Harman Kardon RCP 4 User manual

RCP 4
SYSTEM REMOTE
OWNER’S MANUAL
(FOR USE WITH CP 45 SYSTEM)
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 1

2
3INTRODUCTION AND FEATURES
4REMOTE CONTROL FUNCTIONS
9BATTERIES
10 PROGRAMMING SOURCES
12 LEARNING INDIVIDUAL KEY CODES
13 ADVANCED FUNCTIONS
13 Punch-Through Programming
13 Macros
14 Resetting the Remote
15 APPENDIX
16 Remote Control Function List
18 Remote Control Product Codes
18 TV
19 VCR
20 CD
20 DVD
21 SAT
21 TAPE
21 CBL
TABLE OF CONTENTS
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 2

3
Please register your product on our Web site at www.harmankardon.com.
Note: You’ll need the product’s serial number. At the same time, you can choose to be notified about our new products
and/or special promotions.
WWW.HARMANKARDON.COM
INTRODUCTION AND FEATURES
Thank you for choosing Harman Kardon®!
Your CP Series system combines the superior performance and practical
flexibility of high-quality separate audio/video components with the
convenience of a complete system in one carton. You will need to
provide a video display or television, but you may also add almost any
source device, ranging from a cassette deck or VCR all the way up
to the latest digital cable or satellite television set-top box (or even
products that may be released in the future).
The single RCP 4 remote replaces the original remotes supplied with
the AVR 245 receiver and DVD 37 DVD player. Although the RCP 4
operates both products, along with a host of other products you may
have added to your system, this manual describes a few differences
from the original remotes.
To obtain the maximum enjoyment from your new home theater
system, we urge you to read this manual, as well as the manuals
included with the system components, and refer back to it as you
become more familiar with its features and their operation. If you
have any questions about this product, its installation or its operation,
please contact your retailer or custom installer, or visit our Web site
at www.harmankardon.com.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 3

4
REMOTE CONTROL FUNCTIONS
The RCP 4 remote is capable of controlling 11 devices, including the
AVR 245 and the DVD 37 included in the CP 45 system. During the
installation process, you may program the codes for each of your source
components into the remote. Each time you wish to use the codes for
any component, first press that component’s selector. This changes the
button functions to the appropriate codes for that product.
NOTE: Several of the Input Selectors are shared between two
devices. The selector button will light in red when the remote is in
the device mode printed on the button, and it will light in green for
the device mode printed above the button. To switch between the
two device modes, press the selector twice quickly in succession.
The selector will remain in the last-selected mode until the next
time you press it twice quickly.
For example, the first time you press the DVD Button, the button
will light in red, indicating that the remote is in DVD mode. If you
press another selector, such as the VID3 Selector, and then press
the DVD Button again, the DVD Button will remain red, indicating
the remote is still in DVD mode. Now press the DVD Button twice
quickly. At the first press the Button will light in red, indicating that
the remote is in DVD mode. On the second press the button will
turn green, indicating that the remote is now in CD mode. If you
press a different selector and return to the DVD/CD Selector, you
will observe that the remote is still in CD mode.
Each Input Selector has been preprogrammed to control certain types
of components, with only the codes specific to each brand and model
changing, depending on which product code is programmed. The
device types programmed into each selector (except HDMI 1 and 2)
may not be changed.
DVD: Controls DVD players and recorders. The DVD Button functions
are labeled in blue on the remote.
CD: Controls CD players and recorders.
Tape: Controls cassette decks.
The Bridge/DMP: Controls an iPod®docked in The Bridge.
Video 1: Controls VCRs,TiVo®and DVRs.
Video 2: Controls cable and satellite television set-top boxes.
Video 3: Controls televisions and other video displays.
Video 4: Controls a TV connected to the front-panel inputs.
HDMI 1 and 2: Each code set controls a source device (such as
a DVD player) connected to one of these two inputs.
XM: Controls the AVR functions for XM Satellite Radio.
For example, if you have inserted a disc in your CD player and you
would like to skip ahead three tracks, but you then find that the volume
is too loud, you would follow this procedure:
1. Press the CD Input Selector to switch to the codes that control your
CD player. If the remote is in DVD mode, press the selector twice quickly
to switch to CD mode, indicated by the selector turning green.
2. Press the Play Button (in the Transport Controls section) if the disc
is not already playing.
3. Press the Skip Up Button three times to advance three tracks.
4. Press the AVR Button so that you can access the volume controls.
5. Press the Volume Down Button until the volume level is satisfactory.
Any given button may have different functions, depending on which
component is being controlled. The buttons are labeled with some of
these functions, with the receiver’s functions shown in white or gray, and
the DVD player’s functions shown in blue. For example, the Sleep and
DSP Surround Buttons are labeled for use as Channel Up/Down Buttons
when controlling a television or cable box. See Table A1 in the Appendix
for listings of the different functions for each type of component.
NOTE: Although we have described the applicable DVD functions
in this section, we strongly recommend that you review the
DVD 37 manual for more information about using these functions.
IR Transmitter Lens: As buttons are pressed on the remote,
infrared codes are emitted through this lens. Make sure it is pointing
toward the component being operated.
Power On Button: Press this button to turn on the AVR or another
device. The Master Power Switch on the AVR 245’s front panel must
be switched on first.
Mute Button: Press this button to mute the AVR 245’s speaker and
headphones outputs temporarily. To turn off muting, press this button
or adjust the volume. Muting is also canceled when the receiver is
turned off.
Program Indicator: This LED lights up or flashes in one of three colors
as the remote is programmed with codes.
Power Off Button: Press this button to turn off the AVR 245 or
another device.
AVR Selector: Press this button to switch the remote to the codes
that operate the receiver.
Input Selectors: Press one of these buttons to select a source
device, which is a component where a playback signal originates (e.g.,
DVD, CD, cable TV, satellite or HDTV tuner). This will also turn on the
receiver (if it is not already on) and switch the remote’s mode to operate
the source device.
AM/FM Button: Press this button to select the tuner as the source,
or to switch between the AM and FM bands.
6-/8-Channel Input Selector: Press this button to select the
6-/8-Channel Inputs as the audio source. The receiver will use the video
input and remote control codes for the last-selected video source.
XM Radio Button: Press this button to select XM Satellite Radio as
the source. You will need to have purchased and activated an XM antenna
module, and you will also need to subscribe to the XM Radio service.
Visit www.xmradio.com for more information.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 4

