Halsey Taylor WCFS*G*L*R User manual

PAGE 1 98593C (Rev. C - 01/15)
WCFS*G*L*R WC8AFSQ*1G WC8AFSQ*2GJO
USES HFC-134A REFRIGERANT
OWNERS MANUAL
Backsplash Model Water Coolers

PAGE 298593C (Rev. C - 01/15)
WCFS*G*L*R WC8AFSQ*1G WC8AFSQ*2GJO
FIG. 1
42
41
33
28,43
29
26
25
36
24
35
27
23
22
26
31
32
24
34
21
38 39
See Fig. 3 (on Page 3)
For Push Bar Mechanism
29
37
40
30
NOTE: Non-refrigerated units do not
include all electrical and refrigeration com-
ponents shown above. Other components
and rough-in are the same as shown.

PAGE 3 98593C (Rev. C - 01/15)
WCFS*G*L*R WC8AFSQ*1G WC8AFSQ*2GJO
FIG. 2
E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6" (152mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6" (152mm) (MIN.) ENTRE LES ÉVENTS DE L’ENCEINTE ET LE MUR
F = POWER CORD 1-1/2FEET (457mm) LONG
CABLE ELÉCTRICO DE 1½ PIE, 457 mm DE LARGO CORDON D’ALIMENTATION 1-1/2' (457mm)
G = ALT. ELECTRICAL OUTLET LOCATION
UBICACIÓN ALT. DE LA TOMA DE ELECTRICIDAD EMPLACEMENT ALTERNATIF DE LA PRISE DE COURANT
H = THIS BOLT HOLE MUST BE USED FOR FASTENING UNIT TO WALL.
ESTE AGUJERO DE TUERCA DEBERÁ SER USADO PARAASEGURAR LA UNIDAD A LA PARED. ON DOIT UTILISER CE TROU DE BOULON POUR INSTALLER L’APPAREIL AU MUR.
J = ORIFICE HEIGHT 1-1/4" (32mm) ABOVE RIM
ALTURA DEL ORIFICIO 1-1/4" (32mm) SOBRE LA CORONA HAUTEUR DE L'ORIFICE 1-1/4" (32mm) AUDESSUS DU REBORD
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38mm) OUT
FROM WALL SHUT OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A
1-1/2" (38mm) FUERA DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼” DE DIÁMETRO. EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE D’EAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO** SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL OUTLET LOCATION
UBICACIÓN DE LA TOMA DE ELECTRICIDAD EMPLACEMENT DE LA PRISE DE COURANT
FINISHED FLOOR
PISO ACABADO
PLACHER FINI

