Hakko Electronics FT-720 User manual

Thank you for purchasing the HAKKO FT-720.
This product is a rotating tip cleaner.
Before using this product, be sure to read this manual.
Keep this manual readily accessible for reference.
1. Contents and Part Names Conrm the contents before use.
HAKKO FT-720.................. 1
AC Adapter ........................ 1
Instruction Manual
(this document) .................. 1
15 10
25 20
Base
Solder Waste
Collector
P.W.B. Cover
Opening Size
Adjuster
Opening Size
Pulley Belt
Cover
AC Adapter
Sensor
Cover
P.W.B. Cover
Adjuster
The applied tip is introduced
on the website.
https://www.hakko.com
2. Specications
●HAKKO FT-720
Rating 24 VDC 140 mA
Brush
rotational
speed
1670 rpm
Dimensions
67 (W) × 63 (H) × 94 (D) mm
(2.6 × 2.5 × 3.7 in)
Weight 200 g
●AC Adapter
Output
voltage 24 VDC
* This product is applied with
electrostatic countermeasures.
* Please note that specifications and
appearance are subject to change
without notice in the interest of
product improvement.
CAUTION
■ Handling precautions for ESD Safe products
This product contains electrostatic countermeasures, so please use the
following precautions:
1. Not all plastic parts are insulators, they may be conductive. Be careful not to
expose live electrical parts or damage insulating materials when performing
repairs or replacing parts.
2. Be sure to ground the product before use.
TIP CLEANER
FT-720
Instruction Manual
※ 各言語（日本語、英語、中国語、フランス語、ドイツ語、韓国語）の取扱説明書は
以下の URL、HAKKO Document Portal からダウンロードしてご覧いただけます。
（商品によっては設定の無い言語がありますが、ご了承ください。）
* 各國語言（日語、英語、中文、法語、德語、韓語）的使用説明書可以通過以下网
站的 HAKKO Document Portal 下載參閲。
（有一部分的產品沒有設定外語對應、請見諒）
* Instruction manual in the language of Japanese, English, Chinese, French,
German, and Korean can be downloaded from the HAKKO Document Portal.
(Please note that some languages may not be available depending on the product.)
https://doc.hakko.com
3. Warnings, Cautions, and Notes
Warnings, cautions, and notes are placed at critical points in this
manual to direct your attention to signicant items. They are dened
as follows:
WARNING:
Failure to comply with a WARNING may result in
serious injury or death.
CAUTION:
Failure to comply with a CAUTION may result in injury
to the operator, or damage to the items involved.
Note: This indicates procedures or information that are
important in a process described in this document.
Be sure to observe the following precautions to ensure safety.
WARNING
● Those without the permission of a
manager and those without the required
experience or knowledge (including
children) are not allowed to use this
product.
● Do not allow children to play with this
product.
● Do not allow children to clean or
perform user maintenance without
supervision.
Failure to observe the following precautions to ensure safety might result in
electric shock, malfunction or other trouble.
CAUTION
● Before using this product, fully read all descriptions in this
document.
● Do not use this product as an iron stand.
● Be sure to install the solder waste collector before use.
● Be sure to attach the P.W.B. cover and sensor cover before
use.
● When carrying the cleaner, carrying it by holding the base
and not the AC adapter plug.
● This product is for indoor use only. Do not use it outdoors.
● When this product is not used for a long time, or before
repairing or cleaning this product, disconnect the AC adapter
plug from the power outlet.
● When replacing parts, use only genuine HAKKO parts.
● Use only the AC adapter that is included in the set. Do not
use other AC adapters.
● Do not modify this product.
● When inserting and removing the plug, hold the plug body
and do not pull the cord.
● Do not allow this product to get wet. Also, do not handle it
with wet hands.
● Do not perform any other actions that may be considered
dangerous.

2020.11
MA03201Jb201116
© 2020 HAKKO Corporation. All Rights Reserved.
Please access the web address below for other distributors.
https:// www.hakko.com
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL: [phone] FAX: [phone]
https:// www.hakko.com E-mail: [email protected]
4. Operation
(1) Insert the AC adapter plug in the DC jack.
(2) The sensor reacts when the tip is inserted and cleaning will begin.
Note Do not intentionally rotate the brush continuously.
Note Remove the adjuster when using a large tip. The adjuster
can be stored in the base.
Note This product cleans the tip in a short time. If the tip is left
in for a long time, it may accelerate deterioration of the tip
or the cleaning brush.
Note Place this product on grounded surface with electrostatic
measurement, or connect a wire to the ground screw
upon use.
Ground Attachment Part
Adjuster
5. Maintenance
CAUTION
Regularly remove solder waste and ux residue that adhere to the
solder waste collector, cleaner interior, and cleaning brush.
Note To remove the cover you must rst remove the AC
adapter plug from the DC jack.
● Removal of Solder Waste
Remove the cover and
remove solder waste. Solder Waste
● Replacing the Brushes
Replace the cleaning brushes by pulling them straight out of
their brush xing shafts.
* Tools are not required.
Brush xing shaft
● Cleaning the Sensor Cover
Remove stains on the upper and lower recess areas of the
P.W.B. cover using a soft brush.
Recess
Note If the sensor cover is considerably stained, remove the
sensor cover and clean it with alcohol damp cloth. In this
case, be careful not to let solder waste or other debris fall
into the device.
Note Replace the sensor cover if it has cracked or there is a
considerable amount of scratches.
6. Troubleshooting
The cleaning brush
continues to rotate.
Is the P.W.B. cover
or adjuster bent or
out of alignment?
Attach it in the
correct position.
Is the sensor cover
stained? Please clean it.
The motor does not
move.
Are the AC adapter
and plug connected? Connect.
The motor moves but the
cleaning brush does not rotate.
Has the pulley belt
come off? Reattach it.
When other problems occur or the above remedies do not resolve
a problem, contact your nearest agent.
7. Parts List
● Replacement Parts
Part No. Part Name Specications
A5063 Cleaning brush C Fluoroplastic brush, qty 2
A5060 P.W.B. cover With sensor cover
A5061 Adjuster
A5062 Sensor cover qty 10
B5284 Pulley belt
B3528 AC adapter Flat pin plug
B5118 AC adapter Chinese plug
B5119 AC adapter BS plug CE
B5120 AC adapter European plug CE
B5121 AC adapter Australian plug
● Options
Part No. Part Name Specications
A1566 Cleaning brush A Plastic brush, qty 2
A1567 Cleaning brush B Metal brush, qty 2