Harbor Freight Tools 56658 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 20c
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2019 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly an d se rv ic e may n ot b e in cl uded.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 56658
IMPORTANT SAFETY INFORMATION
1. Do not allow children younger than
age 8 to use this Drone. Children should
not operate without adult supervision.
2. Only fly outdoors during daylight hours in
an area with no obstructions, power lines,
vehicles, animals or people nearby.
3. Do not fly in wet or windy conditions.
4. Keep spectators and pets away. Spectators
should only watch from a safe distance.
5. Position remote control batteries in proper
polarity. Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel-cadmium) batteries.
Do not use swollen or leaking batteries.
6. Do not open the housing or
modify its design. Doing so may cause
damage and/or make it dangerous.
7. Do not use if parts are loose or damaged. If the
toy has been damaged, immediately stop using it.
8. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
9. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
10. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
11. Contains Li-Ion battery. Battery must be
recycled or disposed of properly. Do not open,
crush, heat above 140°F or incinerate.
Lithium Battery Charging Safety
1. Do not leave Battery unattended while charging.
2. Battery charging should be done by adults only.
3. Use the supplied USB charging cable only.
4. Charge on non-flammable surface and
keep away from flammable items.
5. If battery-powered device has been damaged,
immediately stop use, unplug, and safely
move away from flammable materials.
6. Follow instructions for charging battery. DO
NOT charge longer than recommended.
7. Allow a clearance of at least 4″ on
all sides during charging.
Lithium Battery Safety Warnings
LITHIUM BATTERIES STORE
A LARGE AMOUNT OF ENERGY AND
WILL VENT FIRE OR EXPLODE IF MISTREATED:
1. Keep Battery Pack dry.
2. DO NOT DO ANY OF THE FOLLOWING
TO THE BATTERY PACK:
a. Open,
b. Drop,
c. Short-circuit,
d. Puncture,
e. Incinerate, or
f. Expose to temperatures greater than 265°F.
3. Charge Battery Pack only according
to its Charger’s instructions.
4. Inspect Battery Pack before every use;
do not use or charge if damaged.
Personal Safety
1. Operator and spectators must wear ANSI-
approved safety goggles during use.
2. Do not wear loose clothing or jewelry. Keep
hair and clothing, and away from moving
parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
3. Do not use the Drone while tired or
under the influence of drugs, alcohol, or
medications. A moment of interruption
can result in serious personal injury.

Page 3For technical questions, please call 1-888-866-5797.Item 56658
Set Up
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Switch the Remote Control OFF before performing any procedure in this section.
Charging Battery
CAUTION! Do not leave Drone unattended
while charging. Battery charging
should be done by adults only.
1. Make sure Drone and Remote Control are turned OFF.
2. Remove Battery from battery
compartment on back of Drone.
3. Plug Battery cable into the back of the USB Adapter.
USB
Adapter Battery
4. Plug the USB Adapter into a USB power source.
5. While Battery is charging, LED light on USB
Adapter is on. When fully charged, LED light
turns off. Charging takes approximately 1 hour.
6. When charging is complete, disconnect battery
from USB Adapter and power source.
Remote Control
1. Remove the screw securing the Battery Cover
on the back of the Remote Control.
Battery
Cover
2. Remove the Battery Cover and insert three AAA
batteries (sold separately) in the indicated polarity.
3. Replace Battery Cover and tighten screw securely.
CAUTION! Do not install old and new batteries
together. Do not install alkaline, carbon-
zinc or rechargeable batteries together.
Position batteries in proper polarity. Do
not use swollen or leaking batteries.
Specifications
Remote Control
Battery Type 3 – AAA (sold separately)
Drone Battery Type 3.7 V / 380 mAh rechargeable
Lithium-Polymer
Battery Charging Time 65 minutes
Flying Time Approximately 6 minutes
Range Up to 50 meters (about 150 feet)
Operating Frequency 2.4 GHz

Page 4 For technical questions, please call 1-888-866-5797. Item 56658
Controls
Stop
Button
Start
Button
Power
Button
Directional
Switch
FUNCTIONS
UP Press Directional Switch
down & tilt wrist upward
DOWN Press Directional Switch
down & tilt wrist downward
FORWARD Tilt wrist downward
BACKWARD Tilt wrist upward
TURN LEFT Pull Directional Switch
back & tilt wrist to the left
TURN RIGHT Pull Directional Switch
back & tilt wrist to the right
MOVE LEFT Tilt wrist to the left
MOVE RIGHT Tilt wrist to the right
FORWARD FLIP
See page 6
Push Directional Switch
up & tilt wrist downward
BACKFLIP
See page 6
Push Directional Switch
up & tilt wrist upward
LEFT FLIP
See page 6
Push Directional Switch
up & tilt wrist to the left
RIGHT FLIP
See page 6
Push Directional Switch
up & tilt wrist to the right

Page 5For technical questions, please call 1-888-866-5797.Item 56658
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY: Operator below must wear ANSI-approved safety goggles
during use. Keep Drone within 328 feet of Remote Control. If Drone goes out of range, it will stop working
and fall.
WARNING! To prevent serious injury, avoid
sudden movements of controls while flying.
CAUTION! Only fly outdoors during daylight
hours in an area with no obstructions, power
lines, vehicles, animals or people nearby.
Pairing
1. Turn the Drone ON – the red and green LED lights
will flash. Place the Drone on a flat surface.
2. Turn Remote Control ON. Red Indicator
Light will flash twice then stay lit.
3. Drone LED lights will flash rapidly and then stay
lit, indicating the Drone and Remote are paired.
Speed Control
Drone speed is set to normal by default. To change to medium speed, push the Directional
Switch forward once. To change to high speed push the Directional Switch forward again .
To return to normal speed push the Directional Switch forward a third time.

Page 6 For technical questions, please call 1-888-866-5797. Item 56658
Maintenance
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ELECTRICAL SHOCK:
Switch the Remote Control OFF and unplug the Battery from the Drone
before performing any procedure in this section.
1. BEFORE EACH USE, inspect the general
condition of the Drone. Check for:
• loose, misaligned body shell
• bent motor shafts
• cracked or broken rotors
• any other condition that may
affect its safe operation.
2. AFTER USE, use a mild detergent on a clean
cloth to remove any dirt from the Drone.
3. Remove batteries from Remote Control, then store
the Drone and accessories in a dry area away from
direct sunlight and out of the reach of children.
4. Li-Ion BATTERY MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
Do not short, incinerate or open battery
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS DOCUMENT
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.

Page 7For technical questions, please call 1-888-866-5797.Item 56658
Parts List
Part Description Qty
1 Drone 1
2 Blade 2
3 Holder 4
4 USB Adapter 1
5 Remote Control 1
6 Screwdriver 1
7 Screw 4
8 Battery 1
2
1
3
4
5
6
7
8

26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Warning! Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult Customer Service or an experienced radio/TV technician for help.
FCC ID: 2AK3Z-201906
The responsible party in the United States for compliance of the equipment is:
Harbor Freight Tools, 26541 Agoura Road, Calabasas, CA 91302
1-888-866-5797 • http://www.harborfreight.com