5
IR Transmitter Lens
Program Indicator
Power On
AVR Selector
AM/FM
XM Radio
Test Tone
Sleep/Audio Select
DSP Surround/Title
On-Screen Display/Disc Info
Channel Level/Disc Menu
Digital Input Select/
Drawer Open/Close
Tuning Mode/Zoom
Direct Station Entry/Angle
Tuning
Dolby
®
Surround
Tone Mode/DVD Scan Type
DTS
®
Surround/A-B Repeat
Night Mode/Subtitle
Track Skip
Transport Controls
Power Off
Mute
Input Selectors
6-/8-Channel Input Selector
Learn
TV/Video/Video Off
Volume Controls
Multiroom/HD Mode
Speaker Setup/DVD Setup
Set
Numeric Keys
Delay/DVD Status
Memory/Playlist
Clear
Preset Stations Selectors
Disc Skip
Macros
DTS Neo:6
®
Surround
Stereo Modes/Repeat
Dim
Backlight
Logic 7
®
Surround/Random
Record
Navigation
®
NOTE: To make it easier to follow the instruc-
tions throughout the manual that refer to this
illustration, a copy of this page may be down-
loaded from the Product Support section at
www.harmankardon.com.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 5

6
Learn Button: The RCP 4 remote is capable of “learning” individual
IR codes from the original remote that came with your TV or a device
that is connected to any of the source inputs. See the Programming
Sources section for instructions on learning remote codes.
Test Tone: Press this button to activate the test tone for manual
output-level calibration.
TV/Video/Video Off: This button has no effect on the receiver,
but is used to switch video inputs on some video source components.
When the DVD player has been selected (by pressing the DVD Input
Selector), pressing this button disables the DVD 37’s video output to
avoid “burning in” menus or still images on sensitive video displays. This
feature is particularly useful when listening to CDs or other audio-only
presentations.
Sleep/Audio Select Button: Press this button to activate the sleep
timer, which shuts off the receiver after a programmed period of up to
90 minutes.
When the DVD player has been selected, this button may be used to
select another audio format or language, if one is available on the disc.
Volume Controls: Press these buttons to raise or lower the volume,
which will be shown in decibels (dB) in the Message Display.
DSP Surround/Title: Press this button to select a DSP Surround
mode (Hall 1, Hall 2, Theater).
When the DVD player has been selected, this button serves the Title
function. When a DVD is playing, press this button to go back to the
main title menu for the disc. If you are playing a DVD-Audio disc that
contains formats the DVD 37 is capable of playing, such as linear PCM
or Dolby®Digital 5.1, pressing this button may enable you to switch
playback from one audio format to another.
On-Screen Display (OSD)/Disc Info: Press this button to
activate the AVR 245’s on-screen menu system.
When the DVD player has been selected, this button serves the Disc
Info function. Press it once to access the Player Information menu for
information on the current disc and the playback mode settings. This
function is different from the Disc Menu and DVD Setup functions.
Multiroom/HD Mode:Press this button to control the multiroom
system. Three settings are available: MULTI ON/OFF, which is used to
turn the multiroom system on or off; MULTI LEVEL, which adjusts the
volume of the remote zone; and MULTI INPUT, which is used to select
the source input for the remote zone. See Multiroom Operation in
the Advanced Functions section of the AVR 245 manual for more
information on using the multiroom system.
When the DVD player has been selected, this button serves the HD
Mode function, which is available when the DVD 37’s HDMI™output
is used. Pressing this button enables you to select a lower resolution
than the maximum your video display is capable of handling, as
determined by the “handshake” procedure between the DVD 37 and
AVR 245 and your video display.See the DVD 37 owner’s manual
for more information on HDMI and the HD Mode Selector.
Channel Level/Disc Menu: Press this button to set the output
levels for each channel so that all speakers sound equally loud at the
listening position. Usually this is done while playing an audio selection, such
as a favorite CD, after you have calibrated the levels using EzSet+®
.
When the DVD player has been selected, this button serves the Disc Menu
function. While a disc is playing, press this button to view the disc’s menu.
This function is different from the Disc Info and DVD Setup functions.
Speaker Setup/DVD Setup: Press this button to configure
speaker sizes, that is, the frequency-range capability of each speaker.
Usually this is done using the on-screen menu system, as described
in the Initial Setup section of the AVR 245 owner’s guide.
When the DVD player has been selected, this button serves the DVD
Setup function. Press it to use the DVD 37’s on-screen menu system to
adjust the player’s configuration settings. This function is different from
the Disc Info and Disc Menu functions.
Navigation and Set Buttons: These buttons are used together
to make selections within the AVR 245’s or DVD 37’s on-screen menu
system, or when accessing the AVR functions of the four buttons
surrounding this area of the remote – Channel Level, Speaker Setup,
Digital Input or Delay.
Digital Input Select/Drawer Open/Close: Press this button to
select the specific digital audio input (or analog audio input) you used
for the current source.
When the DVD player has been selected, this button is used to open
or close the disc drawer.
Delay/DVD Status: Press this button to set delay times that
compensate for placing the speakers at different distances from the
listening position, or to resolve a “lip sync” issue that may be caused
by digital video processing. This may also be done using the on-screen
menu system, as described in the Initial Setup section of the AVR 245
owner’s guide.
When the DVD player has been selected, this button serves the DVD
Status function. Press it while a DVD is playing to view the on-screen
Status Bar, which will display the current title and chapter, the Play Mode
icon and the elapsed time, in addition to a “temperature bar” display of
the time elapsed. The Status Bar may be navigated as described in the
DVD 37 manual.
Numeric Keys: Use these buttons to enter radio station frequencies
or to select station presets.When the AM or FM band is in use,press
the Direct Button before entering the station frequency.
When listening to XM Radio, you may enter channel numbers without
first pressing the Direct Button; however, to access the preset stations,
you will need to use the Preset Stations Selectors. To access another
bank of XM presets, press the Set Button repeatedly until PRESET
SEARCH appears, then use the ⁄/¤Buttons to select the letter
of the desired bank.
Tuning Mode/Zoom: When listening to AM or FM radio, this button
toggles between Manual (one frequency step at a time) and Automatic
6
REMOTE CONTROL FUNCTIONS
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 6

