Halsey Taylor HRFG-ER User manual

PAGE 1 97878C (Rev. B - 11/04)
HRFG - ER*B HRFG - SR*B HRFG - SER*B
Halsey Taylor Owners Manual
Refrigerated Marblyte Fountains with Back Panel
HRFG - ER HRFG - SR HRFG - SER
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION
FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES.
After installation, leave these instructions inside the fountain for future reference.
Installer
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO
A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE
IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER
MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE
OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 2
OPERATION OF QUICK CONNECT FITTINGS
FIG. 1
NOTE: WATER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY

PAGE 297878C (Rev. C - 02/18)
HRFG - ER*B HRFG - SR*B HRFG - SER*B
3 1/8 "
79mm
1 1/8 "
29mm
"B" "A" 5 5/8 "
143mm
9 3/8 "
238mm
BACK WALL LINE
WALL LINE
12 "
305mm
MINIMUM
DEPTH
"C"
37 1/4 "
947mm
(HRFG-SR)
31 1/4 "
794mm
(HRFG-ER)
4 1/2 "
114mm
3 1/2 "
89mm
11 "
279mm
1 "
25mm
ELECTRICAL
INLET
27 "
686mm
(HRFG-ER)
ADA
REQUIREMENT
33 "
838mm
(HRFG-SR)
33 1/2 "
851mm
(HRFG-ER)
39 1/2 "
1003mm
(HRFG-SR)
18 3/16 "
462mm
13 7/8 "
352mm
FIG. 3
HRFG-ER/SR ROUGH-IN
LEGEND:
A = 1/4" O.D. TUBE WATER OUTLET
B = 3/8" O.D. TUBE WATER INLET
C = 1-1/4" O.D. WASTE TUBE (NOT INCLUDED)
FINISHED FLOOR

PAGE 3 97878C (Rev. B - 11/04)
HRFG - ER*B HRFG - SR*B HRFG - SER*B
1 1/8 "
29mm
3 1/8 "
79mm
18 3/4 "
476mm
5 5/8 "
143mm
9 3/8 "
238mm
"A"
"B"
12 "
305mm
MINIMUM
DEPTH BACK WALL LINE
"C"
13 7/8 "
352mm
18 3/16 "
462mm
37 1/4 "
947mm
31 1/4 "
794mm
3 1/2 "
89mm
4 1/2 "
114mm
11 "
279mm
1 "
25mm
ELECTRICAL
INLET
27 "
686mm
ADA
REQUIREMENT
33 1/2 "
851mm
39 1/2 "
1003mm
WALL LINE
FIG. 4
HRFG-SER ROUGH-IN
LEGEND:
A = 1/4" O.D. TUBE WATER OUTLET
B = 3/8" O.D. TUBE WATER INLET
C = 1-1/4" O.D. WASTE TUBE (NOT INCLUDED)
FINISHED FLOOR

