Hanna Instruments HI 9026 User manual

1
Instruction Manual
HI 9026
Calibration Check
Waterproof
pH/mV/ºC Meter
www.hannainst.com
28
SALES AND TECHNICAL SERVICE CONTACTS
Australia:
Tel. [phone]  Fax [phone]
China:
Tel. [phone]  Fax [phone]
Egypt:
Tel. & Fax [phone]
Germany:
Tel. [phone]  Fax [phone]
Greece:
Tel. [phone]  Fax [phone]
Indonesia:
Tel. [phone]  Fax [phone]
Japan:
Tel. [phone]  Fax [phone]
Korea:
Tel. [phone]  Fax [phone]
Malaysia:
Tel. [phone]  Fax [phone]
Singapore:
Tel. [phone]  Fax [phone]
South Africa:
Tel. [phone]  Fax [phone]
Taiwan:
Tel. [phone]  Fax [phone]
Thailand:
Tel. [phone]  Fax [phone]
United Kingdom:
Tel. [phone]  Fax [phone]
USA:
Tel. [phone]  Fax [phone]
For e-mail contacts and a complete list of Sales and
Technical offices, please see www.hannainst.com.
MAN9026
01/05

2
Dear Customer,
Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before using the instrument.
This manual will provide you with the necessary information for correct
use of the instrument, as well as a precise idea of its versatility.
If you need additional technical information, do not hesitate to e-mail
us at [email protected] or turn to the back cover for our
worldwide contact list.
This instrument is in compliance with directives.
WARRANTY
HI 9026 is guaranteed for two years against defects in workmanship
and materials when used for its intended purpose and maintained
according to instructions. Electrodes and probes are guaranteed for six
months. This warranty is limited to repair or replacement free of charge.
Damage due to accidents, misuse, tampering or lack of prescribed
maintenance is not covered.
If service is required, contact the dealer from whom you purchased the
instruments. If under warranty, report the model number, date of
purchase, serial number and the nature of the problem. If the repair
is not covered by the warranty, you will be notified of the charges
incurred. If the instruments are to be returned to Hanna Instru-
ments, first obtain a Returned Goods Authorization number from the
Technical Service department and then send it with shipping costs
prepaid. When shipping any instrument, make sure it is properly
packed for complete protection.
TABLE OF CONTENTS
WARRANTY .................................................................................. 2
PRELIMINARY EXAMINATION ......................................................... 3
GENERAL DESCRIPTION ................................................................. 3
FUNCTIONAL DESCRIPTION ........................................................... 4
SPECIFICATIONS........................................................................... 5
OPERATIONAL GUIDE.................................................................... 6
pH CALIBRATION ......................................................................... 9
pH BUFFER TEMPERATURE DEPENDENCE ....................................... 13
SETUP MENU ............................................................................. 14
mV CALIBRATION ....................................................................... 15
TEMPERATURE CALIBRATION ....................................................... 15
BATTERY REPLACEMENT ............................................................... 15
LCD MESSAGE GUIDE .................................................................. 16
TEMPERATURE CORRELATION FOR pH SENSITIVE GLASS ................ 17
ELECTRODE CONDITIONING & MAINTENANCE ................................ 18
TROUBLESHOOTING GUIDE ......................................................... 20
ACCESSORIES ............................................................................. 21
27
RECOMMENDATIONS FOR USERS
Before using this product, make sure that it is entirely suitable for the
environment in which it is used.
Operation of this instrument in residential areas could cause
unacceptable interferences to radio and TV equipment, requiring
the operator to follow all necessary steps to correct interferences.
The glass bulb at the end of the pH electrode is sensitive to
electrostatic discharges. Avoid touching this glass bulb at all times.
During operation, ESD wrist straps should be worn to avoid possible
damage to the electrode by electrostatic discharges.
Any variation introduced by the user to the supplied equipment may
degrade the instruments EMC performance.
To avoid electrical shock, do not use this instrument when voltages at
the measurement surface exceed 24 VAC or 60 VDC.