(seeks frequencies with acceptable signal strength) Tuning modes. It also
toggles between Stereo and Mono modes when an FM station is tuned.
When listening to XM Radio, press the Tuning Mode Button once to view
the category name of the current channel. Additional presses will display
the artist, song title and channel name.
When the DVD player has been selected, this button performs the Zoom
function. Press it to zoom in on a DVD, VCD or JPEG image. The image
may be enlarged by a factor of x2, x3, x4 or x5. Once the on-screen
indication of the zoom ratio disappears from the screen, you may use
the Navigation Buttons to explore the picture.
Memory/Playlist: After you have tuned a particular radio station, press
this button, then a Numeric Key, to save that station as a radio preset.
For XM Radio, the procedure for saving a preset is a little different. To
save the current channel in one of the 40 available preset locations,
press the Set Button repeatedly until PRESET SEARCH appears. Use
the ⁄/¤Buttons to select a letter (A through E) representing one of
the five banks of preset memory slots. Then press the Memory Button,
followed by a Numeric Key (1 through 8) for the precise preset memory
location you wish to save the channel in.
When the DVD player has been selected, this button performs the
Playlist function, which enables you to change the order in which tracks
or chapters are played.
Tuning: Press these buttons to tune a radio station or XM Radio
channel. For the AM and FM bands, and depending on whether the
tuning mode has been set to Manual or Automatic, each press will either
change one frequency step at a time, or seek the next frequency with
acceptable signal strength.
Direct Station Entry/Angle: Press this button before using
the Numeric Keys to directly enter a radio station frequency (AM or
FM bands only).
When the DVD player has been selected, this button is used for the
Angle function. Press it during passages on a DVD where the director
has programmed multiple camera angles to view the alternate perspec-
tives. When a JPEG file is on-screen, each press of this button rotates
the image by 90 degrees clockwise.
Clear: Press this Button to clear a radio station frequency you have
started to enter.
When the DVD player has been selected, this button may be used
to clear any on-screen displays from view. In addition, press and hold
it for five seconds to reset all user settings on the DVD 37 to their
factory defaults.
Preset Stations Selector: Press these buttons to select a preset
radio station.
For XM Radio, first press the Set Button repeatedly until PRESET SEARCH
appears, and then use the ⁄/¤Buttons to select the letter of the
desired bank of presets.
Tone Mode/DVD Scan Type: Press this button to access the tone
controls (bass and treble). Use the Navigation Buttons to make your
selections.
When the DVD player has been selected, this button adjusts the Video
Scan Type setting for the component video outputs. Each press toggles
between progressive and interlaced scanning. This button is useful if you
inadvertently set the scan type to progressive when your video display
or television is not capable of displaying progressively scanned video.
Although your video display may be distorted, you may restore inter-
laced scanning by pressing this button.
Disc Skip: This button has no effect on the AVR 245 or the DVD 37,
but is used with some optical disc changers to skip to the next disc.
Macros: These buttons may be programmed to execute long com-
mand sequences with a single button press. They are useful for pro-
gramming the command to turn on or off all of your components, or for
accessing specialized functions for a different component than the one
you are currently operating.
Dolby®Surround Mode Selector: The first press of this button
will select the last-used Dolby Surround mode, and each additional
press will cycle through the variants that are currently available. Not
all modes are available with all sources; see the AVR 245 manual for
more information.
DTS®Surround Mode Selector/A-B Repeat: The first press of
this button will select the last-used DTS Digital mode if DTS processing is
available,and each additional press will toggle between the 2.0, 5.1 and
DTS-ES®variants.See the AVR 245 manual for more information.
When the DVD player has been selected, this button serves the A-B
Repeat function. The first press while a disc is playing selects the begin-
ning of the passage you wish to repeat, and the second press selects
the end of the passage.The selected passage will play continuously until
the A-B Button is pressed a third time, or play is stopped.
DTS Neo:6®Surround Mode Selector: The first press of this
button will select the last-used DTS Neo:6 Surround mode if it is avail-
able, and each additional press will cycle through the variants that are
currently available. See the AVR 245 manual for more information.
Logic 7®Surround Mode Selector/Random: The first press
of this button will select the last-used Logic 7 Surround mode if it is
available, and each additional press will cycle through the Cinema, Music
and Enhance modes.See the AVR 245 manual for more information.
When the DVD player has been selected, this button serves the Random
function. When a CD is playing and no playlist is active, each press of
this button turns random track selection on or off.
Night Mode/Subtitle: Press this button to activate Night mode
with specially encoded Dolby Digital discs or broadcasts. Night mode
compresses the audio so that louder passages are reduced in volume
to avoid disturbing others, while dialogue remains intelligible.
When the DVD player has been selected, this button performs the Subtitle
function. Press it to select a subtitle language or to turn subtitles off.
77
REMOTE CONTROL FUNCTIONS
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 7

