Halsey Taylor HCRF-EBP User manual

97803C (Rev. D - 5/04)
HCRFEBP*A
Halsey Taylor Owners Manual
To assure you install this model easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH
PLUMBING, ELECTRICALAND OTHER APPLICABLE CODES. After installation, leave
these instructions inside the fountain for future reference.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
FIG. 2FIG. 1
HCRF- EBP
Installer
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
Non-Refrigerated Fountain With Back Panel

97803C (Rev. D - 5/04)
HCRFEBP*A
PAGE 2
LEGEND
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED
COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM WALL SHUT
OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN
C = 1-1/4" DRAIN FURNISHED
HCRF - EBP ROUGH-IN
FIG. 3

97803C (Rev. D - 5/04)
HCRFEBP*A
PAGE 3
HCRF - EBP INSTALLATION INSTRUCTIONS
1. Wall should already be framed for the fountain using the positioning dimensions shown in Figure 3. Shown
dimensions pertain to installation location (framing must support up to 300 lbs. weight). These dimensions
are required for compliance with ANSI Standard A117.0.
2. Attach wall plate assembly to wall as shown in Figure 3 using 5/16" x 2" long bolts and flat washers
(not provided). Tighten securely. (Fastener must match wall type, i.e. lag screws for wood studs, bolts and
anchors for masonary construction.)
3. Install back panel. Place the upper edge of the panel above hanger on the wall. Slide panel down until it
engages the hanger. Be sure back panel is firmly engaged before releasing it.
4. Install rough-in plumbing as shown in Figure 3. Waste line should extend a minimum of 2" (51mm) thru the
back panel. Run supply water inlet line thru back panel. Install a service stop (not provided). Turn on supply
water and flush thoroughly.
5. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back
panel using (4) 5/16" x 3/4" long screws and washers (provided) thru holes in back panel. Tighten securely.
6. Cut waste tube to required length using plumbing hardware and a trap (not provided) as a guide. Install
hardware and trap. Tighten securely.
7. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the
fountain strainer (See Fig. 1). Turn on water supply and check for leaks. Newly installed water supply line
should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER
AS DAMAGE TO THE O-RINGS MAY RESULT.
8. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above
105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressure lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty.
9. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies
greatly from this, remove items 3 and 4 and adjust screw on regulator (Item 9). Clockwise adjustment
will raise stream height and counter-clockwise adjustment will lower stream height. For best adjustment
stream height should be approximately 1-1/2" (38mm) above the bubbler guard. (See Fig. 6)
10. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
TROUBLE SHOOTING AND MAINTENANCE
1. Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits
may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire.
CAUTION: DO NOT file or cut orifice materials.
2. Stream Regulator: If orifice is clean, regulate flow as in "START UP" instructions above. If replacement is
necessary, see parts list for correct regulator part number.
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while
pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it reaches a
positive stop, approximately 3/4".

97803C (Rev. D - 5/04)
HCRFEBP*A
PAGE 4
PARTNO.
ITEM NO.
PARTS LIST
Strainer
Retaining Nut
Push Button
Push Button Sleeve
Regulator Holder
Bubbler Assy
Gasket
Bubbler - Nipple
Regulator
Set Screw #6-32 X .31"
Screw - #10-24 X .50 PHTC
Strainer
Fountain Arm - Long
Bottom Cover Plate - Long
Back Panel
Hex Nut
Regulator Mounting Bracket
Poly Tubing (Cut To Length)
Mounting Plate Assy
Drain - Tailpipe
Drain - Adapter
Gasket - Tail Pipe
Tube - Water In
Nut-Regulator Mounting
Washer - Flat .339/.359ID Steel
Screw - Mach. 5/16-18 x 3/4
Set Screw #6-32 X .12"
Wrench-Allen
40575C
15005C
45662C
45737C
50986C
51544C
100322740560
15008C
61313C
70022C
112627543890
55996C
55001130
55000665
28290C
40045C
28291C
56092C
28286C
45679C
45805C
50074C
62095C
45736C
75541C
111577243890
70023C
75539C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
NS
DESCRIPTION
FIG. 7
FIG. 6
16 295
34
17
27
13
SEE FIG. 6
15
SEE
FIG. 5
14 1,20,21,22
12
FIG. 5
18
19
23
6
7
8
FIG. 4
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500 PRINTED IN U.S.A.
24
11
25,26
10