To avoid damage or burns, do not perform any measurement in
microwave ovens.
Hanna Instruments reserves the right to modify the design,
construction and appearance of its products without advance notice.

3
PRELIMINARY EXAMINATION
GENERAL DESCRIPTION
Remove the instrument from the packing material and examine it to
make sure that no damage has occurred during shipping.
If there is any damage, notify your dealer or the nearest Hanna
Customer Service Center.
The meter is supplied with:
 HI 1230B combination double-junction, gel pH electrode
 HI 7662 stainless steel temperature probe with 1 m (3.3') cable
 pH 4.01 & pH 7.01 buffer solutions (20 mL sachet)
 100 mL plastic beaker
 1.5V AA alkaline batteries (4 pcs)
 Instruction manual
 Rugged carrying case
Note: Save all packing material until you are sure that the instrument
functions correctly. All defective items must be returned in the
original packing with the supplied accessories.
HI 9026 is a state-of-the-art waterproof,heavy-duty pH meter designed to
provide laboratory results and accuracy under harsh industrial conditions.
This meter is provided with a series of new diagnostic features which
add an entirely new dimension to the measuremeny of pH, by
allowing the user to dramatically improve the reliability of the
measurement:
7 memorized buffers (pH 1.68, 4.01, 6.86, 7.01, 9.18, 10.01
and 12.45) for calibration
Custom calibration by entering up to two custom buffers
Messages on the LCD to make the calibration easy and accurate
Diagnostic features to alert the user when the electrode needs
cleaning
Monitoring of the electrode aging
User-selectable calibration time-out to remind when a new
calibration is necessary
HI 9026 can also measure with ORP electrodes, thanks to its capability
to measure mV with a resolution up to 0.1 mV.
Moreover, it offers an extended temperature range from 20 °C(4 °F)
to 120 °C (248 °F), using HI 7662 interchangeable probes.
26
OTHER ACCESSORIES
HI 721317 Rugged carrying case
HI 740157 Plastic electrode refilling pipet (20 pcs)
HI 76405 Electrode holder
HI 7662 Stainless steel Temperature probe with 1 m (3.3')
screened cable
HI 8427 pH and ORP electrode simulator with 1 m (3.3')
coaxial cable ending in female BNC connectors
HI 931001 pH and ORP electrode simulator with LCD and 1 m
(3.3') coaxial cable ending in female BNC connectors

4
1) BNC electrode connector.
2) Temperature probe socket.
3) Liquid Crystal Display (LCD).
4) RANGE key, to select pH or mV.
5) ON/OFF key, to turn the meter ON and OFF.
6) CAL key, to enter/exit calibration mode.
7) SETUP/CFM key, to enter setup mode or to confirm calibration.
8) UP and DOWN arrow keys, for manual temperature setting,
entering menu parameters or changing buffer values.
9) MR/CUSTOM BUF key, to recall the stored value from memory or
to enter custom buffer values.
10) MEM/CLR key, to store the reading in memory or to clear calibration.
11) LIGHT key, to toggle display backlighting.
12) Secondary display.
13) Primary display.
FUNCTIONAL DESCRIPTION
25
Kynar®is registered Trademark of Pennwalt Corp.
Ultem®is registered Trademark of General Electric Co.
HI1413B
Glass-body, single junction, flat tip, Viscolene, non-refillable, combination
pH electrode. Use: surface measurement.
ORP ELECTRODES
HI3131B
Glass-body, refillable, combination platinum ORP electrode.
Use: titration.
HI3230B
Plastic-body (Ultem®), gel-filled, combination platinum ORP electrode.
Use: general purpose.
HI4430B
Plastic-body (Ultem®), gel-filled, combination gold ORP electrode.
Use: general purpose.
Consult the Hanna General Catalog for a complete and wide selection
of electrodes.
