Halsey Taylor HRFS-FR User manual

PAGE 1 97798C (Rev. K - 09/17)
HRFS-FR HRFE-FR
Halsey Taylor Owners Manual
HRFS-FR HRFE-FR
Freeze Resistant Fountains
Halsey Taylor Fountains are among the easiest to install Fountains on the market today. To assure you install
these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING
THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL,
AND OTHER APPLICABLE CODES. After installation, leave these instructions with the Fountain for future
reference. This Freeze Resistant Fountain is shipped in two separate cartons. The second carton(s) contains
the Freeze Resistant Package(s) HTFRB1 that are installed on an interior heated wall. The interior space must
maintain a minimium temperature of 50° F (10° C). Refer to the Freeze Resistant Package for the rough-in
dimensions for installation.
INSTALLER
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM
THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN
ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
HRFS-FR HRFE-FR

PAGE 297798C (Rev. K - 09/17)
HRFS-FR HRFE-FR
12 1/8"
308mm
7 1/4"
184mm
12"
305mm
MAX. WALL THICKNESS
34 9/16"
878mm
EDFP210FPC 28 9/16"
726mm
EDFP214FPC
34 3/4"
883mm
EDFP210FPC
28 3/4" 730mm
EDFP214FPC
3 15/16"
100mm
4"
102mm
4" 102mm
5 1/8"
130mm
5 1/8"
130mm
FINISHED FLOOR
A
B
C
D
36 1/4"
921mm
EDFP210FP
C
30 1/4"
768mm
EDFP214FP
C
1 1/2"
38mm
FIG. 1
LEGEND A = MOUNTING BOLT LOCATIONS (4) (3/8" DIA. NOT PROVIDED) B = 7/8" DIA. (22mm) HOLE FOR WATER SUPPLY TUBE C = 7/8" DIA. (22mm) HOLE FOR OPERATING CABLE D = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
HRFS - FR/HRFE - FR
MOUNTING BOLT AND ACCESS HOLE LAYOUT

PAGE 3 97798C (Rev. K - 09/17)
HRFS-FR HRFE-FR
FIG. 2
1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location. These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only). 2. Remove bottom cover from fountain and save the screws. 3. Install the fountain using bolts and washers (not provided). Tighten securely. 4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide. 5. Install freeze-resistant box - see box instructions. 6. Replace bottom cover.
HRFS - FR/HRFE - FR
ROUGH-IN DRAWINGS

PAGE 497798C (Rev. K - 09/17)
HRFS-FR HRFE-FR
FIG. 6 FIG. 7
FIG. 3 FIG. 4
See Fig. 7
See Fig. 3 FIG. 5
CABLE SHEATH ADJUSTMENT
To Increase Free Play
To Reduce Free Play

PAGE 5 97798C (Rev. K - 09/17)
HRFS-FR HRFE-FR
The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the
interior heated area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed
mounted. If recess mounted the surface of the cover must be ush with the interior wall surface. The package is
furnished with screws for mounting the cover to the box. If the box is recess mounted, do not fasten the top and bottom
of the cover to the box. Use the holes on the front only.
1. Assemble the operating cable to the fountain bracket. (Fountain should be mounted to exterior wall). The
adjustment nuts should be in the middle of threaded area on the operating cable. See Figure 3. Create a loop in
the cable and thread the free end of the cable through the wall into the freeze resistant box.
2. Connect free end of operating cable to the valve-operating bracket in the freeze resistant box.
3. Remove cable free play by adjusting the jam nuts on the ends of the operating cable. See Figure 4.
4. Connect water line from fountain bubbler into freeze resistant box. The connection to the box uses a quick connect
water tting. Position the water line, in the fountain, to drain back into interior mounted box. Any water left standing,
in the exterior line, can freeze.
To insert tubing, push tube straight into tting until it reaches a positive stop. To remove tubing from the ttings,
relieve water pressure, push in on dark gray collar while pulling out on the tubing. See Figure 9.
5. Connect drain and water supply lines to the freeze resistant fountain. Refer to Figure 1 for component positions.
Inline strainer must be used on the inlet water line. See Figure 8.
Start-up
1. Turn on building water supply and check all connections for leaks. Repair as required.
2. Stream height is factory set at 35 PSI. If stream height needs to be changed adjust the regulator in the freeze
resistant package. Clockwise adjustment raises stream height, counter clockwise adjustment will lower stream.
3. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper
valve operation. If the system is too tight the valve will stay in the on position creating constant water ow. Too
much free play will result in non-operation of the valve with the push-buttons.
4. Note: Water from the drain back tube in the freeze resistant package, will continue to run while the valve is
actuated.
5. After cable system is adjusted properly stuff exible insulation into any openings between the outside wall and the
interior box.
6. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and
fountain(s).
FIG. 8
NOTE: WATER FLOW DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
3/8" O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY
TUBE IS SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 9
OPERATION OF QUICK CONNECT FITTINGS

PAGE 697798C (Rev. K - 09/17)
HRFS-FR HRFE-FR
PART NO.
ITEM NO.
PARTS LIST
POLY TUBING (CUT TO LENGTH)
SCREW - #10 - 24 X .50 PHTC
WASTE ARM ASSY
BRACKET-REGULATOR MOUNTING
BRACKET-BASIN
BRACKET-BASIN PIVOT
HEX NUT 1-5/16
RETAINER
BUBBLER ASSEMBLY
PUSH BUTTON
SLEEVE-PUSH BUTTON GUIDE
SNAP BUSHING
BUMPER-REG. VALVE ASSY
PUSH BUTTON (EXTENSION)
PIVOT ROD
FOUNTAIN ARM - SHORT
FOUNTAIN ARM - LONG
BOTTOM COVER PLATE - SHORT
BOTTOM COVER PLATE - LONG
CAP SCREW
EDGE TRIM - 2FT.
56092C
112627543890
72000833
28823C
27945C
27946C
40045C
40206000
98118C
45662C
45663C
50198C
51667C
55919C
70425C
28782C
28783C
55000661
55000665
75672C
56369C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
DESCRIPTION
12
4
11, 18
10
14
8
15
13
5
7
6
12
16
FIG. 12
FIG. 11
FIG. 10
SEE FIG. 12
3 2, 17
SEE FIG. 11
1
19
19
For parts, contact your local distributor or call 1.800.834.4816 PRINTED IN U.S.A.
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
www.halseytaylor.com
BASIN
9