Hammer Strength Hammer Strength Linear Leg Press User manual

Hammer Strength Linear Leg Press
Owners Manual
Part Number 8344901
Rev. A-1

1. SAFETY AND WARRANTY INFORMATION
It is the sole responsibility of the purchaser of LIFE FITNESS products to read the owner’s
manual, warning labels and instruct all individuals, whether they are the end user or supervising
personnel on proper usage of the equipment.
It is recommended that all users of LIFE FITNESS exercise equipment be informed of the
following information prior to its use.
LIFE FITNESS recommends that all commercial fitness equipment be used in a supervised
area. It is recommended that the equipment be located in an access controlled area. Control is
the responsibility of the facility owner. The extent of control is at the discretion of the owner.
PROPER USAGE
1. Do not use any equipment in any way other than designed or intended by the manufacturer.
It is imperative that weight stack machines as well as any other LIFE FITNESS equipment
are used properly to avoid injury.
2. Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only
replacement parts supplied by LIFE FITNESS.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They
contain important information. If unreadable or missing, contact LIFE FITNESS for a
replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to a solid, level surface to
stabilize and eliminate rocking or tipping over. This must be performed by a licensed
contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating
equipment as well as keeping your liability to a minimum. Equipment needs to be inspected
at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any
kind is qualified to do so. LIFE FITNESS will provide service and maintenance training at
our corporate facility upon request or in the field if proper arrangements are made.
1-1

1. Safety and Warranty Hammer Strength Linear Leg Press Owners Manual
SPECIFIC OPERATING WARNINGS
1. Routinely inspect all accessory clips that join attachments to the cables and replace at the
first sign of wear.
2. Use only weight selector pins supplied by LIFE FITNESS on weight stacks. Substitutes are
forbidden.
3. Cables pose an extreme liability if used when frayed. Always replace any cable at first sign
of wear (consult LIFE FITNESS if uncertain).
4. Do not allow users to wear loose fitting clothing while using equipment. It is also
recommended to have users secure long hair back and up to avoid contact with moving
parts.
5. Fully insert weight selector pins. Partial insertion can cause weights to fall unexpectedly.
Never pin the weight stack in an elevated position. Never remove selector pin if any weights
are suspended. Never attempt to release jammed weights or parts.
6. When adjusting any seat, knee hold down pad, range of motion limiter, foothold pad or any
other type of adjuster, make certain that the adjusting pin is fully engaged in the hole to
avoid injury.
7. It is the purchaser’s sole responsibility to properly instruct its end users and supervising
personnel as to the proper operating procedures of all LIFE FITNESS equipment.
8. Keep children away from selectorized strength equipment. Parent or others supervising
children must provide close supervision of children if the equipment is used in the presence
of children.
9. Never use dumbbells or other means to incrementally increase the weight resistance. Use
only those means provided by LIFE FITNESS.
10. UNDERSTANDING EACH AND EVERY WARNING TO THE FULLEST IS IMPORTANT. IF
ANY OF THESE WARNINGS ARE UNCLEAR, ASK FOR CLARIFICATION FROM LIFE
FITNESS PERSONNEL.
11. Injuries may result if exercising improperly or excessively. It is recommended that all
individuals consult a physician prior to commencing an exercise program. If at any time
during exercise you feel faint, dizzy or experience pain, stop and consult your physician.
12. Do not exceed maximum user weight – 300 lbs.
1-2

1. Safety and Warranty Hammer Strength Linear Leg Press Owners Manual
WARRANTY
WHAT IS COVERED
This Life Fitness commercial exercise equipment (HSLLP) is warranted to be free of all defects
in material and workmanship.
WHO IS COVERED
The original purchaser or any person receiving the Product as a gift from the original purchaser.
WHO PAYS TRANSPORTATION & INSURANCE FOR SERVICE
If the Product or any covered part must be returned to a service facility for repairs, We, Life
Fitness, will pay all transportation and insurance charges for the first year. You are responsible
for transportation and insurance charges during the second and third years (if applicable).
WHAT WE WILL DO TO CORRECT COVERED DEFECTS
We will ship to you any new or rebuilt replacement part or component, or, at our option, replace
the Product. Such replacement parts are warranted for the remaining portion of the original
warranty period.
WHAT IS NOT COVERED
Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper
assembly or installation, debris resulting from any construction activities in the Product’s
environment, rust or corrosion as a result of the Product’s location, alterations or modifications
without our written authorization or by failure on your part to use, operate and maintain the
Product as set out in your Operation Manual (.Manual.). All terms of this warranty are void if
this product is moved beyond the continental borders of the United States of America
(excluding Alaska, Hawaii and Canada) and are then subject to the terms provided by
that country’s local authorized Life Fitness representative.
OPERATION MANUAL
It is VERY IMPORTANT THAT YOU READ THIS MANUAL before operating the Product.
Remember to perform the periodic maintenance requirements specified in the Manual to assure
proper operation and your continued satisfaction.
1-3

