Haneco Flexion II Series User manual

The luminaire must be installed by a professional electrician.
Always switch the power o when wiring the luminaire.
Ensure input voltage conforms to the voltage range of product.
Ensure wires are securely connected.
Before switching on, ensure that all the wiring is correct.
Warranty is void if product is not installed according to the instructions.
WARNING
Product Specications
PRODUCT CODE LUMEN PER
METER lm/W CCT LEDs PER METER
CUTTING
INTERVALS
FX25W5M6K-IP20 510lm 105lm/w 6500K 60 100mm
FX25W5M6K-IP65 490lm 105lm/w 6500K 60 100mm
FX25W5M4K-IP20 530lm 105lm/w 4000K 60 100mm
FX25W5M4K-IP65 510lm 105lm/w 4000K 60 100mm
FX25W5M3K-IP20 530lm 105lm/w 3000K 60 100mm
FX25W5M3K-IP65 510lm 105lm/w 3000K 60 100mm
FX40W5M6K-IP20 980lm 100lm/w 6500K 120 50mm
FX40W5M6K-IP65 930lm 100lm/w 6500K 120 50mm
FX40W5M4K-IP20 1060lm 100lm/w 4000K 120 50mm
FX40W5M4K-IP65 970lm 100lm/w 4000K 120 50mm
FX40W5M3K-IP20 990lm 100lm/w 3000K 120 50mm
FX40W5M3K-IP65 950lm 100lm/w 3000K 120 50mm
FX75W5M6K-IP20 1220lm 90lm/w 6500K 160 31.25mm
FX75W5M6K-IP65 1180lm 90lm/w 6500K 160 31.25mm
FX75W5M4K-IP20 1330lm 90lm/w 4000K 160 31.25mm
FX75W5M4K-IP65 1250lm 90lm/w 4000K 160 31.25mm
FX75W5M3K-IP20 1240lm 90lm/w 3000K 160 31.25mm
FX75W5M3K-IP65 1200lm 90lm/w 3000K 160 31.25mm
Thanks for choosing our generation II LED Flexion light
We strongly recommend that you read this manual carefully before installation.
FLEXION II
HANECO LED FLEXION INSTALLATION GUIDE
For more information
www.haneco.com.au
1300 001 LED (533)

The luminaire must be installed by a professional electrician.
Always switch the power o when wiring the luminaire.
Ensure input voltage conforms to the voltage range of product.
Ensure wires are securely connected.
Before switching on, ensure that all the wiring is correct.
Warranty is void if product is not installed according to the instructions.
WARNING
For more information
www.haneco.com.au
1300 001 LED (533)
Installation Instructions
Cut strip to length at indicated intervals (every
167mm) using a sharp knife or scissors. Ensure
care is taken to avoid damage to terminals.
Apply sealant on end of strip. Ensure full coverage
to maintain IP65 rating.
Ensure that surface is clean and dry by using an
isopropol alcohol.
Peel o backing tape and x into position.
Connect strip to 24VDC constant voltage driver.
Fasten driver to surface with screws.
Secure strip by fastening saddles to surface.
1
3
5
2
4
6
FLEXION II
HANECO LED FLEXION INSTALLATION GUIDE