Halsey Taylor HVRFR Series User manual

98217C (1/06)
HVR8FR*1A
Page 1
OWNERS MANUAL
HVRFR Series Barrier-Free Water Coolers
TM
1, 4
NOTE: Non-refrigerated units do not include all electrical and refrigeration
components shown above.
Other components and rough-in are the same as shown.
2, 3, 5
6
7, 22, 41
10
8
11
9, 12, 13
See Fig. 3
24 21
19
23, 30, 31, 51, 52
38, 39
42
42
16
20
25
32
21
21
21
21
43
45
45 45
45
49
50
See Fig. 4
Uses HFC-134A refrigerant
37
33
53
Fig. 1
58
59

98217C (1/06)
HVR8FR*1A
Page 2
ADA REQUIREMENT
Fig. 2
*
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION. SHUT OFF VALVE (NOT FURNISHED) TO ACCEPT 3/8” O.D. UNPLATED
COPPER TUBE.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN C = 1-1/4 TRAP NOT FURNISHED** D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL. F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER

98217C (1/06)
HVR8FR*1A
Page 3
IMPORTANT
ALL SERVICE TO BE PERFORMED BY
AN AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of cooler by removing one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier
if wall will not provide adequate support.
IMPORTANT:
y6 1/4 in. (159mm) dimension from wall to centerline of trap must be main-
tained for proper fit.
yAnchor hanger securely to wall using all five (5) 1/4 in. dia. mounting holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the hanger bracket is engaged
properly in the slots on the cooler back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at the bottom of cooler
base and two (2) screws at the top (Use torx bits sold separately). Remove the
front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler
waste line making sure that the end of the waste line fits into the trap. As-
semble the slip nut and gasket to the trap and tighten securely. Recommend
fastening cooler to wall using 7/16 bolt holes. (see fig.2, "F")
START UP
Also See General Instructions
8) Stream height is factory set at 45-50 PSI. If supply pressure varies greatly
from this, adjust screw using the access hole in the pushbutton (insert screw-
driver). CW adjustment will raise stream and CCW adjustment will lower
stream. For best adjustment, stream should hit basin approximately 6-1/2”
(165mm) from bubbler.
Stainless Steel
PANEL COLOR
COLOR TABLE Item No. 37
Part No.
Item No. 32
Part No. Item No. 33
Part No. Item No. 34 Part No. Item No. 35 Part No. Item No. 36 Part No.
28525C 28519C 28516C 28528C 28522C 22955C
Fig. 3
VANDAL RESISTANT BUBBLER DETAIL
15
1
4
Basin

98217C (1/06)
HVR8FR*1A
Page 4
51
Fig. 4
23 1
4
17,14,18
30
15
25
26
27
28
29
31
33
32
34
36
35
40
44
45 (8)
46 (2) 47 (4)
46
46
46
46
48
50
52
54
55
56
57
56
57
45 (6)

98217C (1/06)
HVR8FR*1A
Page 5
Fig. 5
Thermostat Installation Detail
Fig. 6
Heater Strip Detail
WARNING!
This unit is frost resistant down to 0° F with no wind.
Prevailing winds can reduce the ability of the heater
element to prevent light freezing. If the ambient air
temperature will drop below 0° F, the cooler needs to
be drained of all water by blowing out all water lines,
evaporator (item 20), and the drain trap. A heater strip
is used to heat the unit and will begin to cycle at 40°
+/- 5° F. A check at this temperature will ensure the
heater is working and the unit is resistant to light
freezing.
ALSO, MAKE SURE THERE ARE NO PLASTIC OR
FLAMMABLE COMPONENTS DIRECTLY ABOVE
THE HEATER STRIP. Wiring Diagram
60
21
21
61
58
59
62
45
62

98217C (1/06)
HVR8FR*1A
PRINTED IN U.S.A.
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
100322740560
100806740570
101516143550
15009C
19037000
30664C
31490C
31513C
35768C
35900C
36094C
36158C
35959C
50986C
45866C
56092C
15005C
61313C
66703C
66534C
70002C
70009C
100147140560
66723C
28462C
22897C
45662C
45737C
75672C
160270508640
600985451640
See Color Table
See Color Table
See Color Table
See Color Table
See Color Table
See Color Table
66743C
56237C
40045C
70018C
75524C
55996C
45736C
75570C
75661C
70864C
56033C
66576C
45351C
110868642550
56121C
27124C
55931C
75588C
28596C
28617C
35906C
35907C
35909C
70432C
75506C
75520C
75523C
28551C
Gasket - Bubbler
Grommet - Compressor Mtg.
Stud - Compressor Mtg.
Nipple - Bubbler
Clip - Compressor Mtg.
Fan Blade
Fan Motor
Cold Control
Cover - Relay
Power Cord
Compressor Serv. Pak EMI 70
Overload
Relay
Holder - Regulator
Bubbler
Tubing - Poly (Cut To length)
Retaining Nut
Regulator
Drier
Evaporator Assembly
Screw - #10 x 1/2” Lg. HHSM
Screw - Fan Motor
Gasket - Drain
Tube - Evap to Base
Basin - Stainless Steel
Panel - Bottom Dispenser
Button - Push
Sleeve - Push Button
Cap Screw
Strainer - Bright
Plug - Drain 1-1/2CP
Panel - RH Rear
Panel - LH Rear
Panel - RH Dispenser Side
Panel - LH Dispenser Side
Panel - Dispenser Front
Panel - Front Lower
Condenser
Shroud Fan
Hex Nut
Hex Nut - Fan Blade
Clip (Front & Rear Panels)
Strainer (See “General Instructions”)
Half Nut - Regulator
Screw - #10 x .50 Pinned Torx
Screw - #8 x .50 Pinned Torx
Screw - #8 x .62 Torx/Slot
Washer
Heat Exchanger
Wasteline
Screw - #10 - 24 x .75 Socket Head
Drain Elbow
Cover - Cold Control
Cover - Dispenser Bottom
Nut - Slip Joint 1-1/4
Panel - Screen
Screen - VR
Heater Strip
Switch - Rocker
FR Thermostat Assy.
Screw - 8-32 x .38 THTC
Screw - #10 x .75 HHSM
Torx Tool - T25
Torx Tool - T20
Hanger Bracket
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
Sold Separate
Sold Separate
NS
ITEM NO.
115V PARTS LIST
*
Page 6
DESCRIPTION
www.DrinkingFountainDoctor.com 800-518-5388