HANYOUNG NUX HD6 User manual
－
DANGERWARNINGCAUTION
DANGER
WARNING
CAUTION
HD6
HANYOUNGNUX CO.,LTD
·Operation: oPE.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
·Operation: oPE.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : 10(Sec)
·Operation: OFF time after output ON time of oPE.2
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: CLo.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : (10 Sec)
Operation: CLo.2 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: OFF time after output ON time of oPE.1
·Setting value change( , ) : 1 ~ 999
Default : oFF
Default : PL.1
Default : 0℃
Default : 5.0℃
Default : sec
Default : Min
Default
(10 Sec)
Default
(10 Sec)
Default
(1 Min)
Default
(1 Min)
온도설정
시간설정
프로그램설정
Open 1 operation ON time
Open 1 operation OFF time
Closing 1 operation ON time
Closing 1 operation OFF time
Open 2 operation ON time
Open 2 operation OFF time
Closed 2 operation ON time
Closed 2 operation OFF time
Save time setting value
※ Press for more than 3 seconds.
(Enter the mode or save the set value)
on (lock): locks all set values in program setting mode
oFF (Release): Unlock all set values in program setting mode
Setting data lock function
·“PL.2”: 1st and 2nd stage setting and 1st and 2nd stage control (control 2nd stage priority)
·“PL.1”: 1st stage setting and 1st stage control only
Control method selection (1st stage control operation or 2nd stage control operation)
·Temperature compensation for sensor line length or error occurrence (-10.0 ~ 10.0 ℃)
Measurement value correction setting
·Constant deviation is required during ON/OFF operation (0.1 ~ 25.0 ℃)
Hysteresis
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output ON time unit
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output OFF time unit
Current
temperature
Current
temperature
Default :
30.0 ℃
Default :
10.0 ℃
Default :
10.0 ℃
Default :
-10.0 ℃
Save
temperature
setting value
※
In the program setting mode, “2. Displayed only when tyP = PL.2” is set.
※
※ When setting “2.tyP = PL.2” in program setting mode
The priority of the task is "2 tasks (2 open, 2 closed)".
Open 1 operation temperature setting
(Set temperature (oPE.1) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
(Set temperature (CLo.1) <present temperature (PV))
Closed 1 operating temperature setting
·Operation: Operates when the current temperature is lower
than the set temperature (CLo.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
Open 2 operation temperature setting
(Set temperature (oPE.1+oPE.2) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1 + oPE2)
·Setting value change( , ) : 1.0 ~ 130.0 ℃
Closed 2 operating temperature setting
(Set temperature (CLo.1 + CLo.2)> Current temperature (PV))
·Operation: Operates when the current temperature is lower than
the set temperature (CLo.1 + CLo.2)
·Setting value change( , ) : -1.0 ~ -99.0 ℃
Current
temperature
Current
temperature
Current
temperature
※
Displayed only when “2.tyP=PL.2”
is set in the program setting mode.
※
·Operation: oPE.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
·Operation: oPE.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : 10(Sec)
·Operation: OFF time after output ON time of oPE.2
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: CLo.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : (10 Sec)
Operation: CLo.2 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: OFF time after output ON time of oPE.1
·Setting value change( , ) : 1 ~ 999
Default : oFF
Default : PL.1
Default : 0℃
Default : 5.0℃
Default : sec
Default : Min
Default
(10 Sec)
Default
(10 Sec)
Default
(1 Min)
Default
(1 Min)
온도설정
시간설정
프로그램설정
Open 1 operation ON time
Open 1 operation OFF time
Closing 1 operation ON time
Closing 1 operation OFF time
Open 2 operation ON time
Open 2 operation OFF time
Closed 2 operation ON time
Closed 2 operation OFF time
Save time setting value
※ Press for more than 3 seconds.
(Enter the mode or save the set value)
on (lock): locks all set values in program setting mode
oFF (Release): Unlock all set values in program setting mode
Setting data lock function
·“PL.2”: 1st and 2nd stage setting and 1st and 2nd stage control (control 2nd stage priority)
·“PL.1”: 1st stage setting and 1st stage control only
Control method selection (1st stage control operation or 2nd stage control operation)
·Temperature compensation for sensor line length or error occurrence (-10.0 ~ 10.0 ℃)
Measurement value correction setting
·Constant deviation is required during ON/OFF operation (0.1 ~ 25.0 ℃)
Hysteresis
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output ON time unit
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output OFF time unit
Current
temperature
Current
temperature
Default :
30.0 ℃
Default :
10.0 ℃
Default :
10.0 ℃
Default :
-10.0 ℃
Save
temperature
setting value
※
In the program setting mode, “2. Displayed only when tyP = PL.2” is set.
※
※ When setting “2.tyP = PL.2” in program setting mode
The priority of the task is "2 tasks (2 open, 2 closed)".
Open 1 operation temperature setting
(Set temperature (oPE.1) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
(Set temperature (CLo.1) <present temperature (PV))
Closed 1 operating temperature setting
·Operation: Operates when the current temperature is lower
than the set temperature (CLo.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
Open 2 operation temperature setting
(Set temperature (oPE.1+oPE.2) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1 + oPE2)
·Setting value change( , ) : 1.0 ~ 130.0 ℃
Closed 2 operating temperature setting
(Set temperature (CLo.1 + CLo.2)> Current temperature (PV))
·Operation: Operates when the current temperature is lower than
the set temperature (CLo.1 + CLo.2)
·Setting value change( , ) : -1.0 ~ -99.0 ℃
Current
temperature
Current
temperature
Current
temperature
※
Displayed only when “2.tyP=PL.2”
is set in the program setting mode.