8
REMOTE CONTROL FUNCTIONS
NOTE: Due to the variations in how DVD discs are authored, the
subtitle languages displayed by the DVD 37 may not accurately
reflect the actual languages available on the disc. It is recom-
mended that subtitles be selected using the disc’s menu.
Stereo Modes/Repeat: The first press of this button will select
the last-used Stereo mode, which may be Surround Off or Two-Channel
Processing. Each additional press will toggle between Surround Off,
5-Channel Stereo and 7-Channel Stereo. When an analog audio source
is in use and the AVR 245’s Tone Mode control has been set to Out,
you may also select Analog Bypass mode, which passes the analog
input signal to the volume control, bypassing digital signal processing.
See the AVR 245 manual for more information.
When the DVD player has been selected, each press of this button
cycles through the available Repeat modes, excluding A-B Repeat.
Track Skip: These buttons have no effect on the receiver, but are
used with the DVD 37 and many other source components to change
tracks or chapters.
Dim: Press this button to partially or fully dim the AVR 245’s front-
panel display.
Transport Controls: These buttons have no effect on the receiver
but are used to control the DVD 37 and many other source compo-
nents. By default, when the remote is operating the receiver, these
buttons will control the DVD 37.
Record: This button has no function on the AVR 245 or DVD 37.
It is used with many audio and video recorders.
Backlight: Press this button to illuminate the buttons on the remote.
Press it again to turn the backlight off, or wait for five seconds after the
last button press for the light to turn off on its own.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 8

9
BATTERIES
The RCP 4 remote control uses three AAA batteries, which are included.
To remove the battery cover located on the back of the remote, firmly
press the ridged depression and slide the cover toward the top of
the remote.
Insert the batteries as shown in Figure 1, making sure to observe
the correct polarity.
Figure 1 – Remote Battery Compartment
When using the remote, remember to point the lens toward the front
panel of the AVR 245 or DVD 37. Make sure no objects, such as
furniture, are blocking the remote’s path. Bright lights, fluorescent lights
and plasma video displays may interfere with the remote’s functioning.
The remote has a range of about 20 feet, depending on the lighting
conditions. It may be used at an angle of up to 30 degrees to either
side of the component.
If the remote seems to operate intermittently, or if pressing a button
on the remote does not cause the AVR Selector or one of the Input
Selectors to light up, then make sure the batteries have been inserted
correctly, or replace all three batteries with fresh ones.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 9