110 mm
4.3"
12 mm
0.5"
HI 1413
150 mm
5.9"
12 mm
0.5"
HI 3111
"S" VERSION
HI 3131
120 mm
4.7"
12 mm
0.5"
HI 3230
HI 3210
"S" VERSION
120 mm
4.7"
12 mm
0.5"
HI 4430
HI 4410
"S" VERSION

5
SPECIFICATIONS
EGNAR
Hp00.61ot00.2
Vm9991±/Vm9.996±
)F°0.842ot0.4(C°0.021ot0.02
NOITULOSER
Hp10.0
Vm1/Vm1.0
)F°1.0(C°1.0
YCARUCCA
Fº86/Cº02@
Hp10.0±
Vm1±/Vm2.0±
)F°8.0±(C°4.0±
)rorreeborpgnidulcxe(
noitaiveDCMElacipyT
Hp20.0±
Vm1±/Vm2.0±
)F°8.0±(C°4.0±
noitarbilaCHp
,erudecorptniop-2ro1
2dnasreffubdeziromem7htiw
sreffubmotsuc
noitarbilaCtesffO Hp1±
noitarbilaCepolS %801ot08morF
noitasnepmoCerutarepmeT
C°0.021ot0.02morf,citamotuA
,launamro)F°0.842ot0.4(
eborperutarepmettuohtiw
edortcelEHp )dedulcni(B0321IH
eborPerutarepmeT )dedulcni(2667IH
ecnadepmItupnI 01
21
smho
efiL&epyTyrettaB )seirettabenilakla(ezisAAV5.1x4
esusuounitnocfosruoh005.xorppa
ffo-otuA rosetunim02:elbatcelesresU
delbasid
snoisnemiD )4.2x1.3x7.7(mm06x08x691
)ylnoretem(thgieW ).zo51(g524
tnemnorivnE )F°22123(C°050
%001HRxam
ytnarraW sraey2
24
120 mm
4.7"
12 mm
0.5"
FC 100
75 mm
2.95"
6 mm
0.25"
FC 200
120 mm
4.7"
12 mm
0.5"
FC 210
120 mm
4.7"
12 mm
0.5"
9.5mm DIA
0.37"
FC 220
110 mm
4.3"
12 mm
0.5"
FC 911
FC100B
Plastic-body (Kynar®), double junction, refillable, combination pH
electrode.
Use: general purpose for food industry.
FC200B
Plastic-body (Kynar®), open junction, conic, Viscolene, non-refillable,
combination pH electrode. Use: meat & cheese.
FC210B
Glass-body, double junction, conic, Viscolene, non-refillable, combination
pH electrode.
Use: milk, yogurt.
FC220B
Glass-body, triple-ceramic, single junction, refillable, combination pH
electrode. Use: food processing.
FC911B
Plastic-body (Kynar®), double junction, refillable with built-in amplifier,
combination pH electrode. Use: very high humidity.

6
INITIAL PREPARATION
The meter is supplied complete with batteries. Remove the back cover,
unwrap the batteries and install them while paying attention to their
polarity (see page 15).
To prepare the instrument for use, connect the pH electrode and the
temperature probe to the BNC and temperature sockets on the top of
the instrument. The temperature probe is used in conjunction with
the pH electrode to utilize the meter's ATC capability, but it can also
be used independently to take temperature measurements. If the
probe is disconnected, temperature can be set manually with the UP
and DOWN arrow keys (see page 7 for details).
Turn the instrument ON by pressing ON/OFF.
At start-up the display will show all the used segments for a few seconds
(or while the button is held), followed by the percentage indication of the
remaining battery charge, then enters measurement mode.
After measurement switch the meter off, clean the electrode and store it
with a few drops of HI 70300 storage solution in the protection cap.
The auto-off feature turns the meter off after 20 minutes with no
button pressed to save battery life. To disable this feature, see Setup
Menu section on page 9.
pH MEASUREMENTS
To take a pH measurement remove the elec-
trode protective cap and simply submerge
the tip (4cm/1½") of the electrode and the
temperature probe into the sample to be tested.
If necessary, press the RANGE key until the
display changes to the pH mode.
Allow for the electrode to adjust and reading
to stabilize (hourglass symbol turns off).
