Halsey Taylor BFM-LR User manual

97093C (Rev. C - 10/99)
BFM-LR
PAGE 1
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
Halsey Taylor Owners Manual
Fully-Recessed Non-Refrigerated Fountain
FIG. 2FIG. 1
INSTALLER
To assure you install these models easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH
PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES. After
installation, leave these instructions with the Fountain for future reference.
BFM-LR
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER
LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY
FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING
AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
NOTE: WATER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY

97093C (Rev. C - 10/99)
BFM-LR
PAGE 2
ROUGH-IN DIMENSIONS
FIG. 3

97093C (Rev. C - 10/99)
BFM-LR
PAGE 3
1. Familiarize yourself with the wallbox which should already be placed in the wall. If not, refer to the Wall frame Installations before
proceeding.
2. Remove noise pad from paper and locate on bottom back of the basin between the drain and the bubbler holes.
CAUTION: TO INSURE PAD DOES NOT INTERFERE WITH THE HOLE AREAS, TRIM THE PAD SO THERE IS APPROX. 1/2" CLEAR-
ANCE AROUND THE HOLES.
3. Determine location of rough plumbing.
4. Attach basin mounting brackets to basin studs located in the lower corners with two (2) provided wing nuts. Tighten securely.
5. Install basin. Place the upper edge of basin above the hangers in the wall frame. Slide the basin down until it engages the hanger.
Be sure basin is firmly engaged before releasing it.
6. Finish securing basin in place through the mounting bracket using the provided two (2)#8 x 3/4" tap screws and two (2) 11/64" ID
washers. Tighten securely.
7. Install waste tube assembly. Align threaded portion of drain tube assembly with the drain hole in the basin. Place rubber gasket
between the drain assembly and the basin, then screw in the drain plug from above. Tighten the drain plug. Snap the strainer plate
into the drain plug.
8. Install a service stop (not provided) on supply inlet line.
9. Make connection from water outlet to regulator valve assembly using the provided strainer. Insert water line in inlet side of strainer
(see Figures 1 and 2) to positive stop - approximately 3/4"(19 mm). DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS
DAMAGE TO THE O-RINGS MAY RESULT.
10. Open service stop and operate push button to purge air from system. Check thoroughly for leaks. Check stream height from
bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies greatly from this, remove items 17 and 18 and adjust
screw on regulator (item 14). Clockwise adjustment will raise stream and CCW adjustment will lower stream height. For best
adjustment stream height should be approximately 1-1/2" (38 mm) above the bubbler guard. (See Figure 6).
11. Attach regulator housing (Item 13) to front panel (Item 3) with hex nut (Item 16). Install front panel. Hold panel and engage angle on
top edge of panel with lower edge of basin. Swing bottom of panel into place against the wall and secure using panel mounting
screws.
BEFORE STARTING THE INSTALLATION, PLEASE CHECK YOUR INSTALLATION
FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE
CODES
At 30" above the finished floor, cut a rectangular wall opening 17-1/8" wide by
30-1/8" high. This is required to obtain a rim height of 34-1/2" and 36" bubbler
spout height, which is in compliance with ANSI Standard A117.1 (See Fig. 4)
Reinforce wall opening on all sides so that it will adequately support the water
cooler. IT MUST SUPPORT UP TO 150 LBS. and provide a means of securing the
frame assembly in place.
Install rough-in plumbing. See Fig. 3 for location of supply water inlet and for
location of waste water outlet.
Install frame assembly in the wall opening with front edge flush with finished wall
face. Secure frame through holes in top and sides to wall support members with
5/16" diameter bolts or lag screws (not supplied). Six (6) bolts/screws are
required. CAUTION: BE SURE THAT FRAMEASSEMBLY IS SQUARED IN ITS
LOCATIONAND DO NOT USE LESS THAN REQUIRED QUANTITYAND DIAMETER
OF THE FASTENERS.
WALLFRAME INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
FIG. 4
WALL ROUGH-IN

97093C (Rev. C - 10/99)
BFM-LR
PAGE 4
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
PRINTED IN U.S.A.
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
FIG. 6
CORRECT STREAM HEIGHT
ITEMIZED PARTS LIST
ITEM NO. PART NO. DESCRIPTION
170857042830
410857042450
734253251550
23021C
23022C
62257C
100147140560
160270508650
410270508450
161637308640
411637308450
51546C
45397C
100322740560
62300C
66346C
75588C
55884C
74050011
50986C
61313C
15005C
40169C
40170C
40089C
40119C
40048C
40065C
55996C
1
2
3
4
5
6
7
8
9
10
11
11a
11b
12
13
14
15
16
17
18
19
Basin - Stainless Steel
Basin - Golden Bronzetone
Mounting Frame
Front Panel - Stainless Steel
Front Panel - Golden Bronzetone
Tube - Regulator In
Gasket
Strainer Plate - Chrome
Strainer Plate - Golden Bronzetone
Drain Plug - Chrome
Drain Plug - Golden Bronzetone
Bubbler - Chrome
Bubbler - Golden Bronzetone
Gasket - Bubbler (2-Reqd)
Tube Assy - Bubbler
Tube - Waste
Nut - Slip Joint 1-1/4
Elbow - Drain
Noise Pad
Holder Regulator
Regulator
Retaining Nut
Hex Nut - Chrome
Hex Nut - Golden Bronzetone
Cover Nut - Chrome
Cover Nut - Golden Bronzetone
Button - Chrome
Button - Golden Bronzetone
Strainer
FIG. 5
17 18 15
FRONT PANEL
14 16 13
FIG. 7
TROUBLE SHOOTING AND MAINTENANCE
CAUTION: Cleaning of Golden Bronzetone Models requires special
care. Outer surfaces must be cleaned with a mild detergent or mixture
of vinegar and water only, rinsed and wiped dry. Abrasive and acidic
cleaners may eventually damage the Golden Bronzetone finish.
Orifice Assy: Mineral deposits on orifice can cause water flow to
spurt or not regulate. Mineral deposits may be removed from the
orifice with a small round file not over 1/8" diameter or small diameter
wire. CAUTION: DO NOT file or cut orifice material.
Stream Regulator: If orifice is clean, regulate flow as in instructions.
If replacement is necessary, see parts list for correct regulator part
number.
Actuation of Quick Connect Water Fittings: Cooler is provided
with lead-free connectors which utilize an o-ring water seal. To
remove tubing from the fitting, relieve water pressure, push in on the
gray collar while pulling on the tubing.(see Fig.2) To insert tubing, push
tube straight into fitting until it reaches a positive stop, approximately 3/
4".
1
5,6,7
8,9
10
3See Fig. 5
419
11,11a,11b
12
2