Hans Grohe Raindance 180 Showerpipe 27212000 Manual

ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 4
Lesezeichen
中文 2
English 4
Raindance 240 Showerpipe
27216000
Raindance 180 Showerpipe
27212000

2
中文
安全技巧
装配时为避免挤压和切割受伤，必须戴上手
套。
本产品只允许作为洗浴、卫生和洁身之用。
头顶花洒夹持杆只为夹持头顶花洒而设计，不
得让其承载其它物品！
不得让儿童和肢体、精神和/或意识有障碍的
成人在不受监管的情况下使用淋浴系统。受酒
精或毒品影响的人员不得使用淋浴系统。
必须避免让身体敏感部位（如眼睛）接触到莲
蓬头喷水。必须保持莲蓬头与人头之间有足够
的距离。
该产品不得作扶柄使用。必须安装单独的扶
柄。
冷热水管间过大的压力差必须予以平衡。
安装提示
• 安装前必须检查产品是否受到运输损害。安装
后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗
和检查。
• 请遵守当地国家现行的安装规定。
• 本安装说明中所规定的安装尺寸理想用于身高
1700mm左右的人士。尺寸可根据需要进行修
改。在这种情况下，您必须留意，如果安装高
度改变，则花洒到地板的最小高度也随之改
变，且必须考虑到连接尺寸的改变。
• 由有资格的专业人员进行产品安装时请注意：
在所有加固区域中，加固表面是否平整（无突
出的接缝或瓷砖），墙体结构是否适合产品安
装且未显露出任何缺点。
• 必须装上花洒所附带的滤网密封垫，以过滤管
道里的杂质污物。杂质污物会影响花洒的功能
和/或损坏花洒的功能部件，由此而产生的产
品损坏不属于汉斯格雅的保修范围。
• 本产品并非设计来与蒸气浴连接使用！
• 紧急情况下,可使用细的锯子将下方区域中阀门
与头顶莲蓬头之间的管子锯短。
• 如果连续流热水器导致任何问题，或者出现了
不同的水压，您必须在冷水端安装水流限制器
（单独订购，商品编号97510000）。
技术参数
工作压强： 最大1MPa
27212000推荐工作压强： 0,1-0,5MPa
27216000推荐工作压强： 0,15-0,5MPa
测试压强： 1,6MPa
 (1MPa=10bar=147PSI)
热水温度： 最大70°C
推荐热水温度： 65°C
中心距离： 150±12mm
连接管线G1/2: 左热右冷
热力消毒: 最大70°C/4分钟
• 自动防止回流
• 该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
安全功能 (参见第页11 )
恒温阀芯的安全功能可以预先设定所希望的最高
出水温度，例如最高温度为42℃
调节 (参见第页10)
安装完成后必须检查调温器的出水温度。如在取
水处测量所得的温度与调温器上设定的温度有偏
差，那么必须进行调整。
保养 (参见第页16)
• 单向阀必须在符合国家或当地的法律的情况下
按照DINEN1717定期检查（至少一年一次）。
• 为了保证恒温器的稳定运转，请务必定期从最
热到最冷转动调温器。
大小 (参见第页12)
流量示意图 (参见第页24)
顶置花洒
手持花洒
备用零件 (参见第页23)
选装附件 (不在供货范围内)
匹配瓷砖的圆盘镀铬
#98681000(参见第页23)
清洗 (参见第页18)
操作 (参见第页14)
请在使用喷头后略微倾斜，排空其中水分。