10
PROGRAMMING SOURCES
10
Programming Sources
The RCP 4 remote is capable of controlling not only the receiver and
DVD player included in your CP system, but it may also be programmed
to control many brands and models of VCRs, CD players, cable boxes,
satellite receivers, cassette decks and TVs, as well as an iPod (not
included) docked in Harman Kardon’s optional The Bridge.
It may help to think of the remote as a book with pages. Each page
represents the button functions for a different device. In order to access
the functions for a particular device, you first need to turn to that page,
that is, switch the remote to that device mode. This is done by pressing
the AVR Button to access the codes that control the receiver, or the
Input Selectors to access the codes for the devices programmed into
the remote.
You may have noticed that three of the Input Selectors look different
from the others (see Figure 2). For the DVD/CD, TAPE/The Bridge and
HDMI 1/HDMI 2 Selectors, there is a primary source, whose name is
printed on the button, and a secondary source, whose name is printed
above the button.
When the remote is in the device mode for the primary source (e.g.,
DVD) pressing the device selector will cause it to light in red. When the
remote is in the secondary source’s device mode, the selector will light
in green when pressed.
To switch between the primary and secondary device modes, press the
selector twice quickly in succession. The selector will retain this selection
until the next time you toggle between the primary and secondary
device modes. That is, if you press the DVD/CD Selector twice quickly
so that the CD source is activated, then press another source selector,
such as Video 1, the next time you press the DVD/CD Selector, the
remote will return to the CD device mode.
The RCP 4 remote is factory-programmed to control the AVR 245, the
DVD 37 and an iPod docked in The Bridge. If you have other source
devices in your system, such as a VCR, or a cable or satellite television
set-top box, follow these steps to program the correct codes into the
remote:
1. Using the codes in Tables A2–A9 of the Appendix, look up the
product type (e.g., cable TV box) and the brand name of your source.
The number(s) listed are potential candidates for the correct code set
for your particular device.
2. Turn on your source device.
3. This step places the remote in Program mode and varies slightly,
depending on which Input Selector is being programmed. Refer to
Figure 2.
a) DVD, Tape, Video 1, Video 2, Video 3 and Video 4 Sources:
Press and hold the Input Selector until the Program Indicator LED
starts to flash, then release it. Follow the directions in Step 4.
b) CD Source: Press the DVD/CD Input Selector twice quickly so
that it turns green. Follow the directions in Step 4.
c) HDMI 1 Source: Press and hold the Input Selector until the
Program Indicator flashes, then release it. Next press the Input
Selector that corresponds to the device type you want to program
into the HDMI 1 mode, i.e., DVD, VCR or CBL/SAT. Then follow
the directions in Step 4.
d) HDMI 2 Source: Press and release the Input Selector once,
quickly press the Input Selector again so that it turns green, then
release it. Now press and hold the Input Selector until the Program
Indicator flashes, then release it. Next press the Input Selector
that corresponds to the device type you want to program into
the HDMI 2 mode, i.e., DVD, VCR or CBL/SAT. Then follow the
directions in Step 4.
Figure 2 – Input Selectors
4. Enter a code from Step 1 above.
a) If the device turns off, then press the Input Selector again to accept
the code; the selector will flash. The remote will exit the Program mode.
b) If the device does not turn off, try entering another code. If you
run out of codes, you may search through all of the codes in the
remote’s library for that product type by pressing the ⁄or ¤
Button repeatedly until the device turns off. When the device turns
off, enter the code by pressing the Input Selector, which will flash.
The remote then exits Program mode.
NOTE: When you enter a valid three-digit code, the Program
Indicator LED will change color to green. However, entering an
invalid code changes the color of the LED to red.
5. Once you have accepted a code, it’s a good idea to try using some
other functions to control the device. Sometimes manufacturers
use the same power code for several different models, while other
codes will vary. You may wish to repeat this process until you’ve
programmed a satisfactory code set that operates most of the
functions you frequently use.
6. You may find out which code number you have programmed by
pressing and holding the Input Selector to enter Program mode. Then
press the Set Button, and the LED will flash in the code sequence.
One flash represents “1”, two flashes for “2” and so forth. A series of
many fast flashes represents “0”. Record the codes programmed for
each device in Table 1.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 10

1111
PROGRAMMING SOURCES
Table 1 – Remote Control Codes
*Do not reprogram the DVD Source selector unless you are replacing
the DVD player included in the CP 45 system with another product.
7. After you have programmed a code set to operate a device, test
the functions to see which ones may be missing or not operating
correctly. You may “learn” individual key codes if you have the
device’s original remote control by following the procedure below. If
you no longer have the device’s original remote, you may still connect
it to the AVR 245. You may wish to consider purchasing Harman
Kardon’s optional TC 30 activity-based remote, which is programmed
by accessing a large database of product codes on the Internet.
Most of the button labels on the remote describe the button’s function
when used to control the AVR 245 (white or gray labels) or DVD 37
(blue labels). However, the button may perform a very different function
when used to control another device. Refer to the Remote Control
Function List, Table A1 in the Appendix, for a list of each button’s
functions with the various product types.
If you wish, you may program macros,which are preprogrammed
code sequences that execute many code commands with a single
button press.You may also program “punch-through” codes, which
allow the remote to operate the volume,channel or transport controls
of another device without having to switch the remote’s device mode.
See page 13 for instructions on these advanced programming
functions.
NOTE: The RCP 4 remote is preprogrammed to operate the
transport controls of the DVD 37 when the AVR or VID2 or VID3
device
is selected. You may change this punch-through program-
ming at any time, as explained in the Advanced Functions section.
Source Input Product Type Remote Control Code
(circle one)
Video 1 VCR, PVR
Video 2 Cable, Satellite
Video 3 TV
Video 4 TV
HDMI 1 DVD, VCR, Cable, Satellite
HDMI 2 DVD, VCR, Cable, Satellite
DVD*DVD
CD CD, CD-R
Tape Cassette
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 11