The LCD will show the pH measurement
together with the temperature of the sample.
OPERATIONAL GUIDE
23
HI1330B
Glass-body, semimicro, single junction, refillable, combination pH electrode.
Use: laboratory, vials.
HI1331B
Glass-body, semimicro, single junction, refillable, combination pH electrode.
Use: flasks.
HI1230B
Plastic-body (Ultem®), double junction, gel-filled, combination pH
electrode.
Use: general, field.
HI2031B
Glass-body, semimicro, conic, refillable, combination pH electrode.
Use: semisolid products.
HI1332B
Plastic-body (Ultem®), double junction, refillable, combination pH
electrode.
Use: general purpose.
120 mm
4.7"
5mm
0.2"
5mm DIA
0.2"
HI 1310
"S" VERSION
HI 1330
120 mm
4.7"
12 mm
0.5"
HI 1210
"S" VERSION
HI 1230
75 mm
2.95"
6 mm
0.25"
HI 2020
"S" VERSION
HI 2031
120 mm
4.7"
12 mm
0.5"
HI 1312
"S" VERSION
HI 1332
210 mm
8.25"
8 mm
0.3"
7.5mm DIA
0.29"
HI 1311
"S" VERSION
HI 1331

7
In order to take more accurate pH measurements, make sure that the
instrument is calibrated (see page 9 for details).
It is recommended that the electrode is always kept wet and rinsed
thoroughly with the sample to be measured before use.
The pH reading is directly affected by temperature. In order for the
meter to measure the pH accurately, temperature must be taken into
consideration. If the sample temperature is different from the tempera-
ture at which the pH electrode was kept, allow a few minutes to reach
thermal equilibrium.
To use the meter's Automatic Temperature Compensation feature,
submerge the temperature probe into the sample as close to the
electrode as possible and wait for a few minutes.
If manual temperature compensation (MTC) is desired, the
temperature probe must be disconnected from the instrument.
The display will show the default temperature
of 25 °C or the last temperature set with the
"°C" (or "°F") indicator blinking.
The MTC tag and up & down arrows symbols light up on the LCD to
indicate that the meter is in MTC mode and the arrow keys can be
used to enter the desired temperature value.
Note:When in MTC the user can press and hold the arrow keys, and
the meter will start incrementing/decrementing the temperature
value. The meter keeps measuring and the display is updated
every second.
ORP MEASUREMENTS
To perform ORP measurements, connect an optional ORP electrode
(see "Accessories" section) to the meter and turn it ON.
If necessary, enter the "mV" mode by pressing RANGE until the
display changes to mV.
Submerge the ORP electrode tip (4cm/1½") into the sample to be
tested and wait a few minutes for the reading to stabilize.
Measurements within the ±699.9 mV range are displayed with 0.1
mV resolution, while outside this range the resolution automatically
switches to 1 mV.
The ATC (or MTC) tag is turned off because mV readings are not
temperature compensated.
22
pH ELECTRODES
All electrodes part numbers ending in B are supplied with a BNC
connector and 1 m (3.3') cable, as shown below:
HI1043B
Glass-body, double junction, refillable, combination pH electrode.
Use: strong acid/alkali.
HI1053B
Glass-body, triple ceramic, conic shape, refillable, combination pH electrode.
Use: emulsions.
HI1083B
Glass-body, micro, Viscolene, non-refillable, combination pH electrode.
Use: biotechnology, micro titration.
HI1131B
Glass-body, single junction, refillable, combination pH electrode.
Use: general purpose.
120 mm
4.7"
12 mm
0.5"
9.5mm DIA
0.37"
HI 1040
"S" VERSION
HI 1043
120 mm
4.7"
12 mm
0.5"
HI 1050
"S" VERSION
HI 1053
120 mm
4.7"
12 mm
0.5" 5 mm
0.2"
3 mm
0.12" 3.0 mm DIA
0.12"
HI 1083
120 mm
4.7"
12 mm
0.5"
9.5mm DIA
0.37"
HI 1111
"S" VERSION
HI 1131
ORP SOLUTIONS
HI7020L Test Solution 200-275 mV, 500 mL bottle
HI7020M Test Solution 200-275 mV, 230 mL bottle
HI7021L Test Solution 240 mV, 500 mL bottle
HI7021M Test Solution 240 mV, 230 mL bottle

8
For accurate ORP measurements, the surface of the electrode must be
clean and smooth. Pretreatment solutions are available to condition
the electrode and improve its response time (see "Accessories" section).