1. Safety and Warranty Hammer Strength Linear Leg Press Owners Manual
HOW TO GET PARTS & SERVICE
Simply call Customer Support Services at [phone] or [phone], Monday through
Friday from 8:00 a.m. to 6:00 p.m. Central Standard Time, and tell them your name, address
and the serial number of your Product. They will tell you how to get a replacement part, or, if
necessary, arrange for service where your Product is located or advise you on how and where
to ship the Product for service. Before shipping:
1. Obtain a Return Authorization Number (RA#) from Customer Support Services
2. Securely pack your Product (use the original shipping carton, if possible)
3. Write the RA# on the outside of the carton
4. Insure the Product, and
5. Include a letter explaining the defect or problem and a copy of your proof of purchase if you
believe the service is covered by warranty
Life Fitness World Headquarters
Attn: CSS Help Desk
5100 N. River Rd.
Schiller Park, IL. 60176
EXCLUSIVE WARRANTY
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND
EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
AND ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART. We neither assume nor
authorize any person to assure for us any other obligation or liability concerning the sale of this
Product. Under no circumstances shall we be liable under this warranty, or otherwise, of any
damage to any person or property, including any lost profits or lost savings, for any special,
indirect, secondary, incidental or consequential damages of any nature arising out of the use of
or inability to use this Product. Some states do not allow the exclusion or limitation of implied
warranties or of liability for incidental or consequential damages, so the above limitations or
exclusions may not apply to you.
CHANGES IN WARRANTY NOT AUTHORIZED
No one is authorized to change, modify or extend the terms of this limited warranty.
EFFECT OF STATE LAWS
This warranty gives you specific legal rights and you may have other rights, which vary, from
state to state.
OUR PLEDGE TO YOU
Our Products are designed and manufactured to the highest standards.
We want you completely satisfied with our Products and will do everything possible
under the terms of this warranty to keep you secure in knowing you have bought the
best!
1-4

1. Safety and Warranty Hammer Strength Linear Leg Press Owners Manual
Found at moving parts
1-5

2. GENERAL SPECIFICATIONS
1. Frame Construction
•Frame is constructed of mechanical quality steel purchased in mill run quantities
•Frame is primarily 2” x 4” and 2” x 3” rectangular tubing with 11 gauge wall
thickness. Frames are fully welded and bolt together for maximum structural integrity
and minimum maintenance when possible. However, larger machines have bolt-
together configuration to facilitate movement through smaller doorways and difficult
installations
2. Frame Finish
•Prior to applying finish, each part is chemically washed to prepare surface for
maximum adhesion
•The frames are coated with an electrostatic epoxy powder coat finish applied in a
powder form and then baked at 400°F (204°C.)
•To prevent frame and surface corrosion, wax equipment annually and keep away
from salt, chlorine and all other harmful chemicals
3. Linear Guidance System
•Two 1-1/4” precision case hardened linear shafts
•Four individual self aligning 1-1/4” linear bearings held in place with snap rings for
easy maintenence
•Custom designed heavy duty 2-1/2” bearing housing
4. Racking System
•Dual independent carriage catch and release handles simple intuitive operation
•Four position adjustable stop to accommodate a wide range of users
5. Weight Plate Holders
•Durable chrome-nickel plating on all weight plate holders
•Four built in holders accommodate Olympic plates
6. Bolts
•All hardware is stainless steel, zinc plated or nickel plated
7. Upholstery
•Contoured pads on selective units
•All edges are stitched to eliminate any folds in the material that would limit durability.
8. Foam
•Three and Four pound EVA foam (deformation resistant) or equivalent is used on all
machines. The foam is injection molded directly to the multi-ply wood support board
with integral 10mm T-nuts.