The following keys on the RCP 4 remote may be programmed with
individual IR codes that are “learned” from another remote control:
Power On/Off, Mute, Sleep and DSP Surround/Title (Channel Up/Down),
Volume Controls, Channel Level/Disc Menu, Speaker/DVD Setup, Digital
Input/Drawer Open/Close, Delay/DVD Status, ‹›⁄¤ Navigation, Set,
Numeric Keys, Track Skip Up/Down and Transport Controls – a total of
34 buttons.
Follow these steps to learn individual key codes:
1. Place the RCP 4 and the device’s original remote so that their IR
transmitters face each other end to end, separated by about one
inch (see Figure 3). The RCP 4 remote’s transmitter also serves as
an IR receiver during the learning process.
Figure 3 – RCP 4 and Original Remote Head-to-Head
2. Make sure the RCP 4 is in the device mode you want to learn
the new key code for by pressing the Input Selector, which should
light in red, or green if it is a secondary source on a dual-source
selector. If necessary, press a dual-source selector twice to select
between the primary and secondary sources. Place the RCP 4
remote in Learning mode by pressing and holding the Learn
Button until the Program Indicator flashes amber, then releasing
(see Figure 4).
Figure 4 – Learning Remote Commands
3. Press and hold the button on the RCP 4 remote you wish to program
with the new code until the Program Indicator remains steadily lit
amber,then release it.
4. Press and hold the button on the device’s original remote whose
code you wish to “learn” until the RCP 4’s Program Indicator flashes
green, then release it.
5. You may program additional buttons by repeating Steps 3 and 4.
To exit Learning mode, press the Learn Button once. If you prefer,
you may wait for the remote to “time out” and exit Learning mode
on its own, but this will take about 30 seconds.
If you make a mistake while learning a code, you may either learn
a new code over the old code, or you may erase the learned code,
which returns the button to the code in the original code set that you
programmed into the Input Selector. To erase a single learned code:
1. Make sure the RCP 4 is in the device mode containing the learned
code you wish to erase by pressing the Input Selector, which should
light in red, or green if the secondary source on a dual-source
selector is active.
2. Press and hold the Learn Button until the Input Selector lights and
the Program Indicator flashes amber, then release.
3. Press the Input Selector again and release.
4. Enter the code “777” by pressing the “7” Numeric Key three times.
The Input Selector should flash each time.
5. Press the button whose learned code you wish to erase and release.
The Program Indicator will flash green to confirm the erasure.
6. Repeat Step 5 for any other buttons whose learned codes you wish
to erase.
7. Press the Learn Button to exit Learning mode, or wait about 30
seconds for Learning mode to time out.
To erase all of the learned codes for a device mode:
1. Make sure the RCP 4 is in the device mode containing the learned
code you wish to erase by pressing the Input Selector, which should
light in red, or green if the secondary source on a dual-source
selector is active.
2. Press and hold the Learn Button until the Input Selector lights and
the Program Indicator flashes amber, then release.
3. Press the Input Selector again and release.
4. Enter the code “888” by pressing the “8” Numeric Key three times.
The Input Selector should flash each time. The Program Indicator
will flash green to confirm the erasure.
To erase all of the learned codes on the remote for all device modes,
but without erasing other user settings such as product code sets or
punch-through programming,follow these steps:
1. Press and hold the Learn Button until the Input Selector lights in
red and the Program Indicator flashes amber, then release.
2. Press any Input Selector and release.
3. Enter the code “999” by pressing the “9” Numeric Key three times.
The Input Selector should flash each time. The Program Indicator will
go dark, and the Input Selector you pressed in Step 2 will remain lit for
about 10 seconds.Then the Program Indicator will flash green to con-
firm the erasure,and the remote will automatically exit Learning mode.
12
LEARNING INDIVIDUAL KEY CODES
12
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 12

13
ADVANCED FUNCTIONS
The RCP 4 remote control not only operates the AVR 245 and DVD 37,
but it also serves as a universal remote that may be programmed to
operate many of your other home theater components. The punch-
through and macro features add even more flexibility and versatility.
Punch-Through Programming
The RCP 4 remote allows you to select one component for the remote
to operate, while simultaneously setting certain groups of controls to
operate another component. For example, while using the AVR to control
surround modes and other audio functions, you may wish to operate the
transport controls of your DVD player. Or while using the remote to con-
trol video functions on your TV, you may wish to use your cable box to
change channels and the AVR to control the volume.
All of this is possible using punch-through programming.
NOTE: It is not necessary to program the remote to control
your DVD player’s transport controls while the AVR or a device
connected to the VID2 or VID3 inputs is in use, as the remote
is preprogrammed at the factory with this function.
To program punch-through control while operating any device:
1. Press and hold the Input Selector (or AVR Selector) for the main
device the remote will be operating until the Input Selector lights,
the Program Indicator LED flashes and the remote enters Program
mode.
2. Select the type of punch-through programming:
a) To program volume control punch-through, press the Volume
Up Button.
b) To program channel control punch-through, press the Volume
Down Button.
NOTE: Do not program channel-control punch-through for the
AVR. Doing so will override the Sleep command, which is not
accessible in any other way, and the DSP Surround Mode
Selector. If you have inadvertently done so, repeat Steps 1
through 3, but press the AVR Selector in both Steps 1 and 3.
c) To program Transport Control punch-through, press the Play Button.
3. Press the Input Selector (or AVR Selector) for the device whose
volume, channel or transport controls you would like to be active
while operating the device you selected in the first step. The LED
will flash green to confirm the programming.
For example, if you wish to watch your TV (programmed into the Video 3
button) while changing channels using your cable box (Video 2), you
would first press the Video 3 Button until the LED flashed. You would
then press the Play Button, followed by the Video 2 Button.
To undo punch-through programming, follow the same steps as above,
but press the same Input (or AVR) Selector in Steps 1 and 3.
NOTE: As mentioned earlier, the AVR, VID2 and VID3 devices
are factory-programmed with transport-control punch-through
to operate the DVD player. You may reprogram these selectors
following the instructions in Steps 1 through 3 to operate another
device, such as a CD player.
If you wish to reprogram these selectors to have no transport-
control punch-through, the process is slightly different. Each of
these three selectors has no native transport-control commands.
Therefore, when reprogramming them to eliminate transport-
control punch-through, in Step 3 you must select one of these
three selectors, but not the same one you are reprogramming.
For example, to remove transport-control punch-through from
the VID2 device, follow the instructions in Steps 1 through 3,
but press either the AVR or VID3 Button in Step 3.
Macros
Macros are used to program sequences of up to 19 commands
that are executed with a single button press. Macros are well-suited
for Power On and Off commands, to send out a favorite multidigit
channel number with one button press, or to have the ability to send
out a code sequence to control another device while the remote is
operating one device but with more flexibility than the built-in punch-
through controls.
Some commands may not be programmed into macros: Mute, Dim,
Channel Up/Down and any of the Surround Mode commands.
NOTE: Use caution when programming complicated macros. It
isn’t possible to program a pause or delay before sending com-
mands after powering on, and the component may not be ready
to respond to commands instantaneously after powering on.
To program, or “record,” a macro, follow these steps:
1. Simultaneously press one of the four Macro Buttons or the Power On
Button and the Mute Button at the same time to enter Program mode.
2. Press the Input (or AVR) Selector for each device before you enter
commands to be transmitted to that device. This step counts as one
of the 19 commands allowed for each macro.
NOTE: Even if you previously switched one of the dual-source
Input Selectors (DVD/CD,TAPE/THE BRIDGE, HDMI 1/HDMI 2)
to the primary or secondary source prior to programming the
macro, the remote always requires you to press any of these
selectors once to program the macro to select the primary
source and twice for the secondary source.
3. For the Power On command, do not press the Power On Button.
Press the Mute Button instead.
4. Press the Power Off Button to program the Power Off command.
5. Press the Sleep Button to end the programming process.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 13

