Halsey Taylor 4592FR User manual

97085C (Rev. SIE- 1/11)PAGE1
4592FR_FTN 4593FR _FTN LK4593FR_FTN
Owners Manual
Freeze Resistant Wall Mount Stone Fountains
IMPORTANT
Toassureyouinstallthismodeleasilyandcorrectly,
PLEASEREADTHESESIMPLEINSTRUCTIONSBEFORESTARTINGTHE
INSTALLATION.CHECKYOURINSTALLATIONFORCOMPLIANCEWITH
PLUMBING,ELECTRICALANDOTHERAPPLICABLECODES.Afterinstallation,leave
theseinstructionsinsidethefountainforfuturereference.
ThisFreezeResistantFountainisshippedintwoseparatecartons.Thesecondcarton
containstheFreezeResistantPackagethatisinstalledonaninteriorheatedwall.Referto
theFreezeResistantPackagefortherough-indimensionsforinstallation.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS,
ETC. TO WATER LINES ISACOMMON PROCEDURE. THIS GROUNDING MAY BE INTHE
BUILDINGOR MAYOCCURAWAYFROMTHEBUILDING.THISGROUNDING CAN CAUSE
ELECTRICALFEEDBACK INTOAFOUNTAIN, CREATINGAN ELECTROLYSIS WHICH
CAUSESA METALLIC TASTE ORAN INCREASE IN THE METALCONTENT OF THE WATER.
THISCONDITION ISAVOIDABLE BY USINGTHE PROPERMATERIALSASINDICATED.ANY
DRAIN FITTINGS PROVIDED BYTHE INSTALLER SHOULD BE MADE OF PLASTIC TO
ELECTRICALLYISOLATETHEFOUNTAINFROMTHE BUILDING PLUMBINGSYSTEM.
FIG. 1
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH PUSH IN COLLET TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 2
OPERATIONOFQUICKCONNECTFITTINGS
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
Installer
NOTE: WATER FLOW
DIRECTION
BUILDINGWATERINLET
SERVICESTOP
(NOT FURNISHED)
1/4"O.D.TUBE
WATER INLET
TOCOOLER
3/8"O.D.UNPLATED
COPPERTUBE CONNECT
COLDWATERSUPPLY

97085C (Rev. SIE - 1/11) PAGE2
4592FR_FTN 4593FR _FTN LK4593FR_FTN
4593FR ROUGH-IN
4592FR ROUGH-IN

97085C (Rev. SIE- 1/11)PAGE3
4592FR_FTN 4593FR _FTN LK4593FR_FTN
INSTALLATION INSTRUCTIONS
1. This fountain is to be mounted on a smooth, flat, finished wall surface with adequate
support structure.
NOTE: Wall mounting structure must be capable of supporting 300 lb. load on
fountain.
2. Wall should already be framed for the fountain using dimensions shown in rough-in's
on Page 2. Shown dimensions pertain to installation location.
3. Remove bottom cover from fountain and save the screws. Assemble the push rod to
the fountain. (Push rod provided with freeze resistant box)
4. Install the fountain using bolts and washers (not provided). Tighten securely.
5.Attach drain tube to fountain and cut to required length using the freeze resistant box
as a guide.
6. Install freeze resistant box - see box instructions.
7. Install a service stop (not provided) and make water supply connection from the stop to
the strainer in the freeze resistant box. DO NOT SOLDER TUBES INSERTED INTO
THE STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT.
8. Connect fountain water line to freeze resistant box - see box instructions. Replace the
bottom cover.
FIG. 3
ACORNNUT
WASHER
CLOSETSCREW
ORTHREADEDROD
(DEPENDINGONWALL TYPE
ANDANCHORUSED)
SUGGESTED CONFIGURATION FOR EXPOSED MOUNTING BOLTS

97085C (Rev. SIE - 1/11) PAGE4
4592FR_FTN 4593FR _FTN LK4593FR_FTN
100147140560
100322740560
101570540560
15013C
170705042830
400942308640
98287C
56092C
56121C
600985551640
66346C
70793C
75588C
75589C
TROUBLE SHOOTING AND MAINTENANCE
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from
the orifice with a small round file not over 1/8" diameter or small diameter wire.
CAUTION: DO NOT file or cut orifice material.
Stream Regulator: If orifice is clean, regulate flow as in “Stream Height" instructions above. If replacement is necessary,
see freeze resistant box parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal.
To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing. (See Fig.2)
To insert tubing, push tube straight into fitting until it reaches a positive stop, approximately 3/4".
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
PRINTEDINU.S.A.
ITEMIZED PARTS LIST
ITEM
NO. PART NO. DESCRIPTION
1
2
3
4
5
6-A
6-B
7
8
9
10
11
12
13
Drain Gasket
Bubbler Gasket
Drain Gasket
Bubbler Tube Assy.
Basin
Bubbler
Bubbler Assembly
Poly Tubing (Cut To Length)
Drain Elbow
Drain Plug Assy.
DrainTube
Elbow - 1/4"
Slip Joint Nut 1-1/4"
Gasket
FIG. 4
STREAM HEIGHTADJUSTMENT: Streamheight is
factory set at 35 PSI. If supply pressure varies
greatly from this, adjust screw on regulator in
freeze resistant box. Clockwise adjustment will
raise stream and counter-clockwise adjustment
will lower stream. For best adjustment, stream
should hit basin approx. 6-1/2" from bubbler. 4593FR SHOWN
10
6 -A
2
23
5
9
4
1
11
813 12
7
6 - B