Hakuna Pets Deluxe Aluminium 1162 User manual

Deluxe Aluminium
Pet Door
Product codes:
#1162, #1166, #1167, #1168, #1169, #1170, #1171, #1172
IMPORTANT! READ AND
FOLLOWTHESE
INSTRUCTIONS CAREFULLY
AND KEEPFOR FUTURE
REFERENCE.
INSTALLATION VIDEO

WARNING
Please read these cautions and notes carefully before attempting installation. For
any questions or concerns, contact Customer Support at www.hakunapets.com/help.
If your home has children as well as pets it is important to remember that children can
misuse the pet door and gain access to potential hazards on the other side. You may
contravene municipal laws and be found guilty of an offence if there was a swimming pool
on the other side of the pet door. You are further advised to be very alert to any future
hazards which may occur from time to time on the other side of the pet door such as garden
chemicals or insecticides which, even if only put down for a few minutes, would be danger-
ous to children. Remember that any closing panel or lock provided by Perma Products with
this product is for simple convenience and is certainly not a security device. Furthermore we
will not be responsible or liable for unintended use or misuse. Please remember it is you the
purchaser who must at all times be aware of what you have allowed access to by the
installation of this pet door. Please remain vigilant throughout the life of this product as it is
you the purchaser who is responsible for any oversight this installation creates.
CAUTION
Before you install this door you must check all your building codes or body corporate rules
that could affect the installation of a pet door. You should also check with a qualified builder
or trades person that the installation you intend is suitable and safe within the chosen
location. This is neither a fire door or security door and it is imperative that you the
purchaser consider any risks that may be created both inside and outside after installation
of your pet door. Please remember to consider future risks that could be brought about by
changes elsewhere on your property.
NOTE
Keep these warnings and cautions with any other important documents in your home and
give them to any new owner, tenant or guest so that they too can be made aware of the
responsibilities that come with having a pet door within the premises. Template is to be
used only as a guide, ensure all measurements and alignment is correct.
Ensure the suitability of location before installation of pet door. If installing into a sliding
door, check pet door does not interfere with door operation or any other doors.
WARNINGS

PARTS LIST /TOOLS REQUIRED
A B C
F
E
D
Parts List
A. Inner door frame
B. Outer door frame
C. Locking cover
D. 4 x Metal screws
E. 2 x Partition large
F. 2 x Partition small
Tools Required
- Jigsaw
- Scissors
- Drill with 10mm (3/8”) and
8mm (5/16”) drill bit
- Phillips Screwdriver
- Pencil
- Tape Measure / Ruler
- Duct Tape

Step 1.
Important:
Step 2. Step 3.
INSTALLATION
XX
Glass installation only to be completed by a professional glazier.
Ensure the pet door is suitable for the chosen installation location.
Measure the height (x) from the underside of the dog’s stomach to the floor.
Mark height (x) on door/panel with tape or similar. Adjust if necessary.
Cut out template supplied in box, align
bottom of cut out with height (x) and
trace onto door.
Drill a hole in each of the four inside
corners with a minimum of 10mm
(3/8”) drill bit.
X

Step 4. Step 5.
Using a reciprocating jigsaw, cut out
the opening, cutting along the pencil
outline.
Step 6.
Measure the thickness of the door/panel and add 10mm (3/8”) (x) so the tunnel
protrudes 5mm (3/16”) on each side. If required, cut partitions down to correct size.
Insert outer frame into opening and mark
screw holes. Drill each of the screw
holes using a 8mm (5/16”) drill bit.
INSTALLATION
X

INSTALLATION
Step 7.
Fit all four partitions into outer door frame, use duct tape to secure the corners then
place into opening.
Step 8.
Screw inner door frame into door/panel. Tighten with a Phillips headscrew driver. If
screws protrude, trim using a hacksaw.
WARNING: Over tightening of screws will cause damage. Take care when trimming
bolts to size as cutting on an angle may cause sharp edges or damage to the frame.

Step 1.
Important:
If installing into a sliding door, check pet door does not interfere with door operation
or any other doors.
SECURITY SCREEN INSTALL
XX
Step 2.
Measure the thickness of the door/panel and add 10mm (3/8”) (x) so the tunnel
protrudes 5mm (3/16”) on each side. If required, cut partitions down to correct size.
Take the measurements needed to cut the opening by following Steps 1-3 of the
previous instructions. Using an angle grinder, cut out the opening.

SECURITY SCREEN INSTALL
Step 3.
Fit all four partitions into outer door frame, use duct tape to secure the corners then
place into opening. If the security screen has insect mesh, place a bead of construction
silicon around the internal section of the pet door and on the mesh surface. Apply this
around the cut out in order to hold the mesh in place when both frames are joined.
Step 4.
Insert inner door frame into security screen. If screws protrude, trim using a hacksaw.
WARNING: Over tightening of screws will cause damage. Take care when trimming
bolts to size as cutting on an angle may cause sharp edges or damage to the frame.
Outside Inside

LOCKING SECURITY PANEL
Step 1.
You can control your pet’s access using the locking security panel. Simply slide the
panel into the channel on the inside frame until latch clips over the bottom of the frame.

