Hanwha Techwin WISENET SCB-6005 User manual

High Resolution Box Camera
User Manual
SCB-6005

High Resolution Box Camera
User Manual
Copyright
©2020 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks
mentioned in this manual are the registered trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be
reproduced, distributed or changed, partially or wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents
in this document, but no formal guarantee shall be provided. Use of this document and the
subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin
reserves the right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.

English_3
●SAFETY INFORMATION
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING
• To prevent damage which may result in fire or electric shock hazard, do not expose this
appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with
the installation instructions.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. insecure connection may cause
fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.

4_ safety information
safety information
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers
filled with water on top of the camera. doing so may cause personal injury due to fire,
electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or electric
shock.
8. If any unusual smells or smoke come from the unit, stop using the product. in such case,
immediately disconnect the power source and contact the service center. continued use in
such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. never
disassemble or modify this product in any way. (Hanwha Techwin is not liable for problems
caused by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. doing so may cause
fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location
subject to excessive vibrationor magnetic interference.
2. Do not install in a location subject to high temperature (over 55°C), low temperature
(below -10°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so
may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may
damage the CMOS image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CMOS.

English_5
●SAFETY INFORMATION
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health
or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

6_important safety instructions
important safety instructions
Other Notes
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong is provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving
the cart/ apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. If you use excessive force when installing the product, the camera may be damaged and
malfunction.
If you forcibly install the product using non-compliant tools, the product may be damaged.

English_7
●IMPORTANT SAFETY INSTRUCTIONS
16. Do not install the product in a place where chemical substances or oil mist exists or may
be generated. As edible oils such as soybean oil may damage or warp the product, do not
install the product in the kitchen or near the kitchen table.
This may cause damage to the product.
17. When installing the product, be careful not to allow the surface of the product to be
stained with chemical substance.
Some chemical solvents such as cleaner or adhesives may cause serious damage to the
product’s surface.
18. If you install/disassemble the product in a manner that has not been recommended, the
production functions/performance may not be guaranteed.
Install the product by referring to “Installation & connection” in the user manual.
19. Installing or using the product in water can cause serious damage to the product.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
Hanwha Techwin cares for the environment at all product manufacturing
stages, and is taking measures to provide customers with more
environmentally friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating
environmentally friendly products, and indicates that the product satisfies
the EU RoHS Directive.

8_ contents
contents
INTRODUCTION
9
9 Features
10 Components and Accessories
11 Overview
13 Lens
CONNECTION
16
16 Connecting to Monitor
16 Connecting to Power
17 Control via RS-485 Interface
18 To connect the Day & Night
Input
18 To connect the Motion
Detection Output
19 Using Coaxial Communications
CAMERA OPERATION
20
20 Menu Conguration
20 Menu Setup
TROUBLESHOOTING
34
34 Troubleshooting

English_9
●INTRODUCTION
introduction
FEATURES
yHigh Resolution
Use of a 2 mega pixel CMOS device provides clear pictures with a resolution of 1945x1097.
yExcellent Sensitivity
The built-in high sensitivity COLOR CMOS produces a clear image.
- Color : 0.04Lux (F1.2, 1/30sec)
BW: 0.004Lux(F1.2)
ySSNR4 Function
High performance DSP chip removes noises of GAIN resulting from the low light level and
shows a vivid, high definition video even in the dark place.
yDay&Night
This camera has a function that automatically selects the mode that is appropriate
for daytime or night-time conditions. The COLOR mode operates in daytime condi-
tions to provide optimum colors, and B/W mode operates in night-time conditions
to enhance the definition of the image.
yPROFILE
You can set a mode according to the camera installation conditions.
- BASIC, DAYNIGHT, BACKLIGHT, ITS, INDOOR, USER
yDWDR
By adopting a proprietary high performance DSP chip, the camera delivers clear,
high quality pictures even in backlight, by increasing exposure in dark areas while
decreasing it in bright areas; a corrected image with clear details results.
yDC Drive Lens Support
You can select Manual or DC Drive Lens from the menu.
yMiscellaneous Functions
HLC(High Light Compensation), REVERSE , SHARPNESS and PRIVACY functions are
provided.
yCommunication
Coaxial and RS-485 communication methods are supported.
- Coaxial Communications: ACP(AHD), Pelco-C(CVBS)
- RS-485 Communications : SAMSUNG-T, HONEYWELL, BOSCH, PELCO-P, PELCO-D