Notes:
When the reading is out of range, the display will flash the closest
full-scale value.
If using pH electrode while in mV mode, the meter will measure
the mV generated by the pH electrode.
MEM & MR FUNCTIONS
From normal measurement mode, pressing the MEM key will freeze
the readings on the display and store into internal memory the
current values (pH and temperature, or mV and temperature)
together with condition and buffer segments.
The MEM tag blinks and the display remains frozen until the MEM
key is pressed again.
Note: While in MEM mode, the user can switch between pH and mV
by pressing the RANGE key.
A stored value can be recalled by pressing MR: the display will show
the value, together with the RCL & MEM tags, as long as the MR key
is pressed.
Note: Pressing MR, only the range that was active at the time MEM
was pressed is shown.
BACKLIGHT FEATURE
The meter is provided with a Backlight feature,
which can be easily toggled on and off through
the keyboard by pressing the LIGHT key.
Note: The backlight automatically shuts off after approximately 1 minute
with no buttons pressed.
21
ACCESSORIES
pH CALIBRATION SOLUTIONS
HI70004P pH 4.01 Buffer Solution, 20 mL sachet, 25 pcs
HI70006P pH 6.86 Buffer Solution, 20 mL sachet, 25 pcs
HI70007P pH 7.01 Buffer Solution, 20 mL sachet, 25 pcs
HI70009P pH 9.18 Buffer Solution, 20 mL sachet, 25 pcs
HI70010P pH 10.01 Buffer Solution, 20 mL sachet, 25 pcs
HI 7001L pH 1.68 Buffer Solution, 500 mL bottle
HI 7001M pH 1.68 Buffer Solution, 230 mL bottle
HI7004L pH 4.01 Buffer Solution, 500 mL bottle
HI7004M pH 4.01 Buffer Solution, 230 mL bottle
HI7006L pH 6.86 Buffer Solution, 500 mL bottle
HI7006M pH 6.86 Buffer Solution, 230 mL bottle
HI7007M pH 7.01 Buffer Solution, 500 mL bottle
HI7007M pH 7.01 Buffer Solution, 230 mL bottle
HI7009L pH 9.18 Buffer Solution, 500 mL bottle
HI7009M pH 9.18 Buffer Solution, 230 mL bottle
HI7010L pH 10.01 Buffer Solution, 500 mL bottle
HI7010M pH 10.01 Buffer Solution, 230 mL bottle
ELECTRODE STORAGE SOLUTION
HI70300L Storage Solution, 460 mL bottle
HI70300M Storage Solution, 230 mL bottle
ELECTRODE CLEANING SOLUTIONS
HI70000P Electrode Rinse Solution, 20 mL sachet, 25 pcs
HI7061L General Cleaning Solution, 460 mL bottle
HI7061M General Cleaning Solution, 230 mL bottle
HI7073L Protein Cleaning Solution, 460 mL bottle
HI7073M Protein Cleaning Solution, 230 mL bottle
HI7074L Inorganic Cleaning Solution, 460 mL bottle
HI7074M Inorganic Cleaning Solution, 230 mL bottle
HI7077L Oil & Fat Cleaning Solution, 460 mL bottle
HI7077M Oil & Fat Cleaning Solution, 230 mL bottle
REFILLING ELECTROLYTE SOLUTIONS (50 mL, 4 pcs)
HI7071 3.5M KCl+AgCl Electrolyte for single junction electrodes
HI7072 1M KNO3Electrolyte
HI7082 3.5M KCl Electrolyte for double junction electrodes
HI8093 1M KCl+AgCl Electrolyte
ORP PRETREATMENT SOLUTIONS
HI7091L Reducing Pretreatment Solution, 460 mL bottle
HI7091M Reducing Pretreatment Solution, 230 mL bottle
HI7092L Oxidizing Pretreatment Solution, 460 mL bottle
HI7092M Oxidizing Pretreatment Solution, 230 mL bottle

9
pH CALIBRATION
It is recommended to calibrate the instrument frequently, especially if
high accuracy is required.