GLASS DOOR INSTALL
Refer to Steps 1 and 2 of “Installation”. Place a bead of construction silicon around the
internal section of the pet door and on the surface around the cut out to provide a
weather seal. Tunnel partitions will need to be cut to size as per Step 6 of “Installation”.
Insert the inner and outer frame into the cut out and clamp tightly together.
Please note the screws provided will not be required for this installation.
Step 1.
Important:
Step 2.
Contact a professional glazier to cut out the opening for the pet door. If installing into a
sliding door, check pet door does not interfere with door operation or any other doors.

1. Loosen screws on flap holder. 2. Adjust flap up or down to desired height,
for less noise or magnet strength adjust the
flap to a higher position.
FLAP ADJUSTMENT & REPLACEMENT
3. Ensure flap is parallel with lower frame. 4. Tighten flap holder screws.
1. Loosen screws on flap holder. 2. Use a flat blade screwdriver to pry open
the flap holder.
3. Replace flap and close flap holder, press
until you hear a click.
4. Adjust flap to desired height and tighten
screws.
Flap Adjustment
Flap Replacement

Before starting your training, assess whether your dog would be more motivated to
come inside through the pet door or go outside through it. If your dog loves being
inside the house, you should start this training with them outside. If they’re always
excited to get outside, start with them inside the house.
1. With your dog on one side of the pet door and you on the other, lift the flap of the pet
door all the way up and call them, using an excited voice. Hold treats or your dogs favourite
toy so they can see them on the other side of the pet door. Reward any attempt to come
towards or through the door with lots of verbal encouragement, but don’t let them have the
treat until they make it the whole way through. If your dog is hesitating or nervous to
approach after trying this step, take a break and come back to it later.
2. When they come all the way through, praise and reward them. Then, leaving them where
they are, go to the other side of the pet door, lift the flap and repeat the same exercise. Do
a few repetitions going each way, then take a break. This training can be both stressful and
exciting for your dog, so you should do short sessions to avoid burning them out or causing
them to become distressed.
3. After your dog has had a break, repeat the exercise. If they’re coming through with no
hesitation, repeat the exercise holding the flap up only halfway. Your dog may be distressed
by feeling the flap touching them, use lots of verbal encouragement to guide them through
the door and reward them if they do go all the way through.
4. Once they’re going through with the flap halfway up, continue doing short sessions with
them, gradually lifting the flap up less and less, until your dog is pushing through the door
on their own.
5. Now try to get them to do it on their own. You can do this by leaving them on one side of
the door and scattering some treats or leaving their favourite toy on the other side of the
door. Repeat this for a few sessions until your dog goes through without any verbal
encouragement or reward.
TRAINING

Congratulations! You have made an excellent choice of this quality product. Our commitment to quality also includes
our service. Should you, contrary to expectations, experience defects due to manufacturing faults, we will provide you
with a warranty against defects as follows:
WARRANTY
The product is guaranteed to be free from defects in workmanship and parts for a period of 1 year from the date of
purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or
refunded at our discretion. The benefits conferred by this warranty are in addition to all rights and remedies in respect of
the product that the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
PROOF OF PURCHASE
This warranty is valid for the original purchase and is not transferable. Please keep your purchase docket, tax invoice
or receipt as the best proof of purchase, and as proof of date on which the purchase was made.
EXTENT OF WARRANTY
This warranty is limited to defects in workmanship or parts. All defective products or parts will be repaired or replaced.
This warranty does not cover consumable items.
NORMAL WEAR AND TEAR
This warranty does not cover normal wear and tear to the products or parts.
EXCLUSIONS
This warranty does not cover:
- Any defects caused by an accident, misuse, abuse, improper installation or operation, lack of reasonable care,
unauthorised modification, loss of parts, tampering or attempted repair by a person not authorised by the
distributor.
- Any product that has not been installed, operated or maintained in accordance with the manufacturer’s operating
instructions provided with the product.
- Any product that has been used for purposes other than domestic use.
TO MAKE A CLAIM
If a defect in the goods appears within 1 year, you are entitled to claim a warranty.
Please contact after sales support via the link below:
www.hakunapets.com/contact-us
Please ensure that you have a copy of proof of purchase so that we are able to respond as quickly and
efficiently as possible.
WARRANTYCERTIFICATE

Thankyou !
Providing our customers with a positive experience
is our #1 priority and we value your feedback.
If you have anything less than 5 star
satisfaction or you require any assistance
with spare parts please contact us directly at:
www.hakunapets.com/contact-us
for making a purchase
with Hakuna Pets.