3
中文
安装 (参见第页6)
问题 原因 补救
龙头出水量小 - 水压不足 - 检查总水压
- 调压器过滤网脏污 - 清洁龙头前面和恒温阀芯的过
滤网。
- 花洒滤网有垃圾堵塞 - 清洗花洒和软管间的过滤网
串水，在龙头关闭的状态下，热
水被强迫流入冷水管路，或者相
反。
- 单向阀有垃圾堵塞或漏水 - 清洗单向阀，如有必要则更换
新的
龙头出水温度和温度设定的不符 - 恒温阀芯未被调节 - 调节恒温器
- 热水温度过低 - 将热水温度从42ºC升高到65ºC
水温无法调节 - 恒温阀芯表面结垢 - 更换-恒温阀芯
使用恒温龙头后，燃气热水器不
工作
- 过滤网有垃圾堵塞 - 清洗过滤网/更换过滤网
- 单向阀装反 - 正确安装单向阀
- 手持花洒的流量限制器没有去
除
- 去除流量限制器

4
English
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The product may only be used for bathing, hygienic
and body cleaning purposes.
The arm of the shower head is intended only to hold
the shower head. Do not load it down with other
objects!
Children as well as adults with physical, mental and/
or sensoric impairments must not use this product
without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from
using this product.
Do not allow the streams of the shower touch
sensitive body parts (such as your eyes). An
adequate distance must be kept between the shower
and you.
The product may not be used as a holding handle. A
separate handle must be installed.
The hot and cold supplies must be of equal
pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
• The installation dimensions stated in these installation
instructions are ideal for people of approximately
1700 mm in body height. The dimensions can be
altered if required. In this case, pay attention to the
fact that a change of installation height will also
change the minimum height, and that the altered
mounting dimensions must be taken into considera-
tion.
• During installation of the product by qualified trained
personnel, make sure that the entire fastening surface
is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply
the product and has no weak points.
• The mesh washer must be insert to protect the shower
against incoming dirt by pipework. Incoming dirt
leads to defects or/and can damage parts of the
shower; such caused faults voids all liability and
guarantee claims.
• The product is not designed to be used with steam
baths!
• If required, the bottom part of the pipe between the
fixture and the shower head can be shortened with a
fine-toothed saw.
• If the continuous water heater causes any problems,
or you have different water pressures you must install
a water limiter to the cold supply, (ordered
separately,article number 97510000).
Technical Data
Operating pressure: max. 1 MPa
27212000 Recommended operating
pressure: 0,1 - 0,5 MPa
27216000 Recommended operating
pressure: 0,15 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Centre distance: 150±12 mm
Connections G 1/2: cold right - hot left
Thermal disinfection: max. 70°C / 4 min
• Safety against backflow
• The product is exclusively designed for drinking
water!
Symbol description
Do not use silicone containing acetic acid!
Safety Function (see page 11 )
The desired maximum temperature for example max.
42º C can be pre-set thanks to the safety function.
Adjustment (see page 10)
After the installation, the output temperature of the
thermostat must be checked. A correction is necessary if
the temperature measured at the output differs from the
temperature set on the thermostat.
Maintenance (see page 16)
• The check valves must be checked regularly
according to DIN EN 1717 in accordance with
national or regional regulations (at least once a
year).
• To guarantee the smooth running of the thermostat, it
is necessary from time to time to turn the thermostat
from total hot to total cold.
Dimensions (see page 12)
Flow diagram (see page 24)
 Overhead shower
 Hand shower

5
English
Assembly (see page 6)
Spare parts (see page 23)
Special accessories (order as an extra)
tile-matching-disk Chrome Plated
#98681000 (see page 23)
Cleaning (see page 18)
Operation (see page 14)
To empty the overhead shower after use, hold it in a
slightly inclined position.
Fault Cause Remedy
Insufficient water - Supply pressure inadequate - Check water pressure (If a pump
has been installed check to see if
the pump is working).
- Regulator filter dirty - Clean filter in front of the mixer and
on the MTC-thermo cartridge
- Shower filter seal dirty - Clean filter seal between shower
and hose
Crossflow, hot water being forced
into cold water pipe, or vice versa,
when mixer is closed
- Backflow preventers dirty or leak-
ing
- Clean backflow preventers, ex-
change if necessary
Spout temperature does not
correspond with temperature set
- Thermostat has not been adjusted - Adjust thermostat
- Hot water temperature too low - Increase hot water temperature to
42 ºC to 65 ºC
Temperature regulation not possible - thermo cartridge calcified - Exchange thermo cartridge
Instantaneous heater didn't work
with thermostat
- Filters are dirty - Clean the filter / exchange filter
- check valve hasn't moved back - Exchange check valves
- Flow limiter in handshower isn’t re-
moved
- Remove flow limiter