10_ introduction
introduction
COMPONENTS AND ACCESSORIES
Check if the following items are included in the product package.
High Resolution Box Camera
User Manual
SCB-6005
Camera User Manual
Terminal Block Sheets lens mount

English_11
●INTRODUCTION
OVERVIEW
Front View
❶
Tripod Mounting Bracket Screw Hole :
`Used to fix the camera on a bracket.
The screw sizes for this hole are as follows.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard), or 0.197"
(ASA standard)
2
Lens adaptor : IInstall this if you use the lens.
3
Auto Iris Lens Connector : Used to connect Auto Iris Lens plug.
M
`Auto shutter adaptor, c-mount adaptor and supporting board are not provided with the
camera.
Please check the installed documentation of tripod for the installation of cameras.
2
3
1

12_ introduction
introduction
Rear View
POWER
VIDEO
➊
➌
➋
➍
➎
➏
➐
➑
1 Function Setup switch
Press the Function Setup switch briey to display the menu screen.
After the menu is displayed on the screen, move the cursor <up/down/left/right> to
select the desired item or to change the value or status.
Switching between AHD and CVBS modes: Press the SET button for more than 5 seconds.
2 Power LED : This lamp is lit when the camera is receiving power normally.
3 Video OUT Terminal : Sends video signal and connects to the Video IN port of a AHD DVR.
4 Power input terminal : Connect the designated power supplies.
5 RS-485 Control Port : You can control SETUP MENU through this port by using
external controllers like a Remote controller that RS-485
Communication is supported.
6 D & N Input Port : You can switch to Day & Night Mode by connecting an external
signal to this port.
7 MD Output Port : Motion detection signals are output through this port.
8 GND
Num Name I/O Direction
1RS-485+ I/O
2RS-485- I/O
3DN I
4MD O
5GND -
 External I / O port configuration

English_13
●INTRODUCTION
LENS
The lens is not supplied with this camera. Purchase a lens suitable for your environment.
This camera accepts the auto iris lens and both C-and CS-mount lens.
M
` To use the functions of this camera effectively it is recommended that a DC type Auto Iris
lens is used.
`Keep the lens surface clean, if it becomes contaminated with dirt or fingerprints the picture
quality suffers.
When Using Auto Iris Lens
1. Remove the protective glass cover
from the front of the camera, and
fasten the auto iris lens by turning it
clockwise.
2. After combining the lens, adjust the
focus.
3. If you cannot focus, insert one to three sheets (provided as accessories)
between the camera and the lens, and then reassemble and focus.
NEAR
TELE
M
e
g
a
P
i
e
x

14_ introduction
introduction
When Using a C/CS-Mount lens (Not included)
Before installing a lens, identify whether the lens to be installed is a C-Mount or CS-Mount.
This camera is set for a CS-Mount Lens by default. To install a C-Mount Lens, a simple
modification is required.
yWhen Using a CS-Mount Lens
Remove the protective glass cover at the
front of this product and turn the CS-
Mount Lens clockwise to install it.
M
`Use the lens connector shown in the following
figure. If the dimensions of the connector are not
correct, it may damage the camera, or the lens
may not be installed firmly.
`If the lens is too heavy, the camera becomes
unbalanced and there may be problems. Use a lens
that weighs less than 450g.
`When adjusting the Automatic Level Control
(ALC) of an auto iris lens, use Av mode if available.
If you use the Pk mode, the picture brightness
may change continuously.
C-Mount Lens: 10mm or less
CS-Mount Lens: 5mm or less

English_15
●INTRODUCTION
yWhen Using a C-Mount Lens
1. Remove the protective glass cover
at the front of this product and turn
the C-Mount Adapter clockwise to
install it.
2. Turn the C-Mount lens clockwise
to install it.
3. After combining the lens, adjust the focus.
4. If you cannot focus, insert one to three sheets (provided as accessories) between
the camera and the lens, and then reassemble and focus.
C-Mount Adapter
(Not included)
C-Mount Adapter
(Not included)

16_ connection
connection
CONNECTING TO MONITOR
Connect the Video OUT port on the rear panel of the camera to a AHD DVR.
yAs the connecting method varies with the instruments, refer to the manual supplied
with the instrument.
yOnly connect the cable when the power is turned o.
CONNECTING TO POWER
You can connect power as shown in the following figure.
Since the power specification supports both AC and
DC, connect AC 24V, 500mA Adaptor or DC 12V,
500mA Adaptor.
POWER
VIDEO
POWER
VIDEO
RE CHD DALAR M NETWOR K BACKUP POWE R
SCB-6005
AHD DVR
Monitor

