Harbor Freight Tools 97966 User manual

Page 1SKU 9766-67 For technical questions, please call 1-800-444-3353.
5 PIECE CAB MOUNTED LIGHT
INSTRUCTIONS AND PRECAUTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
READ ALL PRECAUTIONS AND INSTRUCTIONS.
Copyright©2008 by Harbor Freight Tools®. All rights reserved. No portion of this document
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools. Diagrams within this document may not
be drawn proportionally. Due to continuing improvements, actual product may differ slightly
from the product described herein.
For technical questions or replacement parts, please call
1-800-444-3353.
Model
97966
97967
UNPACKING
If any parts are missing or broken,
please call Harbor Freight Tools at the num-
ber shown on the cover of this document as
soon as possible.
IMPORTANT SAFETY
INFORMATION
Assembly Precautions
Install only according to these instruc-1.
tions. Improper installation can create
hazards.
Wear ANSI-approved safety goggles2.
and heavy-duty work gloves during
assembly.
Keep installation area clean and well lit.3.
Keep bystanders out of the area during4.
installation.
Do not install when tired or when under5.
the inuence of drugs or medication.
Use Precautions
This product is not a toy. Do not allow1.
children to play with this item.
Use for intended purpose(s) only.2.
Inspect before use; do not use if parts3.
loose or damaged.
Application of this product must meet4.
State and DOT requirements for vehicle
lighting.
Turn vehicle off and disconnect the bat-5.
tery before installation.
WARNING: The brass components6.
of this product contain lead, a chemi-
cal known to the State of California to
cause birth defects (or other reproduc-
tive harm). (California Health & Safety
code § 25249.5, et seq.)
Maintain product labels and name-7.
plates. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.

Page 2SKU 9766-67 For technical questions, please call 1-800-444-3353.
ASSEMBLY INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of
this document including all
text under subheadings
therein before set up or use of
this product.
Installation
The planned mounting area must1.
provide a ush t to the bottom of the
Lights (1).
Remove the lens from each Light and2.
use the base of the Light as a template
to mark mounting holes.
Ensure that the installation area has no3.
hidden electrical or stereo lines before
drilling.
Drill the holes, then secure each of4.
the Lights with two Long Screws (2).
Replace the lens.
See Wiring Diagram, page 4.5.
Connect the wire of each of the Lights6.
to the Lead Wire (8) using a Wire
Splice (4). Insert the two wires into the
holes of the Splice and use pliers (not
included) to push down the metal tab.
Close the cap to secure.
holes for
wires
metal tab
cap
Wire Splice (4)
7. If the Lights are intended to be used
along with the vehicle’s main lights,
connect the lead wire to the headlight
switch positive terminal.
If the Lights are to work independently8.
of the vehicle’s lights, mount the Switch
at a convenient location with the two
Short Screws (3).
Connect the Lead Wire to the middle9.
terminal of the Switch (7).
Connect the Fuse Holder (5) to the top10.
terminal and connect to a 12V power
supply.
Connect the Ground Wire (6) to the11.
bottom terminal of the Switch and the
other end to ground.
This product is intended only to be12.
mounted on the top of a vehicle’s cab.
Installation of these products must13.
comply with DOT regulations and all
applicable State and local laws.
PLEASE READ THE
FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR
HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS DOCUMENT AS
A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR
SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS,
AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.

Page 3SKU 9766-67 For technical questions, please call 1-800-444-3353.
PARTS LIST & DIAGRAM
Part Description Qty.
1 Light 5
2 Long Screws 10
3 Short Screws 2
4 Wire Splice 5
5 Fuse Holder 1
6 Ground Wire (short, black) 1
7 Switch 1
8 Lead Wire (long, red) 1
97966
97967
1
2
3
4
5
6
7
8
Record Serial Number Here:
Note: If product has no serial number,
record month and year of purchase
instead.
Note: Some parts are listed and shown for
illustration purposes only, and are not
available individually as replacement
parts.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes
every effort to assure that its products meet
high quality and durability standards, and
warrants to the original purchaser that this
product is free from defects in materials
and workmanship for the period of 90 days
from the date of purchase. This warranty
does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our
facilities, criminal activity, improper instal-
lation, normal wear and tear, or to lack of
maintenance. We shall in no event be liable
for death, injuries to persons or property,
or for incidental, contingent, special or
consequential damages arising from the use
of our product. Some states do not allow the
exclusion or limitation of incidental or con-
sequential damages, so the above limitation
of exclusion may not apply to you. THIS
WARRANTY IS EXPRESSLY IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty,
the product or part must be returned to us
with transportation charges prepaid. Proof
of purchase date and an explanation of the
complaint must accompany the merchan-
dise. If our inspection veries the defect,
we will either repair or replace the product
at our election or we may elect to refund
the purchase price if we cannot readily and
quickly provide you with a replacement. We
will return repaired products at our expense,
but if we determine there is no defect, or
that the defect resulted from causes not
within the scope of our warranty, then you
must bear the cost of returning the product.
This warranty gives you specic legal
rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009
• Camarillo, CA 93011 • [phone]

Page 4SKU 9766-67 For technical questions, please call 1-800-444-3353.
WIRING DIAGRAM
Lights