Halsey Taylor 4410BF User manual

PAGE 1 98643C (Rev. C - 12/15)
4410BF_FTN LK4410BR_FTN
Owners Manual
Model 4410BF
Floor Mounted Tubular Bottle Filler Fountain
4410BF Fountains are among the easiest to install Fountains on the market today. To
assure you install these models easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION
FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER APPLICABLE
CODES. After installation, leave these instructions with the Fountain for future reference.
INSTALLER

PAGE 2
98643C (Rev. C - 12/15)
4410BF_FTN LK4410BR_FTN
1. This fountain is to be mounted on a smooth, at, nished surface with adequate support structure. NOTE: Mounting structure
must be capable of supporting 300 lb. load on fountain.
2. Refer to rough-in for plumbing.
3. Install shut-off valve on water supply. (Valve not furnished)
4. Locate and install fountain using 3/8" minimum fasteners, (Fasteners not furnished).
5. Prior to installing the bottle ller to the arm mount of the fountain, insert the drain tube (Item #6) into the arm tunnel and
adjust drain to lean to the left side of arm when facing button. Install bottle ller to arm being sure drain tube is above
mounting plate of ller. Install mounting hardware to secure ller to fountain.
6. Connect water supply and fountain drain. Connect Bottle Filler water line to regulator with the supplied 3/8" to 1/4" reducing
tting. Water connection and drain must comply with local codes.
7. Turn on water supply and check all connections for leaks.
CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the
inlet water supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line pressures
lower than 20 PSI or higher than 105 PSI is not covered by warranty.
8. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/4" IPS. Contractor to supply waste trap and service stop valve in
accordance with local code.
9. Connecting lines to be made of unplated copper and should be thoroughly ushed to remove all foreign matter before being
connected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste, odor, color,
or sediment problems.
10. Connect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve and
the cooler. Remove any burrs from outside of water line. Push the tubes straight into the ttings until they reach a positive
stop, approximately 3/4" (See Fig. 2). DO NOT SOLDER TUBES INSERTED INTO PLASTIC FITTINGS AS DAMAGE TO
THE O-RINGS MAY RESULT.
INSTALLATION INSTRUCTIONS
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE
BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN
ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.

PAGE 3 98643C (Rev. C - 12/15)
4410BF_FTN LK4410BR_FTN
57"
1448mm
27" 686mm
19" 483mm
36 11/16" 931mm
8" 203mm
27 5/16"
694mm
3" 76mm
37" 940mm
14 9/16"
371mm
10" 254mm
O
O14"
356mm 6- O.500 HOLES
EQUALLY SPACED
ON A O12.00"B.C.
A
C
B
B
LEGEND A = 3/8" O.D. UNPLATED COPPER TUBE CONNECT - SHUT OFF VALVE BY OTHERS B = ACCESS PANEL ( 8" X 10" ) C = REMOVABLE BOTTOM COVER

PAGE 4
98643C (Rev. C - 12/15)
4410BF_FTN LK4410BR_FTN
9 &17
17
17
7
13
17
8 & 17
2
6
7
4
10
16
15
12 & 18
16
3
3
14
13 & 16 11
1

PAGE 5 98643C (Rev. C - 12/15)
4410BF_FTN LK4410BR_FTN
ITEM NO. PART NO.
ITEMIZED PARTS LIST
DESCRIPTION
28955C*
45931C
45832C*
45833C
55996C
66816C
72001843
98532C
98677C
98678C
98679C
98680C
98681C
98682C
98683C
98685C
98686C
P05031
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Cover - Round Plate
Outdoor Bottle Filler Drain Plug
Access Panel
Bottom Cover
In - Line Strainer
Tube - Drain (Arm Only)
Drain Fitting - Slip Ell
Kit - "O" Rings and Fittings
Kit - Gasket
Kit - 1.0 GPM Regulator (BF Only)
Kit - Nozzle
Kit - Aerator
Kit - Bottle Filler Trim
Kit - Push Button
Kit - Plastic Drain
Kit - 4400 Series Hardware
Kit - Bottle Filler Waterway
Aerator
TROUBLE SHOOTING AND MAINTENANCE
ACTUATION OF QUICK CONNECT WATER FITTINGS:
Fountain is provided with lead-free connectors which utilize and o-ring water seal. To remove tubing from the tting,
relieve water pressure, push in on the gray collar while pulling on the tubing. (see Fig.2) To insert tubing, push tube
straight into tting until it reaches a positive stop, approximately 3/4".
PRINTED IN U.S.A.
Halsey Taylor – halseytaylor.com
Elkay – elkay.com
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816
2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
*select color option to complete part number
*FINISH COLOR OPTIONS – Choose color option to
complete your model number, add as sufx example:
4410BFEVG
Matte nish: Evergreen = EVG
Gloss nish:
Beige = BGE Gray = GRY Terracotta = TER
Black = BLK Orange = ORN White = WHT
Blue = BLU Purple = PUR Yellow = YLW
Brown = BRN Red = RED
FIG. 1 FIG. 2
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C
1/4” O.D. TUBE
WATER INLET
TO COOLER
3/8” O.D. TUBE CONNECT
COLD WATER SUPPLY
BUILDING WATER
INLET
NOTE: WATERFLOW
DIRECTION
SERVICE STOP
(NOT FURNISHED)