English_17
●CONNECTION
When the resistance value of copper wire is at [20°C(68°F)]
Copper wire size (AWG) #24 (0.22mm2)#22 (0.33mm2)#20 (0.52mm2)#18 (0.83mm2)
Resistance value(Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
yAs shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to the camera
may aect the performance of the camera.
 Standard voltage for camera operation : DC 12V±10%, AC 24V±10%
 There may be some deviation in voltage drop depending on the type of wire and the
manufacturer.
M
`Be sure to connect power only after all the installation is complete.
CONTROL VIA RS485 INTERFACE
The camera can be controlled by using external controllers like a Remote controller. (RS-485
Communication)
(1) To control by PC
Connect the RS-485 control port of the camera and the serial cable through an RS-485
converter.
Example) PC Serial Port Serial Cable RS-485 Converter Camera RS-485Control Port.
(2) To control using a DVR or System Controller
Connect the RS-485 cable (TRX+, TRX-) to the connection port of the 485 control board that is
connected to the DVR or System Controller.
485 Control Board Connection Port RS-485 Control Port
(+) CONNECTIONTERMINAL (TRX+) 485+
(- ) CONNECTIONTERMINAL (TRX-) 485-
* RS-485 Communication establishment initial value
Item Camera ID BAUD RATE UART MODE RET PKT
Initial value
19600 NONE DISABLE
M
` To control the camera by constructing an additional controller, use the SAMSUNG-T,
HONEYWELL, BOSCH, PELCO-P, PELCO-D protocol.

connection
18_ connection
TO CONNECT THE DAY & NIGHT INPUT
Connect one strand of each signal line (2-strand) of the Illumination Sensor to the [DN] port,
and connect the other strand to the [GND] port.
yD/N switch input wiring diagram
Sensor
GND
RESISTORDN (5mA SINK)
RESISTOR RESISTOR
VCC_3.3V
DIODE
GND
MLCC TRANSISTOR
External
connection
Inside of the camera
TO CONNECT THE MOTION DETECTION OUTPUT
If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are
connected by using the open collector method, it may cause malfunction.
Refer to the connection diagram below when connecting devices that exceed the voltage and
current specifications.
yConnection example
Warning lamp
/ Siren power
Warning lamp /
Siren
( - ) ( + )
MD Alarm out (12VDC 20mA MAX)
RESISTOR 10K ohm
DIODE
RELAY
DC 5V or 3.3V
TRANSISTOR
GND
GND
TRANSISTOR
External connection Inside of the camera
GND
RESISTOR

English_19
●CONNECTION
Distance Recommended Cable Specification
500m 5C2V
MM`It is recommended that pure copper coax cable is used and not copper coated steel, as
this will cause issues with the communication over the coaxial cable.
USING COAXIAL COMMUNICATIONS
yCoaxial Communications System
yOSD Control method
CAMERA DVR CONTROLLER
SET MENU/ENTER OSD KEY
UP UP KEY JOYSTICK UP
DOWN DOWN KEY JOYSTICK DOWN
LEFT LEFT KEY JOYSTICK LEFT
RIGHT RIGHT KEY JOYSTICK RIGHT
- Video Cable
The camera's video output port is connected to the monitor with a BNC coaxial
cable, shown below.
RE CHD DALAR M NETWOR KBACKUP POWE R
Coaxial

20_ camera operation
MENU CONFIGURATION
MAIN SETUP
VIDEO FORMAT
◦AHD ◦CVBS
PROFILE
◦BASIC ◦DAY/NIGHT ◦BACKLIGHT
◦ITS ◦INDOOR ◦USER
WHITE BAL
◦ATW ◦OUTDOOR ◦INDOOR
◦MANUAL ◦ AWC →SET
EXPOSURE
◦BRIGHTNESS ◦LENS ◦SHUTTER
◦AGC ◦SSNR4 ◦DWDR
◦RETURN
BACKLIGHT
◦OFF ◦USER BLC ◦HLC
SPECIAL
◦DISPLAY ◦COMM ADJ ◦IMAGE ADJ
◦DAY/NIGHT ◦DEFOG ◦PRIVACY
◦MOTION ◦RETURN
EXIT
◦SAVE ◦NOT SAVE ◦RESET
MENU SETUP
Use the Function Setup switch within the camera.
camera operation
POWER
VIDEO
Function Setup switch