14
It isn’t possible to “edit” a command within a macro. However, you
may erase the macro as follows:
1. Simultaneously press and hold the Mute Button and the Macro
Button containing the macro until the Program LED flashes.
2. Press the Surround Button to erase the macro.
Here are two macros that you may find useful when listening to an iPod
docked in The Bridge:
The purpose of the first macro is to access the DMP SETTING menu
while listening to The Bridge with one button press:
1. Simultaneously press and hold the M1(or other unused) Macro
Button and the Mute Button until the Program LED flashes.
2. Press the AVR Button (first command switches the remote to AVR
mode).
3. Press the OSD Button (second command activates the on-screen
menu system).
4. Press the Set Button (third command selects the INPUT SETUP
menu; this macro assumes the current source is The Bridge).
5. Press the ¤Button three times (fourth, fifth and sixth commands
navigate to the GO TO DMP SETTING line).
6. Press the Set Button again (seventh command selects the DMP
SETTING menu).
7. Press the Sleep Button to end the programming process. You have
now programmed the first macro, which will display the DMP SET-
TING menu after you have selected The Bridge as your source input.
After you have made your selections in the DMP SETTING menu, such
as turning on Repeat Playback or Shuffle mode, the second macro
enables you to exit the on-screen menu system and return the remote
to The Bridge mode, again with just one button press.
1. Simultaneously press and hold the M2 (or other unused) Macro
Button and the Mute Button until the Program LED flashes.
2. Press the OSD Button (first command exits the on-screen menu system;
this macro assumes that you have not let the OSD time out).
3. Press the Tape/The Bridge Input Selector twice (second and third
commands switch the selector to The Bridge mode and select
The Bridge as the source). This step is required even if you already
switched the selector’s mode before programming the macro.
4. Press the Sleep Button to end the programming process. You have
now programmed the second macro,which may be used after run-
ning the first macro to exit the OSD system quickly and return the
remote’s operation to The Bridge.
Resetting the Remote
To reset the remote to its factory defaults, simultaneously press and
hold any Input Selector and the “0” Numeric Key. When the LED flashes
amber, enter the code “333”. When the green LED goes out, the remote
will have been fully reset.
ADVANCED FUNCTIONS
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 14

15
13
6
9
13
16 19
22
25
31
34
2
5
8
12 15
18
21
24
27 29
33
47
10 11
14
17
20 23
26
28
30
32
35
37
36
38 40
39
41 42 44
43
45 46 47 48
49 50 5251
54 55 56
58
57 59
60 61
53
62
64 65
66 68
67
69 70 71
63
72
®
Refer to the numbered buttons in this drawing when using the Function List.
Figure 5 – Remote Control Function List Reference
APPENDIX
RCP4 remote OM.qxd 11/21/06 4:12 PM Page 15