2. Specifications Hammer Strength Linear Leg Press Owner’s Manual
2-2
9. Hand Grips
•Handgrips are an extruded 60-durometer-thermorubber compound that is non-
absorbing, wear and tear resistant and exhibits good dry and wet frictional
characteristics.
•The grips are retained with aluminum collars which eliminates the tendency of the
grip to slide off the handle.
10. Seat Adjustments
•Seat and pad adjustments correctly align body to machine for proper posture,
muscle isolation and body stabilization.
•Two position quick adjust seat mechanism
11. Foot Platforms
•Thick heavy duty foot platform is rubber coated with a slip resistant texture
12. Instructional Placard
•Visual placards provide step by step instructions as well as pictures to illustrate
proper use and muscles trained.
13. Equipment Anchoring
•All machines have holes in the feet, which allow for easy anchoring to the floor. Life
Fitness recommends that all machines be anchored to the floor to minimize the
possibility that they will be tipped.
14. Warranty
•A 10-year minimum warranty on frames, 5 years on integral bearings, guide rods,
pulleys and weight plates, 1 year on cables and grips and 90 days on upholstery and
any items not specified.
•Machines are
not warranted against rust. In order to protect your machines against
rust, please repair all chips and scratches, and be sure the workout environment is
free of humidity. For example, ensure that the equipment does not share the HVAC
system with a swimming pool area. For maximum protection, please utilize an extra
coat of automotive quality finish wax and wipe excessive sweat and liquids from the
machines.
15. Liability Insurance
•Certificate of insurance available upon request

3.MACHINE SPECIFICATIONS
Product Specifications
Linear Leg Press Product # - HSLLP
Machine Weight: 630 lbs 285 kg
Load Rating: 1,800 lbs 816 kg
Max User Weight: 300 lbs 136 kg
Size: in. = 95”L x 65"W x 57”H cm =241L x 165W x 145H
Live Area: in. = 113”L x 89”W x 57”H cm =287L x 226W x 145H
•Linear bearings create a smooth feel and function throughout the life of
the product.
•Flip-in, flip-out racking mechanism is intuitive and easy to use.
•Molded pads for longer life and higher durability
•10 – 45 lb. plates maximum per weight rod
3-
1
•Start Resistance: 118 lbs. (53 kg)
Muscles Trained

4.MAINTENANCE PROCEDURES
ACTION DAILY MONTHLY BI-ANNUALLY YEARLY AS
NEEDED
CLEAN
Upholstery X
Guide Rods X
Shields X
Hand Grips X
Frames (Wax) X
INSPECT
Hardware X
Frame X
Hand Grips X
Paint
X
LUBRICATE
Guide Rods X
CLEAN
•Upholstery with a mild soap and water.
•Guide rods with a cotton cloth and break-free.
•Hand grips with mild soap and water.
•Wax frames with a standard, non-abrasive, wax finish.
INSPECT
•Hardware should be checked for looseness. Tighten as required using metric tools.
•Frames should be inspected for wear or damage.
•Handgrips should be checked for wear or damage.
•All paint chips should be filled immediately with touch-up paint.
4-1

5. Maintenance Hammer Strength Linear Leg Press Series Owners Manual
LUBRICATE
•Guide rods with Silicone Compound (part number 3238401). Apply the lubricant to a
cotton cloth, then run the cotton cloth up and down the guide rods as needed.
ONCE A DAY
• Wipe down upholstery with a mild soap and water or comparable all purpose cleaner.
• Visually inspect cables for wear at and around connections and along entire length of
cable. Always replace at first sign of wear.
ONCE A WEEK
• Visually inspect all hardware for loosening, tampering or wear.
• Check jam nut on weight stack for tightness.
• Inspect all accessory and or carabiner clips or connecting links for wear.
• Check condition of hand grips.
• Check cables for stretch and adjust as necessary by loosening the large nut on top
of the weight stack and screw in the threaded plug until cable is tight and the weight
stack pin goes in all holes easily. Tighten the large nut to complete the adjustment.
ONCE A MONTH
• Clean Guide Rods with break-free on a cloth and wipe off old residue. Clean tops of
bearings at stack and inspect for heavy buildup on rods below head plate (lift half of
stack and do a visual inspection, then clean as necessary).
• Inspect hardware on all machines and tighten any bolts or nuts that may have
loosened over the life of the product.
NOTES
• Use polishing compound (such as car wax) to clean and remove shoe scuffs from
powdercoated surfaces as necessary.
Removal of Paint, Marking Pen, Labels
Butyl cellosolve works well for removal of paints, marking pen inks, lipstick, etc.
Labels, stickers, etc. may be removed using kerosene. When the solvent will not
penetrate sticker material apply heat (hair dryer) to soften the adhesive and
promote removal. GASOLINE SHOULD NOT BE USED.
4-2