PAGE 497878C (Rev. C - 02/18)
HRFG - ER*B HRFG - SR*B HRFG - SER*B
INSTALLATION INSTRUCTIONS
1. Install remote chiller. Remove front panel of chiller. Remove and discard cardboard inner pack from
between compressor and side panel. Slide chiller onto the shelf and position it to the left within the guides on
the shelf. NOTE: Building construction must allow for adequate air ow on both sides, top, and back of chiller.
A minimum of 4" (102mm) on both sides and top is required. See chiller instructions for additional instructions.
2. Make water supply connections. The inlet port is marked on the chiller (1/4" O.D. copper tube). Bend the
copper tube (provided) at an appropriate length from chiller to opening in frame. Install the in-line strainer
(provided with chiller) by pushing it in until it reachs a positive stop, approximately 3/4" (19mm) on the marked
chiller inlet port. Attach an unplated and deburred copper water inlet line and a service stop (not provided) to the
in-line strainer. Turn on the water supply and ush the line thoroughly. DO NOT SOLDER
TUBES WHILE INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT.
3. Hang the upper panel on the mounting frame hanger. Align holes in the panel with the holes in the mounting
frame. Be sure that panel is engaged with hanger at top of frame before releasing it.
4. Install fountain. Remove access cover plate on underside of fountains and save the screws. Mount the
fountains to the upper panel and the wall frame with (4) 5/16" x 1-1/4" (32mm) long bolts, washers, and nuts.
Tighten securely, but do not overtighten. Over tightening will crack the Marblyte Fountain.
NOTE: The short fountain should be mounted to the upper left hand side of the panel.
5. Remove elbow from end of p-trap and attach it to drain tube. Re-attach elbow to p-trap and cut waste tube to
required length using plumbing hardware and trap as a guide.
6. Make connection between remote chiller outlet tube and fountain(s). Outlet port is marked on the chiller (1/4"
O.D. copper tube). Install a 1/4" union/tee (provided) on the marked chiller outlet port. Insert the 1/4" poly tubing
coming from the fountain(s) into the union/tee. Turn on water supply and check for leaks.
DO NOT SOLDER TUBES WHILE INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS MAY
RESULT. (See gure 5 or 6).
7. These products are designed to operate on 20-105 PSI supply line pressure. If inlet pressure is above 105 PSI,
a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting these
products to supply line pressures lower than 20 PSI or higher than 105 PSI is not covered by warranty.
8. Make electrical connections to the chiller. See chiller instructions.
9. Check stream height from bubbler. Stream height is factory set at 35-40 PSI. If supply pressure varies greatly
from this, adjust the screw on regulator item 2 by using a small screwdriver through the small hole in the push
button item 5 (See Fig.8). Clockwise adjustment will raise stream height and counter-clockwise adjustment will
lower stream height. For best adjustment stream height should be approximately 1-1/2" (38mm) above the bubbler
guard (See Figure 7, Page 5).
10. Mount lower panel. Loosen the (2) #10-24 x 5/8" (16mm) screws at frame bottom lip. Slide upper tongue of
lower panel under lower edge of already installed upper panel. Tighten previously loosened screws securely.
11. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
Care and Maintenance of Halsey Taylor Marblyte Fountains
Marblyte provides an exremely durable, nonporous surface which resists staining. Care is very simple. Routine
cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam cleaner, is all that is normally needed
to give many years of trouble free service. Cleaners left standing on the fountain surface can dull the surface nish.
Be certain to rinse all cleaning agents completely and polish with a soft cloth.
Harsh abrasive cleaners are not required and should not be used.
Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple scratches
and stains. Cigarette burns can normally be removed without noticeable effect. Deeper scratches or gouges can be
corrected with ne grit sandpaper (240 grit then 400 grit) or a green Scotchbrite pad.
To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or like products will
keep the nish looking like new.
Orice Assy: Mineral deposits on orice can cause water ow to spurt or not regulate. Mineral deposits may be removed from the
orice with a small round le not over 1/8" diameter or small diameter wire. CAUTION: DO NOT le or cut orice material.
Stream Regulator: If orice is free of material deposits, regulate ow as instructions on page 4 (Step 9). If replacement is
necessary, see parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal. To
remove tubing from the tting, relieve water pressure, push in on the gray collar while pulling on the tubing(see Fig 2, Page 1). To
insert tubing, push tube straight into tting until it reaches a positive stop, approximately 3/4".
TROUBLE SHOOTING & MAINTENANCE

PAGE 5 97878C (Rev. B - 11/04)
HRFG - ER*B HRFG - SR*B HRFG - SER*B
FIG. 7
1-1/2"(38mm)
CHILLER
INLET
21
12
CHILLER
OUTLET
20
TO BUBBLER
HRFG - ER / SR
TUBE ROUTING
FIG. 5
HRFG - SER
TUBE ROUTING
TO BUBBLER
16
CHILLER
OUTLET
CHILLER
INLET
12
FIG. 6
21
TO BUBBLER
21

PAGE 697878C (Rev. C - 02/18)
HRFG - ER*B HRFG - SR*B HRFG - SER*B
FIG. 8
SEE FIG. 5
TOP VIEW
15
9
18 1
7
11, 14, 17 21
8
3
SEE
FIG. 6
22
FIG.9
19
21
513 6
BASIN
22
4
10 REGULATOR
PART NO.
PARTS LIST
Drain
Kit - Regulator/Holder/Nuts
Strainer
Nut - Regulator Mounting
Push Button
Push Button Sleeve
Nipple Assembly
Bubbler
Gasket - Black
Screw - Cap
Screw - #10-24 Pinned Torx
Strainer
Push Button - Extension
Bottom Cover Plate-Short
Bottom Cover Plate-Extended
Back Panel HRF-SER
Back Panel HRF-ER
Back Panel HRF-SR
Kit - 1/4" Tee (3 Pack)
Insert - Threaded
Bubbler Locknut
Lower Panel HRF-SER
Lower Panel HRF-ER/SR
Kit - 1/4" Union (3 Pack)
Poly Tubing - Cut To Length
Fountain-Galaxy Gray(HRFG-S)
Fountain-Galaxy Gray(HRFG-E)
Fountain-Black(HRFG-S)
Fountain-Black(HRFG-E)
T-25 Pinned Torx Bit
LK464
98731C
45336C
45736C
45662C
45738C
15029C
51544C
100322740560
75672C
75534C
55996C
56087C
27201C
27658C
26839C
26837C
26835C
1000001994
75554C
70012C
27026C
26833C
1000002162
56092C
55969C
56053C
56025C
56056C
75520C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
NS
DESCRIPTION
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
ITEM
NO.
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
NS = NOT SHOWN