6
1.
2.
X + 36 mm
X 36
X
1. 2.
Silicone
1 2
36 mm
3a 3b
max.
39 mm
max.
5 mm
SW 24 mm
4 5
Montage

7
1.
2.
2.
3.
1.
SW 30 mm
(17 Nm)
6 7
8 9
10 11
Montage

8
60 mm
Ø 6 mm
1.
2.
3.
SW 8 mm
Silicone
12 13
14 15
16
Montage

9
1.
2. SW 3 mm
(6 Nm)
SW 8 mm
17 18
19
20
94246000
21
22
SW 2 mm
(1 Nm)
SW 17 mm
(10 Nm)
Montage

10
SW 3 mm
1.
2.
1
3
2
1. 2.
SW 3 mm
(2 Nm)
Justierung

11
z. B. 42°C
for example 42°C
3
2
5 6
4
SW 3 mm
1.
2.
1
SW 3 mm
(2 Nm)
1.
2.
2
1.
2.
2.
1.
Safety FunctionSafety Function

12
232
min. 2115
2065
1025
1025
1000
1925
Raindance 180 Showerpipe 27212000
Maße

13
26°
26°
Ø 236
96
1000 1025
min. 2115
Ø 39
276
1925
1025
65
105
80
Ø 80
212
439
545
2065
65
Ø 68
283
100
Raindance 240 Showerpipe 27216000
Maße

14
2.
1.
开/open
关 / close
1.
2.
Bedienung

15
>40°C
1 2a 2b
2.
1.
Raindance Select S 120
26531007
RainAir Rain WhirlAir
Croma Select S Multi
26801407
Intense
Rain
Massage SoftRain
冷 / cold
热/hot
2.
1.
Bedienung

16
1SW 3 mm
2.
3.
4.
1.
SW 30 mm
2
SW 10 mm
3
5
4
SW 10 mm
(20 Nm)
红色 ⁄ red
Wartung

17
6
SW 30 mm
(17 Nm)
4.
3.
7
5.
2.
1.
SW 3 mm
(6 Nm)
Wartung

18
Reinigung
重要说明
肥皂，洗发水、沐浴液、染发剂、香水、刮胡水、
指甲油的残留也会对产品造成损伤。
此处：使用后要小心地用清水将剩余物冲洗干净。
同样在产品下方不得存放洗涤剂和化学药品，例如
不可放在用于洗脸盆的梳洗柜中否则挥发气体将
损坏产品。
在已经损伤的表面继续使用清洁剂会给表面造成更
大的损伤。
表面损坏的部件必须更换，否则会有受伤
的危险。
不按规定进行清洁而造成的任何损坏不在本公司产
品保修范围之内。
QuickClean
有了QuickClean，手工清洁功能，要去掉喷头上的
水垢，只需简单地搓除即可。
担保
Hansgrohe向用户保证，该产品无制
造缺陷。如果自购买之日起五年内出现缺
陷，Hansgrohe将免费排除。保证条件和详情见
www.hansgrohe-int.com/guarantee。在提出保修的
权利时请联系您的合同方。本保证不涉及有关国
家法律规定的消费权
汉斯格雅产品的清洁建议
现代的卫浴龙头、厨房龙头、花洒、配件、盥洗
台、浴盆和加热器采用的制造材料非常迥异，以适
应产品外形设计和使用功能的市场需求。
为了避免产品损坏和由此引发的投诉及争议，必须
在使用和清洁产品时遵循有关规程。
在保养汉斯格雅产品时，原则上必须注意：
• 只能使用那些有明确注明是适用于本产品的清
洁剂。
• 不允许使用含有盐酸、蚁酸、氯漂或醋酸的清
洁剂，因为这些清洁剂会给产品表面造成严重的
损伤。
• 含磷酸的清洁剂必须在特定条件下使用。
• 不允许将两种以上清洁剂混合使用。
• 不允许使用具有研磨作用的清洁工具和设备，如
不适合的清洁粉末、海绵垫或超细麦克布。
• 必须严格遵守清洁剂生产厂商的使用说明。
• 严格遵守清洁剂的用量和作用时间，决不允许清
洁剂的作用时间长于规定值。
• 定期的清洁以预防水垢。
• 不允许将清洁剂直接喷射到汉斯格雅产品上，因
为喷雾会进入汉斯格雅产品的开口部分和缝隙中
而造成损害。首先将清洁剂喷在软布上，再用软
布进行清洁。
• 清洁之后必须用足够的清水冲洗，以彻底去除残
留的吸附物（清洁剂）。
• 不允许使用蒸汽清洗机，高温会损害产品。
中文
QUICK
CLEAN

