Halsey Taylor Double Bubbler LF SCWT14CB Series User manual

PAGE 1
SCWT14ACBQ*1L
1000002180 (Rev. C - 05/16)
SCWT14CB Series Barrier-Free Water Cooler
Owners Manual

PAGE 2
SCWT14ACBQ*1L
1000002180 (Rev. C - 5/16)
FIG. 1
2, 3
4
31 - SEE FIG. 5
38
30
10
7
37
35
27
14
18
17
25
11
13
916
6
36
8
34
1, 26 - SEE FIG. 4
12
33
SEE FIG. 3
32
29
31
32
15
USES HFC-134A REFRIGERANT
Note: Danger! Electric shock hazard. Disconnect power before servicing unit.

PAGE 3
SCWT14ACBQ*1L
1000002180 (Rev. C - 05/16)
FIG. 2
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 4" (102mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 4" (102mm) (MIN.) ENTRE LES ÉVENTS DE L’ENCEINTE ET LE MUR.
F = POWER CORD 4' (1219mm) LONG
CABLE ELÉCTRICO DE 4' (1219mm) PIE, DE LARGO CORDON D’ALIMENTATION 4' (1219mm)
G = WALL SCREW HOLES
AGUJEROS DE TORNILLOS DE PARED TROUS DE VIS DU MUR
H = 2 X 4 BLOCKING
BLOQUEO DE 2 X 4 BLOC 2 X 4
FINISHED FLOOR PISO ACABADO PLANCHER FINI
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB OUT 1-1/2 IN. (38mm)
FROM WALL SHUT OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A
1-1/2" (38 mm) FUERA DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼” DE DIÁMETRO. EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE D’EAU.
C = 1-1/4 TRAP NOT FURNISHED
PURGADOR DE 1¼ NO PROPORCIONADO SIPHON 1-1/4 NON FOURNI
D = ELECTRICAL OUTLET LOCATION
UBICACIÓN DE LA TOMA DE ELECTRICIDAD EMPLACEMENT DE LA PRISE DE COURANT

PAGE 4
SCWT14ACBQ*1L
1000002180 (Rev. C - 5/16)
PUSH BUTTON VALVE ADJUSTMENT
FIG. 4
1, 26
5
20
22
21
19, 23, 24
CORRECT STREAM HEIGHT
FIG. 3
ADJUST THIS SCREW TO ELIMINATE VALVE
LEVER "FREE PLAY" OR CONTINUOUS FLOW
FROM BUBBLER
STREAM HEIGHT
ADJUSTMENT SCREW
FIG. 5
PART OF
ITEM 27

PAGE 5
SCWT14ACBQ*1L
1000002180 (Rev. C - 05/16)
Faucet Assembly Instructions
1. Place the faucet spout through the chrome cover with the smaller diameter end toward the faucet outlet.
2. Place the chrome collar over the faucet spout with the smaller diameter toward the bigger diameter chrome cover in step no. 1.
3. Place the faucet spout end down inside the same diameter hole in the brass connector.
4. Hold the chrome collar and cover up so you can get to the faucet set screw, turn the faucet spout so it goes toward the drain
on the cooler.
5. Tighten the faucet set screw gradually until faucet wil not rotate.
6. Lower the chrome collar and the chrome cover down to basin.
7. Place the chrome cover so the set screw is toward the rear of the faucet.
8. Tighten set screw until cover will not pivot.
9. Place handle on faucet with the slot toward the front of the faucet, slide the slot into the brass pin.
10. Hold handle in snug toward faucet making sure it is seated into the brass pin, and then tighten the handle set screw until
handle will not come off the brass pin.
11. Removal of the handle is exactly opposite of the assembly process.
Faucet Spout
Chrome Cover
Chrome Collar
Faucet Spout
Set Screw
Handle Set
Screw
Cover Set Screw
FIG. 6

PAGE 6
SCWT14ACBQ*1L
1000002180 (Rev. C - 5/16)
DESCRIPTION
98553C
102639931640
160270508640
28724C
55880C
98771C
98773C
36312C
98755C
45897C
66252C
601451151550
0000000247
28439C
402672043730
66203C
98846C
35887C
98531C
26860C
26861C
26862C
1000002145
61314C
55996C
1000001878
36261C
402672943730
70793C
1000001994
56278C
28719C
56092C
101452831560
1000002162
98683C
401536248410
401536242830
401536348410
401536342830
401507448410
401507442830
51454C
Kit - Bubbler/Gasket/Nipple
Drain Plug
Strainer Plate
Basin
Bracket-Regulator Mounting
Kit - Evaporator/Drier/Cold Control
Kit - Cold Control
Compressor Serv. Pak FFII2HBX
Kit - Elect (/Relay/Overload/Capacitor/Brkt.)
Drain Tube
Condenser
Push Button Assembly
Kit - 31492C Fan Motor Assy (Fan Motor, Blade, Nut)
Bracket - Hot Tank Mounting
Fan Motor Bracket
Drier
Kit - Heat Exchanger/Drier
Power Cord
Kit - Regulator/Reg. Holder/Nut
Regulator Lever
Pivot Bracket
Regulator Retaining Bracket
Kit - Regulator Holder (5-pk)
Regulator
Strainer
Kit - Bubbler Gasket (25-pk)
Hot Tank Assy
Back Panel
Elbow - 1/4 x 90°
Kit - 70682C 1/4" Tee (3-pk)
Fitting - 1/4 Snap Connect
Bracket - Clamp
Poly Tubing (Cut To Length)
Shroud - Fan
Kit - 70683C 1/4" Union (3-pk)
Kit - Drain Adaptor/Nut/Gasket/Seal
Side Panel - Right Platinum Vinyl (PV)
Side Panel - Right Stainless Steel (SS)
Side Panel - Left Platinum Vinyl (PV)
Side Panel - Left Stainless Steel (SS)
Front Panel - Platinum Vinyl (PV)
Front Panel - Stainless Steel (SS)
Snap Bushing - .75" I.D.
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
IMPRESO EN LOS E.E.U.U.
IMPRIMÉ AUX É.-U.
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE
WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or
orders for repair parts MUST include Model No. and Serial No. of cooler,
name and part number of replacement part.
ITEMIZED PARTS LIST
1
2
3
4
5
6
7
*8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
NS
NS
PART NO.
ITEM
NO.
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM