HALNy HLE-3GM User manual

HALNy HLE-3GM Quick Installation Guide
1
Quick Installation Guide
HALNY HLE-3GM

HALNy HLE-3GM Quick Installation Guide
2
Safety Guidance
1.1 Safety Check
Before installing the device, you must check the following items.
1.1.1 Electric Safety
⚫Ensure that there are no inflammable, conductive or moist objects around.
Check whether the cables are aged and whether other electrical appliances
are placed stably,
⚫Check whether the alternating or direct input current is within the allowed
range of the device, whether the polarity of the direct current is correct, and
whether the earth line is properly connected.
1.1.2 Device Position
⚫Because the running electric device easily generates heat, please ensure to
place the device in a well-ventilated environment,
⚫Avoid direct sunshine, and do not place the device on a PC case,
⚫Keep the device away from heat and water,
⚫Check whether power supply is available. The input voltage fluctuation range
must be smaller than 10%. The power plug should not share one socket with
a hair drier, an iron or a refrigerator.
1.2 Safety Caution
⚫Read the quick installation guide carefully before using the device,
⚫Note all Cautions in the quick installation guide,
⚫Do not use any accessory that does not belong to the device without prior
consent of the manufacture, as it may cause fire or product damage,
⚫Use the power adapter accompanied in the package,
⚫Do not place any object on the device,
⚫Keep the device dry, ventilated, rainproof, and clean,

HALNy HLE-3GM Quick Installation Guide
3
⚫During lightning weather, unplug the power plug and all connection cables, to
protect the device against lightning,
⚫Clean the device using a soft and dry cloth rather than liquid or atomizers.
Power off the device before cleansing it,
⚫Power off the idle device,
⚫Keep the ventilation hole clean and prevent any object from dropping into the
device through it. Otherwise, it may cause short circuit and further cause
device damage or fire. Do not spray liquid on the surface of the device,
⚫Do not open the case of the device, especially during device power-on,
⚫Before plugging or unplugging the power, ensure that the power is off, thus
avoiding surge,
⚫Be careful when unplugging the power, as the transformer may be very hot,
⚫Cover the optical interface with fiber interface cap when it is not in use. Avoid
direct eye exposure to the laser emitted from the optical interface. Wear safety
glasses if possible, to protect your eyes.
Caution:
Please read the above safety guidance carefully before device use.
Users should assume responsibilities for any accidents due to
incompliance with the above instructions.
2 Overview
This chapter mainly describes functions and the structure of the HALNy HL-3GM.
2.1 Features and Function
⚫Fast data rate. Support up to 1Gbps downstream/upstream data transmission
rates,
⚫Strong maintainability. Provide various statuses of LED indicators, to help
troubleshooting,

HALNy HLE-3GM Quick Installation Guide
4
2.2 Front and Rear Panel
The description of the front panel and the rear panel of the router as follows.
2.2.1 Front Panel
Fig. 1 - Front Panel
Mesh
Color
Status
Description
Off
Red
On
The power works normally.
Green
On
WAN interface is up and connected with ISP servies
On
Red
Blinking
No connection with mesh controller
Green
Blinking
Connecting to mesh controller
On
Connected to mesh controller
Table 1. LED Indication Table
2.2.2 Rear Panel
Fig 2. Rear Panel
Interface /
Button
Function
LAN
Ethernet interface, for connecting to a computer or an Ethernet interface of a
switch.
WAN
Ethernet interface, for connecting to Wide Area Network
Reset
Press and hold to reset
WPS
Press and hold for 5 seconds to pair device via WPS
Power
Turn on/off power
USB
USB 2.0 port
Table 3.Rear Panel port description

HALNy HLE-3GM Quick Installation Guide
5
3 Router Installation
The chapter describes the required installationoperations before you use the device
for the first time.
3.1 Installation Preparations
The Ethernet interface of your computer connects to the Ethernet interface of the
router. Before installing it, ensure that an Ethernet adapter is already installed in
your computer.
3.2 Connecting device
3.2.1 Connecting the Network Cable
Step 1 Use the one end of the network cable to connect the Ethernet interface of
the computer.
Step 2 Use other end of a network cable to connect the Ethernet interface on the
rear panel of the HALNy HLE-3GM.
3.2.2 Connecting the Power Adapter and Power Cord
⚫Connect the output end of the power adapter included in the device package to
the input end of the power supply,
⚫Insert one end of the power cord attached with the device into the input end of

HALNy HLE-3GM Quick Installation Guide
6
the power adapter. Insert the other end of the power cord into the power socket,
⚫Check whether the Power indicator is on. If it is on, the power supply is normal.
Otherwise, check whether the power cord and the power adapter are correctly
connected.
4 Troubleshooting
Symptom
Solution
The LED indicator is
not on
Check whether the power connection is correct,
Check whether the power adapter matches the
device.
The LED indicator is
red
Check whether your Service Provider have network
problems,
Check whether the network cable is properly
connected to WAN port
5 Technical Specification
Main Technical Specifications
Standard
Ethernet
1000BASE-T
Rate
Uplink
1Gbps
Downlink
1Gbps
Interface
WAN interface
RJ-45 10/100/1000Mbps MDI/MDIX Self adaption
3 LAN ports
RJ-45 10/100/1000Mbps MDI/MDIX Self adaption
WiFi 2.4Ghz
WiFi 5Ghz
802.11n (2T2R MIMO) 300Mbps
802.11ac (2T2R MIMO) 876Mbps
Physical Characteristics and Environment Requirements
Power adapter input
100V～240V AC，50Hz～60Hz
Whole-device power supply
12V DC，1A
Standard power consumption
<12W

HALNy HLE-3GM Quick Installation Guide
7
Main Technical Specifications
Operating temperature
0˚C～45˚C
Operating humidity
10%~90% (non-condensing）
Dimension
L x W x H：305mm x 200mm x 25mm
Weight
<500g
Additional information:
Declaration of Conformity (CE)
This device has been tested and found to comply with the stated standards
which are required by the Council Directive of 2014/30/EU. The device
complies with this CE Declaration when the installation is done in
accordance with the instruction and documentation. The importer don’t take
responsibility for any issues caused by improper use of the device.
The full document is on below web page and it is available in importer:
CE / warranty terms and conditions:
www.halny.com
Importer:
FIBRAIN Sp. z o.o
36-062 Zaczernie 190F (POLAND)
[email protected]
Information furnished by HALNy Networks is believed to be accurate and
reliable. However, no responsibility is assumed by importer for its use, nor
for any infringements of patents or other rights of third parties which may
result from its use. No license is granted by implication or otherwise under
any patent or patent rights of the manufacturer. Manufacturer reserves the
rights to change specifications at any time without notice.

HALNy HLE-3GM Quick Installation Guide
8
Recycling This product bears the selective sorting
symbol for Waste electrical and electronic
equipment (WEEE). This means that this product
must be handled according to European directive
2012/19/EU in order to be recycled or
dismantled. This will minimize the negative
effects on the environment and human health
resulting from the possibility of the presence in
the equipment substances, mixtures and
hazardous components. A user can give the
product to a competent recycling organization, to WEEE collection points or
to a distributor (in accordance with local regulations).