※
·Operation: oPE.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
·Operation: oPE.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : 10(Sec)
·Operation: OFF time after output ON time of oPE.2
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: CLo.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : (10 Sec)
Operation: CLo.2 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: OFF time after output ON time of oPE.1
·Setting value change( , ) : 1 ~ 999
Default : oFF
Default : PL.1
Default : 0℃
Default : 5.0℃
Default : sec
Default : Min
Default
(10 Sec)
Default
(10 Sec)
Default
(1 Min)
Default
(1 Min)
온도설정
시간설정
프로그램설정
Open 1 operation ON time
Open 1 operation OFF time
Closing 1 operation ON time
Closing 1 operation OFF time
Open 2 operation ON time
Open 2 operation OFF time
Closed 2 operation ON time
Closed 2 operation OFF time
Save time setting value
※ Press for more than 3 seconds.
(Enter the mode or save the set value)
on (lock): locks all set values in program setting mode
oFF (Release): Unlock all set values in program setting mode
Setting data lock function
·“PL.2”: 1st and 2nd stage setting and 1st and 2nd stage control (control 2nd stage priority)
·“PL.1”: 1st stage setting and 1st stage control only
Control method selection (1st stage control operation or 2nd stage control operation)
·Temperature compensation for sensor line length or error occurrence (-10.0 ~ 10.0 ℃)
Measurement value correction setting
·Constant deviation is required during ON/OFF operation (0.1 ~ 25.0 ℃)
Hysteresis
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output ON time unit
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output OFF time unit
Current
temperature
Current
temperature
Default :
30.0 ℃
Default :
10.0 ℃
Default :
10.0 ℃
Default :
-10.0 ℃
Save
temperature
setting value
※
In the program setting mode, “2. Displayed only when tyP = PL.2” is set.
※
※ When setting “2.tyP = PL.2” in program setting mode
The priority of the task is "2 tasks (2 open, 2 closed)".
Open 1 operation temperature setting
(Set temperature (oPE.1) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
(Set temperature (CLo.1) <present temperature (PV))
Closed 1 operating temperature setting
·Operation: Operates when the current temperature is lower
than the set temperature (CLo.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
Open 2 operation temperature setting
(Set temperature (oPE.1+oPE.2) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1 + oPE2)
·Setting value change( , ) : 1.0 ~ 130.0 ℃
Closed 2 operating temperature setting
(Set temperature (CLo.1 + CLo.2)> Current temperature (PV))
·Operation: Operates when the current temperature is lower than
the set temperature (CLo.1 + CLo.2)
·Setting value change( , ) : -1.0 ~ -99.0 ℃
Current
temperature
Current
temperature
Current
temperature
※
Displayed only when “2.tyP=PL.2”
is set in the program setting mode.
※
Other HANYOUNG NUX Temperature Controllers manuals
HANYOUNG NUX
HANYOUNG NUX HY-1000 User manual
HANYOUNG NUX
HANYOUNG NUX HY-1000 User manual
HANYOUNG NUX
HANYOUNG NUX NP200 User manual
HANYOUNG NUX
HANYOUNG NUX TH500A User manual
HANYOUNG NUX
HANYOUNG NUX ML-E User manual
HANYOUNG NUX
HANYOUNG NUX BR6 User manual
HANYOUNG NUX
HANYOUNG NUX BR6A User manual
HANYOUNG NUX
HANYOUNG NUX RS6 User manual
HANYOUNG NUX
HANYOUNG NUX DX Series User manual
HANYOUNG NUX
HANYOUNG NUX ND4 User manual
HANYOUNG NUX
HANYOUNG NUX HY-1000 User manual
HANYOUNG NUX
HANYOUNG NUX HY-4500 User manual
HANYOUNG NUX
HANYOUNG NUX ND4 User manual
HANYOUNG NUX
HANYOUNG NUX BX8 User manual
HANYOUNG NUX
HANYOUNG NUX TD510 Series User manual
HANYOUNG NUX
HANYOUNG NUX ML-D2H User manual
HANYOUNG NUX
HANYOUNG NUX DF4 User manual
HANYOUNG NUX
HANYOUNG NUX DX Series User manual
HANYOUNG NUX
HANYOUNG NUX BX8 User manual
HANYOUNG NUX
HANYOUNG NUX ML-D Series User manual
Popular Temperature Controllers manuals by other brands
Carrier
Carrier Infinity SYSTXCCUIZ01 Installation and start-up instructions
MDT Technologies
MDT Technologies SCN-RT2UP.01 manual
Crestron
Crestron CHVI-RTS-1G-N installation guide
Viconics
Viconics VTR8300 Series Application guide
Cisco
Cisco Meraki MT10 installation guide
Burkert
Burkert 8625 operating instructions
HB-THERM
HB-THERM M8150-EN Assembly instructions
Eurotherm
Eurotherm 2108i Installing and operating instructions
Honeywell
Honeywell T775J Product data
TE Technology
TE Technology TC-24-10 instruction manual
Wolf Steel
Wolf Steel Condo Pack Installation and operating instructions
Ascon tecnologic
Ascon tecnologic TRH04 user manual