Hans Grohe Ecostat E 15707007 User manual

ZH 用户手册/组装说明 2
EN Instructions for use / Assembly instructions 4
Lesezeichen
中文 2
English 4
Ecostat E
15707007
°C
40
Ecostat Square
15712007

2
中文
安全技巧
装配时为避免挤压和切割受伤,必须戴上手套.
本产品只允许作为洗浴,卫生和洁身之用.
不得让儿童和肢体,精神和/或意识有障碍的成
人在不受监管的情况下使用淋浴系统.受酒精
或毒品影响的人员不得使用淋浴系统.
冷热水管间过大的压力差必须予以平衡.
安装提示
• 安装前必须检查产品是否受到运输损害.安装
后将不认可运输损害或表面损伤.
• 管道和阀门必须根据通用标准进行安装,冲洗
和检查.
• 请遵守当地国家现行的安装规定.
技术参数
工作压强: 最大1MPa
推荐工作压强:0,1-0,5MPa
测试压强:1,6MPa
(1MPa=10bar=147PSI)
热水温度: 最大60°C
热力消毒:70°C/4分钟
• 自动防止回流
• 该产品专为饮用水设计!
符号说明
请勿使用含有乙酸的硅胶!
安全功能 (参见第页10)
恒温阀芯的安全功能可以预先设定所希望的最高
出水温度,例如最高温度为42°C
调节 (参见第页10)
安装完成后必须检查调温器的出水温度.如在取水
处测量所得的温度与调温器上设定的温度有偏差,
那么必须进行调整.
保养 (参见第页12)
• 单向阀必须在符合国家或当地的法律的情况下
按照EN806-5定期检查(至少一年一次).
• 为了保证恒温器的稳定运转,请务必定期从最
热到最冷转动调温器.
大小 (参见第页15)
流量示意图 (参见第页15)
 时的流速
备用零件 (参见第页16)
选装附件 (参见第页17)
 不在供货范围内
• 加长25mm#13595000
• 加长件22mm(墙壁不够深
时)#13593000
• 加长件22mm(墙壁不够深时)
#15597000
• 调平装置1°#95521000
清洗 (参见第页18)
操作 (参见第页9)
+

3
中文
安装 (参见第页6)
问题 原因 补救
龙头出水量小 - 水压不足 - 检查总水压
- 调压器过滤网脏污 - 清洁龙头前面和恒温阀芯的过滤
网.
- 花洒滤网有垃圾堵塞
- 花洒过滤器元件有垃圾堵塞
- 清洗花洒和软管间的过滤网
- 清洗花洒和软管间的过滤密封件
串水,在龙头关闭的状态下,热水
被强迫流入冷水管路,或者相反.
- 单向阀有垃圾堵塞或漏水 - 清洗单向阀,如有必要则更换新
的
龙头出水温度和温度设定的不符 - 恒温阀芯未被调节 - 调节恒温器
- 热水温度过低 - 将热水温度从42ºC升高到60ºC
水温无法调节 - 恒温阀芯表面结垢 - 更换-恒温阀芯
- 对于新的安装:基体连接不正确
(可能是:右冷,左热)或者安装时
旋转180º
- 安装功能块时,旋转180º
安全停止按钮不工作 - 弹簧损坏
- 按钮僵化
- 清洁弹簧和/或按钮,并视需要更
换
阀门不灵活 - 关闭部件损坏 - 更换关闭部件
花洒或龙头出水嘴滴水 - 在阀体上有灰尘或水垢,阀芯损
坏
- 清洗或更换闭锁阀芯

4
English
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The product may only be used for bathing, hygienic
and body cleaning purposes.
Children as well as adults with physical, mental and/
or sensoric impairments must not use this product
without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from
using this product.
The hot and cold supplies must be of equal
pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Thermal disinfection: 70°C / 4 min
• Safety against backflow
• The product is exclusively designed for drinking
water!
Symbol description
Do not use silicone containing acetic acid!
Safety Function (see page 10)
The desired maximum temperature for example max.
42º C can be pre-set thanks to the safety function.
Adjustment (see page 10)
After the installation, the output temperature of the
thermostat must be checked. A correction is necessary if
the temperature measured at the output differs from the
temperature set on the thermostat.
Maintenance (see page 12)
• The check valves must be checked regularly
according to EN 806-5 in accordance with national
or regional regulations (at least once a year).
• To guarantee the smooth running of the thermostat, it
is necessary from time to time to turn the thermostat
from total hot to total cold.
Dimensions (see page 15)
Flow diagram (see page 15)
free flow
Spare parts (see page 16)
Special accessories (see page 17)
order as an extra
• extension 25 mm #13595000
• Extension Set 22 mm (when wall is not deep
enough)#13593000
• Extension Set 22 mm (when wall is not deep
enough) #15597000
• levelling set 1° #95521000
Cleaning (see page 18)
Operation (see page 9)
+

5
English
Assembly (see page 6)
Fault Cause Remedy
Insufficient water - Supply pressure inadequate - Check water pressure (If a pump
has been installed check to see if
the pump is working).
- Regulator filter dirty - Clean filter in front of the mixer and
on the MTC-thermo cartridge
- Shower filter seal dirty
- filter insert shower dirty
- Clean filter seal between shower
and hose
- Clean filter insert between shower
and hose
Crossflow, hot water being forced
into cold water pipe, or vice versa,
when mixer is closed
- Backflow preventers dirty or
leaking
- Clean backflow preventers,
exchange if necessary
Spout temperature does not
correspond with temperature set
- Thermostat has not been adjusted - Adjust thermostat
- Hot water temperature too low - Increase hot water temperature to
42 ºC to 60 ºC
Temperature regulation not possible - thermo cartridge calcified - Exchange thermo cartridge
- For new installations: basic body
incorrectly connected (should be:
cold right, hot left) or installed with
180º rotation
- Install function block turned through
180º
Safety stop button not operating - Spring defective
- Button calcified
- Clean spring and/or button,
exchange if necessary
Valve stiff - Shut-off unit damaged - Exchange shut-off unit
Shower or spout dripping - Dirt or sedimentation on valve seat,
shut-off unit damaged
- Clean or exchange shut-off unit

6
2.
3.
1.
SW 4 mm
(5 Nm)
X + 11
X
1 - 2 mm
01800187
2.
1.
1
2 3
4 5
Montage

7
40
°C
40
°C
40
°C
40
°C
2.
(0,1 Nm)
40
°C
SW 3 mm
(4 Nm)
Armaturenfett
Grease
䀵滑油
1.
2.
Armaturenfett
Grease
䀵滑油
1.
6 7
8 9
10
Montage

8
40
°C
40
°C
SW 3 mm
40
°C
SW 3 mm
(2 Nm)
°C
40
40
°C
40
°C
Ecostat E
15707007
40
°C
Ecostat Square
15712007
1.
2.
1.
2.
3.
11b11a
12 13
14 15
Montage

9
40
°C
40
°C
>40° C
40
°C
1.
2.
40
°C
关 / close开 / open
热 / hot 冷 / cold
Bedienung

10
40
°C
40
°C
40
°C
例如 42° C
for example 42° C
40
°C
3.
2.
SW 3 mm
2.
1.
40
°C
1.
1 2
3 4
1 2 3
Justierung / Safety Function