The pH range should be recalibrated:
a) Whenever the pH electrode is replaced.
b) At least once a week.
c) After testing aggressive chemicals.
d) When extreme accuracy is required.
e) When the calibration time-out is expired (if feature is enabled).
PROCEDURE
The meter offers a choice of 7 memorized buffers (1.68, 4.01, 6.86,
7.01, 9.18, 10.01 and 12.45 pH) and also allows the user to enter
two more pH values for calibration, C1 and C2 (see Custom Buffer
Selection section on page 12 for details).
Pour small quantities of selected buffer solutions into clean beakers.
For accurate calibration use two beakers for each buffer solution, the
first one for rinsing the electrode and the second one for calibration.
Remove the protective cap and rinse the electrode with some of
the buffer solution to be used for the first calibration point.
TWO-POINT CALIBRATION
Press the CAL key. The "CAL" and " " indicators will be
displayed. The secondary LCD will display buffer "7.01". If a
different calibration buffer is desired (e.g. 6.86), use the UP
and DOWN arrow keys to change the displayed value.
Submerge the electrode approximately 4 cm (1½") into the
solution, place the temperature probe as close as possible to the
electrode and stir gently.
The LCD will flash "NOT READY" for 12
seconds, then:
if the reading is not close to the selected
buffer, "WRONG " and "WRONG "
will blink alternatively;
if it is close to the selected buffer the
meter will advise the user with an
acoustic signal (if enabled) when the
reading becomes stable and the display
will change to "READY" and blinking "CFM".
or
20
TROUBLESHOOTING GUIDE
SMOTPMYS MELBORP NOITULOS
evissecxe/esnoperwolS
.tfird
.edortceleHpytriD IHnipitedortceleehtkaoS
03rofnoitulos1607
wollofnehtdnasetunim
.erudecorPgninaelCeht
pusetautculfgnidaeR
.)esion(nwoddna
.noitcnujytrid/deggolC
leveletylortcelewoL
sedortceleelballifer(
.)ylno
.edortceleehtnaelC
etylortcelehserfhtiwllifeR
.)ylnosedortceleelballifer(
swohsyalpsiD
elacsllufgniknilb
.eulav
fotuognidaeR
.egnar
sielpmastahtkcehC
;egnarelbarusaemnihtiw
dnaleveletylortcelekcehC
.sutatsedortcelelareneg
fotuoelacsVm
.egnar
yrdroenarbmemyrD
.noitcnuj
00307IHniedortcelekaoS
tsaeltarofnoitulosegarots
.setunim03
swohsyalpsiD
.F°roC°gniknilb
redrofotuO
.eborperutarepmet
erutarepmetecalpeR
.eborp
swohsyalpsiD
.gniknilbNAELC
neewtebecnereffiD
suoiverpdnawen
neebsahnoitarbilac
.detceted
dnaedortcelenaelC
melborpehtfI.etarbilacer
reffubehtkcehc,sniamer
.snoitulos
swohsyalpsiD
yrettabgniknilb
.lobmys
.levelyrettabwoL .seirettabegnahC
krowtonseodreteM
erutarepmethtiw
.eborp
erutarepmetnekorB
.eborp
erutarepmetecalpeR
.eborp
etarbilacotsliafreteM
ytluafsevigro
.sgnidaer
.edortceleHpnekorB .edortceleecalpeR
siLACGNORW
Hpgniruddeyalpsid
.erudecorpnoitarbilac
rognorW
.reffubdetanimatnoc
noitulosreffubtahtkcehC
.hserfdnatcerrocsi
.ffostuhsreteM ;seirettabdaeD
sierutaefffo-otuA
,esacsihtni:delbane
retfaffostuhsretem
.esu-nonfonim02
;seirettabegnahC
.FFO/NOsserP
2rE,1rE,0rE
.putratstaegassem
.rorreMORPEE ynarorelaedruoytcatnoC
.retneCecivreSannaH
tratstaegassemrlC
.pu
HptluafeddedaoL
.seulavnoitarbilac
.noitarbilacHpmrofreP

10
Press the CFM key to confirm the calibra-
tion: the meter stores the first calibration
point; the primary LCD will show the
calibrated reading, while the secondary
LCD will show the second buffer to be
used for calibration (pH 4.01).