19
• After cleaning rinse thoroughly with clean water to
remove any cleaner residue.
• The use of steam cleaners is not permitted. The high
temperatures can damage the products.
Important
Residues of toiletries such as liquid soaps, shampoos and
shower gels, hair dyes, perfumes, aftershave and nail
varnish can also cause damage.
Here too: Carefully rinse with water after use to remove residues.
Likewise, do not store any cleaning agents or chemicals
under the products, for example in a vanity unit, as the
vapours may damage the products.
The damage of already damaged surfaces will
deteriorate under the effect of the cleansers.
Components with damaged surfaces
must be exchanged, otherwise there
could be an injury danger.
Damage caused by improper treatment will not be
covered by our guarantee.
QuickClean
The QuickClean cleaning function only needs a small
manual rub over to remove the lime scale from the spray
channels.
Warranty
Hansgrohe guarantees to the consumer that this product is free
of production faults. If evertheless any defect is detected within
5 years from date of purchase, Hansgrohe will remedy this
defect free of charge. You will find the conditions and details
of this guarantee at www.hansgrohe-int.com/guarantee.
Please contact your contracting party to claim your rights
under this guarantee. This guarantee does not affect the
customer‘s rights under the respective national legislation.
Cleaning Recommendation for
Hansgrohe Products
Today, modern sanitary and kitchen tapware, showers,
accessories, washstands, tubs and radiators consist of
very different materials to comply with the needs of the
market with regard to design and functionality.
To avoid damage and reclamations, it is necessary to
consider certain criteria when cleaning.
With regard to caring for the
Hansgrohe products, the following
must in principle be heeded:
• Only use cleaning material which is explicitly provided
for this type of application.
• Never use cleaning materials, which contain
hydrochloric acid, formic acid, chlorine pale lye or
acetic acid, as they cause considerable damage.
• Phosphorus acidic cleaners are only conditionally applicable.
• Mixing cleaning agents is not permitted, generally.
• Never use cleaning materials or appliances with an
abrasive effect, such as unsuitable cleaning powders,
sponge pads or micro fibre cloths.
• The instructions of the cleaning agent manufacturers
have to be followed absolutely.
• Cleaning has to be carried out with a specified cleaner
dosage, contact time, object-related and adapted to the needs.
• The building up of calcifications has to be removed by
cleaning regulary.
• When using spray cleaners, spray the cleaning solution onto
a soft cloth or sponge, never directly onto the Hansgrohe
products, as the atomised spray could enter openings and
gaps in the Hansgrohe products and cause damage.
English
QUICK
CLEAN

20
4
5 6
SW 2 mm
1 2
3
SW 17 mm
SW 17 mm
(10 Nm)
Reinigung