Hans Grohe Croma 160 Showerpipe27245000 Manual

Croma 160 Showerpipe
27245000
ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 4

安全技巧
装配时为避免挤压和切割受伤，必须戴上手
套。
头顶花洒夹持杆只为夹持头顶花洒而设计，不
得让其承载其它物品！
不得让儿童和肢体、精神和/或意识有障碍的成
人在不受监管的情况下使用淋浴系统。受酒精
或毒品影响的人员不得使用淋浴系统。
必须避免让身体敏感部位（如眼睛）接触到莲
蓬头喷水。必须保持莲蓬头与人头之间有足够
的距离。
该产品不得作扶柄使用。必须安装单独的扶
柄。
本产品只允许作为洗浴、卫生和洁身之用。
冷热水管间过大的压力差必须予以平衡。
安装提示
• 安装前必须检查产品是否受到运输损害。安装
后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗
和检查。
• 请遵守当地国家现行的安装规定。
• 本安装说明中所规定的安装尺寸理想用于身高
1700mm左右的人士。尺寸可根据需要进行修
改。在这种情况下，您必须留意，如果安装高度
改变，则花洒到地板的最小高度也随之改变，且
必须考虑到连接尺寸的改变。
• 由有资格的专业人员进行产品安装时请注意：在
所有加固区域中，加固表面是否平整（无突出的
接缝或瓷砖），墙体结构是否适合产品安装且未
显露出任何缺点。
• 必须装上花洒所附带的滤网密封垫，以过滤管道
里的杂质污物。杂质污物会影响花洒的功能和/
或损坏花洒的功能部件，由此而产生的产品损坏
不属于汉斯格雅的保修范围。
• 紧急情况下,可使用细的锯子将下方区域中阀门
与头顶莲蓬头之间的管子锯短。
中文
技术参数
工作压强： 最大1MPa
推荐工作压强 0,15-0,5MPa
测试压强： 1,6MPa
(1MPa=10bar=147PSI)
热水温度： 最大70°C
推荐热水温度： 65°C
中心距离： 150±12mm
连接管线G1/2： 左热右冷
热力消毒: 最大70°C/4分钟
• 自动防止回流
• 该产品专为饮用水设计！
2

备用零件
(参见第页18)
大小
(参见第页11 )
流量示意图
(参见第页11 )
手持花洒
顶置花洒
操作(参见第页12)
请在使用喷头后略微倾斜，排空其中
水分。
清洗
(参见第页14)
安装参见第页6
选装附件
(不在供货范围内)
匹配瓷砖的圆盘镀铬#95163000
(参见第页18)
问题 原因 补救
龙头出水量小 -花洒滤网有垃圾堵塞 -清洗花洒和软管间的过滤网
龙头不灵活 -阀芯损坏，结垢 -更换阀芯
龙头滴水 -阀芯损坏 -更换阀芯
热水温度过低 -温度限制器设置错误 -设置温度限制器
燃气热水器不工作 -花洒滤网有垃圾堵塞 -清洗花洒和软管间的过滤网
中文
符号说明
调节(参见第页10)
热水温度调节。如果使用即热式喷头，
则不建议安装热水阀门。
请勿使用含有乙酸的硅胶！
3

Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The arm of the shower head is intended only to hold
the shower head. Do not load it down with other
objects!
Children as well as adults with physical, mental and/
or sensoric impairments must not use this product
without proper supervision. Persons under the influ-
ence of alcohol or drugs are prohibited from using
this product.
Do not allow the streams of the shower touch sensi-
tive body parts (such as your eyes). An adequate
distance must be kept between the shower and you.
The product may not be used as a holding handle. A
separate handle must be installed.
The product may only be used for bathing, hygienic
and body cleaning purposes.
The hot and cold supplies must be of equal pres-
sures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
• The installation dimensions stated in these installation
instructions are ideal for people of approximately
1700 mm in body height. The dimensions can be al-
tered if required. In this case, pay attention to the fact
that a change of installation height will also change
the minimum height, and that the altered mounting
dimensions must be taken into consideration.
• During installation of the product by qualified trained
personnel, make sure that the entire fastening surface
is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply the
product and has no weak points.
English
• The mesh washer must be insert to protect the over-
head shower against incoming dirt by pipework. In-
coming dirt leads to defects or/and can damage parts
of the shower; such caused faults voids all liability and
guarantee claims.
• If required, the bottom part of the pipe between the
fixture and the shower head can be shortened with a
fine-toothed saw.
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure 0,15 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Centre distance: 150 ± 12 mm
Connections G 1/2: cold right - hot left
Thermal disinfection: max. 70°C / 4 min
• Safety against backflow
• The product is exclusively designed for drinking water!
4

Spare parts
(see page 18)
Dimensions
(see page 11 )
Flow diagram
(see page 11 )
 Hand shower
 overhead shower
Operation(see page 12)
To empty the overhead shower after use,
hold it in a slightly inclined position.
Cleaning
(see page 14)
Assembly see page 6
Special accessories
(order as an extra)
tile-matching-disk chrome plated
#95163000 (see page 18)
Fault Cause Remedy
Insufficient water -Shower filter seal dirty -Clean filter seal between shower
and hose
Mixer stiff -Cartridge defective, calcified -Exchange cartridge
Mixer dripping -Cartridge defective -Exchange cartridge
Hot water temperature too low -Hot water limiter incorrectly set -Set hot water limiter
Instantaneous heater didn’t work -Shower filter seal dirty -Clean filter seal between shower
and hose
English
Symbol description
Adjustment (see page 10)
To adjust the hot water limiter. Using a hot
water limiter in combination with a continu-
ous flow water heater is not recommended.
Do not use silicone containing acetic acid!
5

6
Montage
1 2
2.
1.
2.
1.
36 mm
3a
3b
95163000
max.
39 mm
max.
5 mm

7
Montage
4 5
67
SW 8 mm
1.
2.
SW 8 mm
8

8
Montage
1.
Ø 6 mm
2.
9
Silicone
10
3.
12
11
1.
2.
3.
max. 875 mm

9
2.
Nr. 10476220
Armaturenfett
Grease
1.
13
95659000
94246000
SW 17 mm
14
10 Nm
15 16
94246000

60 °C 10 °C 0,3 MPa
+
21 3
45
6 7
4.
3.
1.
2.
3.
1.
2.
6 x
36°C
38°C
43°C
50°C
55°C
60°C
17 x
4 mm
4 mm
5 Nm
4 mm
4 mm
10
Justierung