If youre going to calibrate with a
different buffer, select the desired value
by pressing the arrow keys.
Submerge the electrode approximately 4 cm (1½") into the
second buffer solution, place the temperature probe as close as
possible to the electrode and stir gently.
The LCD will flash "NOT READY" for 12 seconds, then:
if the reading is not close to the selected buffer, "WRONG "
and "WRONG " will blink alternatively;
if it is close to the selected buffer the meter
will advise the user with an acoustic
signal (if enabled) when the reading
becomes stable and the display will change
to "READY" and blinking "CFM".
Press the CFM key: the value is stored in memory and the meter
returns to normal mode. The tags corresponding to the buffers
used for calibration will light up together with the condition
bargraph (if enabled).
Note: The meter automatically skips the buffer used for the first calibration
point to avoid erroneous procedure. A difference of at least 1.5 pH
unit is required between the two buffers used for the offset and slope
calibration: once calibrated at either pH 7.01 or 6.86, the
instrument automatically ignores the other value for the second point
(same for pH 10.01 and 9.18).
Note: During calibration, the secondary LCD shows the selected buffer
value; press RANGE to display the buffer temperature.
Note: To clear a previous calibration and return to the default
values, press CLR at any time after entering the calibration
mode. The LCD will show CLr CAL for one second, and then
will return to normal measurement mode.
The LCD will show an empty bargraph to warn the user that
the meter is not calibrated.
19
For refillable electrodes, if the refill solution (electrolyte) is more than 2½
cm (1") below the fill hole, add the appropriate Electrolyte Solution.
MEASUREMENT
Rinse the electrode tip with distilled water, immerse it (4 cm / 1½")
in the sample and stir gently for a few seconds.
For a faster response and to avoid cross contamination of the samples,
rinse the electrode tip with the solution to be tested, before taking
any measurements.
STORAGE PROCEDURE
To minimize clogging and ensure a quick response time, the glass
bulb and the junction should always be kept moist.
When not in use, store it with a few drops of HI 70300 storage
solution in the protective cap.
NEVER STORE THE ELECTRODE IN DISTILLED OR DEIONIZED
WATER.
PERIODIC MAINTENANCE
Inspect electrode and cable. The cable used for the connection to the
meter must be intact and there must be no points of broken
insulation on the cable or cracks on the electrode stem or bulb. If any
scratches or cracks are present, replace the electrode. Rinse off any salt
deposits with water.
Connectors must be perfectly clean and dry.
For refillable electrodes:
Refill the electrode with fresh electrolyte (see the electrodes specifications
to select the correct refilling solution). Allow the electrode to stand
upright for 1 hour. Follow the Storage Procedure above.
CLEANING PROCEDURE
 General Soak in Hanna HI 7061 General Cleaning
Solution for approximately ½ hour.
 Protein Soak in Hanna HI 7073 Protein Cleaning
Solution for 15 min.
 Inorganic Soak in Hanna HI 7074 Inorganic
CleaningSolution for 15 min.
 Oil/grease Rinse with Hanna HI 7077 Oil & Fat Cleaning
Solution for 1 min.
IMPORTANT: After performing any of the cleaning procedures, rinse
the electrode thoroughly with distilled water and soak it in HI 70300
Storage Solution for at least 1 hour before taking measurements.