Halsey Taylor HCRF-EBP User manual

Page 1 97803C (Rev. L - 02/18)
HCRFEBP*A
Halsey Taylor Owners Manual
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR
INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICALAND OTHER
APPLICABLE CODES. After installation, leave these instructions inside the fountain
for future reference.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
FIG. 2FIG. 1
HCRF- EBP
Installer
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY
Non-Refrigerated Fountain With Back Panel
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C

Page 2
97803C (Rev. L - 02/18)
HCRFEBP*A
LEGEND A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM WALL SHUT OFF BY OTHERS B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN C = 1-1/4" DRAIN FURNISHED
HCRF - EBP ROUGH-IN
FIG. 3
23 1/16"
586mm
6"
152mm
39 9/16"
1005mm
26 7/16"
672mm
25 3/16"
640mm
16"
406mm
1/2" 13mm
B
A
FINISHED FLOOR
BACK PANEL
WALL PLATE
ASSEMBLY
1/4" (6mm) DIA HOLES FOR
MOUNTING PLATE TO WALL
3/8" (10mm) DIA HOLES
FOR MOUNTING PLATE
TO WALL (10)
5 1/4"
133mm
5 1/4"
133mm
8"
203mm
8"
203mm
C
*
*
- STUDS REQUIRED
FOR FRAMED WALL CONSTRUCTION
*
19 3/4"
502mm
20 3/8"
518mm
24"
610mm CHILD ADA
REQUIREMENT
4 3/8"
111mm
12 1/8"
308mm
18"
457mm
5/8"
16mm
3 3/16"
81mm
18 3/4"
476mm

Page 3 97803C (Rev. L - 02/18)
HCRFEBP*A
HCRF - EBP INSTALLATION INSTRUCTIONS
1. Wall should already be framed for the fountain using the positioning dimensions shown in Figure 3. Shown
dimensions pertain to installation location (framing must support up to 300 lbs. weight). These dimensions
are required for compliance with ANSI Standard A117.0.
2. Attach wall plate assembly to wall as shown in Figure 3 using 5/16" x 2" long bolts and at washers
(not provided). Tighten securely. (Fastener must match wall type, i.e. lag screws for wood studs, bolts and
anchors for masonary construction.)
3. Install back panel. Place the upper edge of the panel above hanger on the wall. Slide panel down until it
engages the hanger. Be sure back panel is rmly engaged before releasing it.
4. Install rough-in plumbing as shown in Figure 3. Waste line should extend a minimum of 2" (51mm) thru the
back panel. Run supply water inlet line thru back panel. Install a service stop (not provided). Turn on supply
water and ush thoroughly.
5. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back
panel using (4) 5/16" x 3/4" long screws and washers (provided) thru holes in back panel. Tighten securely.
6. Cut waste tube to required length using plumbing hardware and a trap (not provided) as a guide. Install
hardware and trap. Tighten securely.
7. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the
fountain strainer (See Fig. 1). Turn on water supply and check for leaks. Newly installed water supply line
should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER
AS DAMAGE TO THE O-RINGS MAY RESULT.
8. These products are designed to operate on 20-105 PSI supply line pressure. If inlet pressure is above
105 PSI, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressure lower than 20 PSI or higher than 105 PSI is not
covered by warranty.
9. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies greatly
from this, adjust the screw on regulator item 2 by using a small screwdriver through the small hole in the
push button item 3 (See Fig.5). Clockwise adjustment will raise stream height and counter-clockwise
adjustment will lower stream height. For best adjustment stream height should be approximately 1-1/2" (38mm)
above the bubbler guard. (See Fig. 6)
10. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
TROUBLE SHOOTING AND MAINTENANCE
1. Orice Assy: Mineral deposits on orice can cause water ow to spurt or not regulate. Mineral deposits
may be removed from orice with a small round le not over 1/8" diameter or a small diameter wire.
CAUTION: DO NOT le or cut orice materials.
2. Stream Regulator: If orice is clean, regulate ow as in "START UP" instructions above. If replacement is
necessary, see parts list for correct regulator part number.
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the tting, relieve water pressure, push in on the gray collar while
pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the tting until it reaches a
positive stop, approximately 3/4".

Page 4
97803C (Rev. L - 02/18)
HCRFEBP*A
1-1/2"(38mm
)
PART NO.
ITEM
NO.
PARTS LIST
Kit - Drain Strainer/Ferrule
Kit - Regulator/Holder/Nut
Push Button
Push Button Sleeve
Bubbler Assy
Screw - Mach. 5/16-18 x 3/4
Washer - Flat .339/.359ID Steel
Nut-Regulator Mounting
Drain - Adapter
Cap Screw
Screw - #10-24 X .50 PHTC
Strainer
Fountain Arm - Long
Bottom Cover Plate - Long
Back Panel
Hex Nut
Regulator Mounting Bracket
Poly Tubing (Cut To Length)
Mounting Plate Assy
Drain - Tailpipe Assy.
Edge Trim - 2FT.
98924C
98530C
45662C
45737C
98533C
111577243890
75541C
45736C
45805C
75672C
112627543890
55996C
55001129
55000665
28290C
40045C
28824C
56092C
28286C
0000000930
56369C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
DESCRIPTION
FIG. 7
FIG. 6
16 2 2 2
34
17
13
SEE FIG. 6
15
SEE
FIG. 5
14 1, 9, 20
12
FIG. 5
18
19
5
FIG. 4
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500 PRINTED IN U.S.A.
8
11
6, 7
10
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
21
REGULATOR