
Detection coverage
Typical installation height 15m
PLUG & PLAY
HD06VCRH 3
Haisen Technology | 01Specifications subject to change without notice.©All rights reserved.
Technical data
Dimensions (Unit: mm)
1. Automatic On/off control with
Daylight sensor.
2. Optional detection range, holdtime ,
daylight threshold, Stand-by period and
Stand-by dimming level.
3. Remote control setting.
4. 5 year warranty.
15m
10-15M
Highbay
Daylight
threshold
Stand-by
period
Stand-by
dimming level
Hold
time
Detection
area
On/off
control
Remote control
setting
5
years
2 3 4 5 623456
Ceiling Mounted
2
4
6
8
10
12
14
16
Mounting
height
Wall Mounted
2 4 6 8 10 18161412
1
2
3
4
1
2
3
4
CoveredWell covered
Mounting
height
Detection area
DIM 0-10V
10%/20%/30%/50%
Max,ø14m/45.92ft (ceiling mounted)
15m/49.2ft (ceiling mounted)
Operating voltage
Operating current
Output
Stand-by power
Hold time
Daylight threshold
Stand-by period
Stand-by dimming level
5.8GHz±75MHz
<0.3mW
Microwave frequency
Microwave power
Mounting height
Detection range
0.5~1.5m/s
Operating temperature
IP rating
10-15VDC
30mA±5%
IP65
Motion detection
-20°C~+60°C
Warranty 5 years
2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable
25%/50%/75%/100%
5s/30s/1min/3min/5min/10min/20min/30min
LED Driver
Red: 12V
Grey: GND
Purple: DIM
DIM GND 12V
ø50
50
24
12
22.5
Wiring diagram
Factory Default Setting: Detection area 100%/ Hold time 5s/ Daylight threshold Disable/Stand-by
period 0s/Stand-by dimming level 10%.

Plug & Play
Haisen Technology | 02
Shenzhen Haisen Technology Co., Ltd., Tel: [phone] 丨Fax: [phone]丨Email: [email protected] 丨www.haisensz.com
Light off when ambient
lux level is higher than
preset lux amount.
Light automatically on
when ambient
brightness is lower
than preset lux level.
With insufficient
ambient brightness,
light dims to 100%
when motion
detected .
Light dims to
standby level if no
motion detected after
holdtime.
Application____Daylight priority
Daylight Priority
+
Base
Sensor Module
Empty Cover
Motion sensor
Motion sensor
No sensor
No sensor
+
The bottom part will be alwaysonthe lighting fixtures; ifthe functionis needed, the
module will be placed inside; if no function needed, the module will be removed. It
doesn't hurt the looking ofthe whole pack.
Icon No icon
The cover with humanoid iconindicates
there isbuilt-in microwave module with
sensor function; The cover without
humanoid iconindicatesthere is no
built-in module aswell as sensor
function.
Natural light
Lux off
Lux on
light on automatically light off automatically
Precondition of Daylight priority:
2. Standby dimming level is on 10%, 20% or 30%;
3. Daylight threshold is on 30Lux, 50Lux, 80Lux or 120Lux.
With Daylight priority function, HD06VCRH 3 is able to differentiate artificial light
brightness from natural light after installed inside the fixture, and automatically turn
off light when ambient brightness exceeds preset lux level.
Dusk/Dawn sensor:
Dual-PD technology brings a fully automatic dusk/dawn sensor which can tell the difference between
natural light and LED light, to ensure the light will be off when needed.

Haisen Technology | 03
Shenzhen Haisen Technology Co., Ltd., Tel: [phone] 丨Fax: [phone]丨Email: [email protected] 丨www.haisensz.com
Installation Method
With insufficient
daylight, when motion
detected, light ON.
With sufficient daylight,
even when motion
detected, light remains
OFF.
After the stand-by
period, light OFF.
After last detection, the
light will be dimmed
down to the stand-by
dimming level
(10%,20%,30% or 50%)
after holdtime.
Hold time Stand-by period
3. Function Demo - Dimmable control/Corridor function
Hold time
After the last detection and
the present hold time
elapsed, light OFF.
With sufficient daylight,
even when motion detected,
light remains OFF.
With insufficient daylight,
when motion detected, light
ON.
After people leave the detection
area, light remains 100%
brightness within hold time.
When motion is detected,
the sensor will switch on the
light to 100% brighteness.
After the last detection and
the present hold time
elapsed, light OFF.
1. Automatically ON/OFF function:
Light on when detect movement and off after people leave at night. Applications: Corridor, Staircase.
1
2
1
2
3
2. No daylight function
The daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off
after stand-by period .
Applications: Dim places such as Basement Parking, Underpass.