PAGE 498593C (Rev. C - 01/15)
WCFS*G*L*R WC8AFSQ*1G WC8AFSQ*2GJO
HANGER BRACKETS & TRAP INSTALLATION
1) Remove hanger bracket fastened to back of cooler by
removing one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add x-
ture support carrier if wall will not provide adequate support.
IMPORTANT:
•5-1/2 in. (140mm) dimension from centerline of unit to
centerline of trap must be maintained for proper t.
Anchor hanger securely to wall using all mounting holes.
3) Install straight valve for 3/8" O.D. unplated copper tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the
hanger bracket is engaged properly in the slots on the
cooler back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at
the bottom of cooler base and two (2) screws at the top.
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install
them on the cooler waste line making sure that the end of
the waste line ts into the trap. Assemble the slip nut and
gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 35 PSI. If supply
pressure varies greatly from this, adjust screw, ac-
cessible by removing front panel (Item 7, Fig. 3). CW
adjustment will raise stream and CCW adjustment will
lower stream. For best adjustment, stream should hit
basin approximately 6-1/2” (165mm) from bubbler.
9) Replace the front panel and secure by retightening
four (4) screws.
PUSH BAR MECHANISM
LEGEND
A) Note: Water ow direction
B) Adjust this screw to eliminate mechanism “Free Play” or continuous
ow from bubbler conditions. (See ADJUSTMENT PROCEDURE)
C) Stream height adjustment (see note #8)
Water Valve Mechanism - ADJUSTMENT PROCEDURE:
- Turn adjustment screw (Item 9) “Counter-Clockwise” until water ow from bubbler starts.
- Turn adjustment screw “Clockwise” until water ow stops, THEN turn an additional 1/2 turn.
NOTE: Adjustments stated above are viewed from underneath unit (bottom side of dispenser
panel Item 1)
NOTE: If continuous ow occurs at the end of the compressor cycle, turn cold control (Item
46) counterclockwise 1/4 turn.
ITEM NO. PART NO.
Panel - Bottom Dispenser
Kit - Push Bar/Pivot Blocks/Bumpers/Rivets
Kit - Pushbars (Front & Sides)/Inserts/Nuts
Kit - Front/Side Pushbar Bracket/Screws
Panel - Right Side
Panel - Left Side
Panel - Front Push
Screw - Regulator Brkt. Mtg.
Screw - Shoulder x 1/2" Lg.
Kit - Regulator/Holder/Nut
Bracket - Regulator Mounting
Hex Nut
26588C
98537C
98895C
98789C
See Color Table
See Color Table
See Color Table
75502C
70935C
98531C
23003C
40045C
Item No. 5
Part No.
(w/o hole)
COLOR TABLE
Platinum Vinyl
Stainless Steel
Almond Vinyl
Slate Vinyl
26644C
26637C
26636C
26646C
26659C
26652C
26651C
26661C
26614C
26607C
26606C
26616C
PANEL COLOR
1
2
3
4
5
6
7
8
9
10
11
12
DESCRIPTION
26629C
26622C
26621C
26631C
26599C
26600C
26601C
26602C
Item No. 5
Part No.
(with hole)
Item No. 6
Part No.
(w/o hole)
Item No. 6
Part No.
(with hole)
Item No. 7
Part No.
FIG. 3
6
4
3
4
7
3
3
33
4
2
8
9 B
2
C
44
212 11 10 10
10 1
3
4
5
A

PAGE 5 98593C (Rev. C - 01/15)
WCFS*G*L*R WC8AFSQ*1G WC8AFSQ*2GJO
115V PARTS LIST
ITEM NO. PART NO.
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
*37
38
39
40
41
42
43
Power Cord
Fan Bracket
Kit - Fan Motor Assy/Blade/Shroud/Nut/Screws
Angle - Bracket Corner
Bracket - Front Support
Bracket - Basin Mounting
Frame - Back/Bottom
Clip (Front and Rear Panels)
Kit - Bubbler Chrome (Bubbler/Nipple/Gaskets)
Tubing - Poly (Cut to Length)
Kit - Condenser/Drier
Drier
Wrapper - Platinum Vinyl
Wrapper - Slate Vinyl
Wrapper - Almond Vinyl
Wrapper - Stainless Steel
Kit - Compr Mtg (Grommets/Cotter Pin/Washers)
Strainer
Kit - Evaporator Replacement Assembly
Compressor Serv. Pak
Kit - Electrical (Relay/Cvr/Overload)
Kit - Cold Control/Screws
Kit - Heat Exchanger/Drier
Kit - Drain (Tailpipe/Strainer/Ferrule/Gasket)
Basin - Stainless Steel
Screw - Basin Mtg.
36208C
27095C
98775C
27093C
27094C
28797C
27097C
70142C
98533C
56092C
98776C
66703C
26680C
26682C
22707C
22708C
0000000252
55996C
98724C
36322C
0000000238
98773C
98778C
98790C
26664C
75536C
DESCRIPTION
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE
WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or
orders for repair parts MUST include Model No. and Serial No. of cooler,
name and part number of replacement part.
PRINTED IN U.S.A.
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
CORRECT STREAM HEIGHT
FIG. 4
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
35827C
31430C
1000002147
98751C
35826C
Power Cord
Fan Motor
Compressor Serv. Pak
Kit - Electrical (Relay/Cvr/Overload)
Power - Inlet
21
25
*37
38
-
230V-50Hz PARTS LIST