Harbor Freight Tools 97004 Installation manual

WIRELESS DOORBELL
Model 97004
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2007 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.

Page 2SKU 97004 For technical questions, please call 1-800-444-3353.
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in
the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
IMPORTANT SAFETY INFORMATION
In this manual, on the labeling, and all other
information provided with this product:
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in minor
or moderate injury.
NOTICE is used to address practices not
related to personal injury.
CAUTION, without the safety alert symbol,
is used to address practices not related to
personal injury.
DANGERDANGER
WARNINGWARNING
CAUTIONCAUTION
NOTICENOTICE
CAUTIONCAUTION

Page 3SKU 97004 For technical questions, please call 1-800-444-3353.
GENERAL SAFETY RULES
WARNING! Read all instructions
Failure to follow all instructions listed below may result in electric shock,
re, and/or serious injury.
SAVE THESE INSTRUCTIONS
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Keep children and bystanders away while installing the Wireless
Doorbell. Distractions can cause you to lose control.
Personal safety
Stay alert, watch what you are doing and use common sense when installing
the Wireless Doorbell.
Use safety equipment. Always wear eye protection. Safety equipment such
as hearing protection used for appropriate conditions will reduce personal
injuries.
Store idle tools out of the reach of children and do not allow persons
unfamiliar with the Wireless Doorbell or these instructions to operate the
Wireless Doorbell.
Maintain the Wireless Doorbell. Check for breakage of parts and any other
condition that may affect the Wireless Doorbell operation. If damaged, have
the Wireless Doorbell repaired before use. Many accidents are caused by
poorly maintained products.
Use the Wireless Doorbell and accessories, in accordance with these
instructions and in the manner intended for this particular type of product.
Use of the Wireless Doorbell for operations different from those intended
could result in a hazardous situation.
SPECIFIC SAFETY RULES
Maintain labels and nameplates on the tool. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
This product is not a toy. Keep it out of reach of children.
Do not get the Wireless Doorbell wet as this will damage the unit.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
1.
a.
b.
2.
a.
b.
c.
d.
e.
1.
2.
3.
4.

Page 4SKU 97004 For technical questions, please call 1-800-444-3353.
SAVE THESE INSTRUCTIONS.
SPECIFICATIONS
Construction
Polystyrene transmitter and receiver,
steel mounting hardware and
thermoplastic anchors
Transmitter Battery (1) VA23A, MS21/MN21, A23S, 12V,
Alkaline (included)
Receiver Battery (2) AA, 1.5V (not included)
Working Distance Up to 200 Feet
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Risk of accidental starting; resulting in serious personal
injury. Turn the Power Switch of the tool to its “OFF”
position and unplug the tool from its electrical outlet before
assembling or making any adjustments to the tool.
Note: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram near the end of this manual.
WARNINGWARNING

Page 5SKU 97004 For technical questions, please call 1-800-444-3353.
Assembly
Installing and Replacing Batteries
Receiver Battery
Compartment
Battery Cover
(3)
Figure 1
You will have to install 2 “AA” Batteries in the Receiver (2). Remove the Battery
Cover (3) located on the back of the Receiver (2)-see Figure 1.
Insert Batteries making certain that the polarity lines up with the polarity
indicated in the Battery Compartment. Replace Battery Cover (3).
Transmitter (1)
Transmitter Battery
Cover (4)
Figure 2
To replace Transmitter Battery, rst remove the Screw (9) holding the Battery
Cover (4) on. Remove the Battery Cover by pulling it up and off.
Replace the Battery in the Battery Compartment so that the battery’s polarity
lines up with that indicated-see Figure 2.
Replace Screw (9) to hold the Battery Cover (4) on.
Mounting
Note that the Transmitter (1) and the Receiver (2) must be mounted within 200
Feet of each other.
1.
2.
3.
4.
5.
1.