Attention
Haisen Technology | 04
Shenzhen Haisen Technology Co., Ltd., Tel: [phone] 丨Fax: [phone]丨Email: [email protected] 丨www.haisensz.com
1. Please read the instructions carefully before using this product and keep it well
for all users to read at any time.
2. The sensor should be installed by qualified electrician and ensure power is off
before the installation.
3. We reserve the right to modify any incorrect text, image and necessary technical
parameters.
4. Any unauthorized modification is forbidden, otherwise all guarantees will be
immediately invalid.
1. Microwave sensor can be installed in any lamp except the one with full metal shell.
2. The detected surface cannot be shielded by metal objects.
3. Make sure the microwave module is completely exposed outside.
4. The detection surface of the sensor module shall be installed facing the detection area.
5. Should be kept away from the driver to avoid interference generation and lamp flashing.
6. Wiring must be strictly in accordance with the wiring diagram to avoid short circuit.
Installation precautions
1. Suitable for indoor installation to avoid false triggering due to external factors such as rain, wind or
tree swing.
2. Shall not be installed in the place with all four metal shelters and small space (such as
galvanized-iron roof ).
3. Shall note be mounted installation, so as to avoid false trigger caused by the lamp itself shaking.
4. Shall not be installed next to large operating machines such as ventilator/ceiling fan to avoid false
triggering caused by machine vibration.
Application Environment
1.Microwave can penetrate walls or glass thinner than 20cm and attenuate if thicker than 20cm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting height and movement volume.
4. Conduct test on sunny days without the lampshade which will affect the tested lux value.
User Notes
HD03R
Reset
Auto Mode
Detection area (Press to define detection area 100%/75%/50%/25%.)
Hold time (Press to define holdtime 5s/30s/1min/3min /5min/10min/20min/30min .)
Daylight threshold (Press to define daylight level 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable.)
Stand-by period (Press to define stand-by period 0s/10s/30s/1min/5min/10min/30min/+∞.)
Stand-by dimming level (Press to define stand-by dimming level 10%/20%/30%/50%.)
1、Press "Reset" button, change brightness to max level.
2、Press “Reset” button, products with DIP switch will be controlled by DIP switches; otherwise all the setting will be just
initial, that is 100% detection range,hold time 5S, no stand-by time and daylight threshold disabled.
Press “Auto Mode” button, the sensor starts to work and all settings remain the same before the light gets switched on/off.
Note: Disable means light will be turned on once sensor detects movement, regardless of the ambient lux.
Note: “0s” means no standby period; “+∞” means unlimited standby period.
The button “Test (2s)” is for testing purpose after commissioning.Pressing this button, the sensor goes to test mode
( hold time is only 2s )
1. "ON/OFF" key only functions as a switch of the light.
2. If press this button to turn off the lamp before it's short-circuited, the lamp will remain off after power-on again.
ON/OFF
Flick after press any button
Start
+/-
Memory
Apply
Test (2s)
Flick only after press "Apply" button
Press "Start" to customize scene, users can change detection range, daylight threshold, holdtime, standby dimming level and
standby period.
1. Press "Memory" to save all the settings.
2. The settings remained as the last time if not get resetted values.
1. Press "Apply" to deliver the saved setting.
2. Press "Apply" without “memory”will make all the setting one-time operation.
3. Settings should be done within 30S, otherwise it exits memory mode.
1. To adjust brightness 10-100% in on/off mode.
2. To adjust highest brightenss 60-100% in sensor mode.
Remote for dimmable sensors
with memory function

Haisen Technology | 05
Shenzhen Haisen Technology Co., Ltd., Tel: [phone] 丨Fax: [phone]丨Email: [email protected] 丨www.haisensz.com
HD03R Instruction
Memory & Apply Mode
1. Press "ON/OFF button" to turn on the light or off.
2. To reset the parameters, Please follow the steps as below:
Step 1 - Press ON, to turn on the light if it was off at the start.
Step 2 - Press "Start" to the well-setting sensor.
Step 3 - Press the button of Detection range, Hold time, Stand-by dimming level, Stand-by period and Daylight threshold one aft
other in sequence.
Step 5 – Press “Memory” to memorize the settings.
Note: The interval of each parameter setting shall be controlled within 30s.
Isolated Setting Mode
1. Press "ON/OFF button" to turn on the light or off. Press "Auto Mode", the remote will activate settings that were saved last
remain at the factory default settings.
2. To reset the parameters, Please follow the steps as below:
Step 1 - Press ON, to turn on the light if it was off at the start.
Step 2- Press any button of "Auto Mode", “Reset” , Test" and "Apply" to begin the sensor detection mode.
Step 3 - Press the button of Detection range, Hold time, Stand-by dimming level, Stand-by period and Daylight threshold one aft
other in sequence.
3. To programme other lights in the array that have similar sensors to the same programme.
Step 1 - Press "ON" to the second sensor
Step 2 - Press "Apply"
Notes:
1. Settings will be saved automatically and remain until you press reset again.
2. Light will flicker when setting each parameter.