Harley Benton ISO-3AC SAG Modular User manual

Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • [email protected] DocID: 523016_08.07.2021
PowerPlant
ISO-3AC SAG Modular
EN
Quick Start Guide
This quick start guide contains important information on the safe operation of the
product. Read and follow the safety advice and instructions given. Retain the quick
start guide for future reference. If you pass the product on to others please include
this quick start guide.
Safety instructions
Intended use
This product is meant to be used as a multiple power supply for eect pedals. Any
other use or use under other operating conditions is considered to be improper
and may result in personal injury or property damage. No liability will be assumed
for damages resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and
are not within reach of babies and young children. Choking hazard! En-
sure that children do not detach any small parts from the product. They
could swallow the pieces and choke!
Where to use the product
Never use the product
• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
• at locations where the unit can become wet
General handling
• To prevent damage, never use force when handling the product.
• Never immerse the product in water. Just wipe it with a clean dry cloth. Do not
use liquid cleaners such as benzene, thinners or ammable cleaning agents.
Features
• Multiple modular power supply unit with SAG option for easy voltage reduction
for fuzz and distortion eects
• 4 isolated, ltered and short-circuit proof outputs eliminate noise and hum
• High current output for modern digital and analogue eects
• LED monitoring at each output
• AC-switchable 100–240V universal input voltage operation
• Modular mains output allows two or more devices (max. 4A) to be connected via
a female-to-male kettle cable (included)
• Compact, robust aluminium housing, can be used on or under pedal boards
• Connections ( ):
- Output 1–2: SAG 4–9V @ max. 500mA (individually isolated)
- Output 3–4: SAG 6–18V @ max. 500 mA (individually isolated)
- Output 5 LINK: 12V @ max. 1000 mA for supplying additional
DC input power supplies
• Dimensions (W×H×D): 130×35×88mm
• Weight: 400g
Scope of delivery
• 5×DC cable 60 cm, 5.5×2.1mm straight-to-angled plug
• 1×power cord with EU plug, 1.2m length
• 1×Kettle cable socket-to-plug
Operating elements
1 Voltage control 14 for the respective output 14
2 Outputs 12, adjustable between 4Vand 9V @500mA
3 Outputs 34, adjustable between 6Vand 18V @500mA
4 Output 5, 12V @ max. 1000 mA
5 Control LED for outputs1–5, lights up green when voltage is applied, turns
o when the output is deactivated due to overload
6 Power cord connection for power supply
7 Mains cable connection to supply voltage to one or more additional devices
(max. 4A)



 



Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • [email protected] DocID: 523016_08.07.2021
PowerPlant
ISO-3AC SAG Modular
EN
For the transport and protective packaging, environmentally friendly ma-
terials have been chosen that can be supplied to normal recycling. Ensure
that plastic bags, packaging, etc. are properly disposed of. Do not just dis-
pose of these materials with your normal household waste, but make sure that they
are collected for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic
Equipment Directive (WEEE) in its currently valid version. Do not dispose of
your old device with your normal household waste. Dispose of this product
through an approved waste disposal rm or through your local waste facil-
ity. Comply with the rules and regulations that apply in your country. If in doubt,
consult your local waste disposal facility.
Using the product
1. To put the device into operation, use the supplied power cord to connect the
INPUT connector on the side of the device to a properly wired power socket,
that provides 100–240V supply voltage .
2. Use suitable voltage supply cables to connect eect pedals or similar devices
which require 4 to 9V supply voltage at a maximum of 500mA to outputs
12. Before doing so, set the associated rotary control to the position of the
required voltage. The maximum output power of 21.6W must not be
exceeded.
Danger of property damage by polarity reversal
Make sure that the polarity of the devices to be connected must be
the same as the polarity of the power supply outputs ( ).
To power a device with polarity-reversed voltage may damage it!
Danger of property damage by overvoltage
Make sure that connected devices are actually suitable for the set
voltage. To power a device with overvoltage may damage it!
3. Use suitable voltage supply cables to connect eect pedals or similar devices
which require 618V supply voltage at a maximum of 500mA to outputs
34. Before doing so, set the associated rotary control to the position of the
required voltage. The maximum output power of 21.6W must not be exceeded.
4. Each operational output is indicated by a green LED. If an output is switched
o due to overload, the LED lights turns o. Then disconnect the pedal in
question from the device. After approx. 2 seconds, the normal voltage supply
is restored here.
5. To supply another device with mains voltage use the supplied Kettle cable to
connect its mains power connection to the OUTPUT connector on the side of
the device.
6. To switch o the device, disconnect the power cord from the mains.