16
APPENDIX
Table A1 – Remote Control Function List
No. Button Name AVR Function DVD CD/CD-R Tape VCR (VID1) TiVo (VID1) CBL (VID2) SAT (VID2) TV (VID3/VID4) (DMP) XM HDMI 1/2
1 Power On Power On Power On Power On Power On Power On/Off Power On Power On Power On Power On
2 Power Off Power Off Power Off Power Off Power Off TV Power Power Off Power Off Power Off Power Off
3Mute Mute Mute (AVR) Mute (AVR) Mute (AVR) Mute Mute Mute Mute Mute Mute
4 AVR AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select
5 DVD/CD DVD Input Select DVD Select DVD Select DVD Select DVD Select DVD Select DVD Select DVD Select DVD Select DVD Select DVD Select DVD Input Select
CD Input Select CD Select CD Select CD Select CD Select CD Select CD Select CD Select CD Select CD Select CD Select CD Input Select
6 T ape/ Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select
The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Select The Bridge (DMP) Selectt
7 HDMI 1/HDMI 2 HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select HDMI 1 Select
HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select HDMI 2 Select
8 VID 1 (VCR) Video 1 Select VCR Select VCR Select VCR Select VCR Select VCR Select VCR Select VCR Select VCR Select VCR Select VCR Select VCR Select
9 VID 2 (CBL/SAT) Video 2 Select CBL/SAT Select CBL/SAT Select CBL/SAT Select CBL/SAT Select CBL/SAT Select CBL Select SAT Select CBL/SAT Select CBL/SAT Select CBL/SAT Select CBL/SAT Select
10 VID 3 (TV) Video 3 Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select
11 VID 4 Video 4 Select Video 4 Select Video 4 Select Video 4 Select Video 4 Select Video 4 Select Video 4 Select Video 4 Select Video 4 Select Video 4 Select Video 4 Select Video 4 Select
12 XM XM Select XM Select XM Select XM Select XM Select XM Select XM Select XM Select XM Select XM Select XM Select XM Select
13 AM/FM Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select
14 6/8CH 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select 6/8 Ch. Input Select
15 Learn Learn Learn Learn Learn Learn Learn Learn Learn Learn Learn Learn Learn
16 Sleep/Audio Sleep Audio Channel + Channel + Channel + Channel + Channel + Channel +
17 Test Tone Test Tone
18 T/V/V.Off V. OFF or TV/DVD
*
Input Select TV/VCR TV Input TV/CBL TV/SAT TV/VCR TV/Video
19 Vol Up Volume Up
*
Volume Up Volume Up Volume Up Volume Up
20 Surr/Title DSP Surround Mode Select Title or Disc Menu
*
CDR Select Channel – Channel – Channel – Channel – Channel – Channel –
21 OSD/Info OSD Disc Info Program OSD Live TV OSD OSD OSD OSD
22 M-Room/HD Multiroom HD Mode
23 Vol Down Volume Down Volume Down Volume Down Volume Down Volume Down Volume Down
24 CH./Disc Menu Channel Trim Disc Menu or Title
*
Continuous Play Guide Info Guide
25 Speaker/Setup Speaker Setup Setup or Menu
*
Intro Scan Menu Menu Menu Menu Menu Menu Menu
26 ⁄ Move/Adjust Up Up Up Up Up Up Up Up Up
27 fiMove/Adjust Left Left Left Left Left Left Left Scroll – Left Left
28 Set Set Enter Enter Select Enter Enter Enter Select Set Set/Enter
29 fl Move/Adjust Right Right Right Right Right Right Right Scroll + Right Right
30
¤
Move/Adjust Down Down Down Down Down Down Down Down Down
31 Digital/Open/Close Digital Input Select Open/Close Return/Exit
32 Delay/Status Delay Adjust Status or Return
*
Open/Close Prev Channel Prev Channel Prev Channel Prev. Channel
33 1111 1 1 11 1 11
34 2222 2 2 22 2 22
35 3 3333333333
36 4 444 4 4 44 4 44
37 5555 5 5 55 5 55
38 6 66666666 66
39 7777 7 7 77 7 77
40 8888 8 8 88 8 88
The
Bridge
TM
The
Bridge
TM
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 16

17
APPENDIX
*This command is not available when the DVD 37 (product code 007) has been programmed into the remote’s DVD mode.
NOTE: When any of the transport controls are pressed while the remote is in AVR, Video 2 or Video 3 mode, the remote will automatically switch to DVD mode and
the command will be applied to the DVD player. If you then press a button native to the original mode, e.g., Volume Down for the AVR, the remote will revert to the
original mode. See Punch-Through Programming, as described in the Advanced Functions section, for more information.
No. Button Name AVR Function DVD CD/CD-R Tape VCR (VID1) TiVo (VID1) CBL (VID2) SAT (VID2) TV (VID3/VID4) (DMP) XM HDMI 1/2
41 Tun-M/Zoom Tuning Mode Zoom or Chapter+
*
Repeat Tuning Mode
42 9999 9 9 99 9 99
43 0000 0 0 0 0 0 00
44 Memory/Playlist Memory Playlist or Audio
*
Time Memory
45 Tuning Up Tuning Up Next Chapter
*
Track Direct Cancel Cancel Sleep Tuning Up
46 Direct/Angle Direct Tuner Entry Angle Random Play FAV/Angle FAV Angle/FAV
47 Clear Clear Clear Clear Clear Clear Next Clear
48 Preset Up Preset Tune Up Slow Forward
*
+10 Alt Preset Up
49 Tuning Down Tuning Down Prev Chapter
*
Track Increment Tuning Down
50 Tone/P/I Tone Mode P/I Program Tone Mode Tone Mode Tone Mode Tone Mode
51 D. Skip Disc Skip (DVD) Disc Skip
*
Disc Skip Skip
52 Preset Down Preset Down Slow Rev
*
Preset Down
53 M1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1
54 M2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2
55 M3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3
56 M4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4
57 Dolby Surround Dolby Modes
58 DTS/A-B DTS Digital Modes A-B Repeat
59 DTS Neo:6 DTS Neo:6 Select
60 Night/Subtitle Night Mode Select Subtitle On/Off CDP Select
61 Logic 7/Random Logic 7 Select Random
62 Stereo/Repeat Stereo Mode Select Repeat
63 Skip Down Skip – (DVD) Step – Skip – Scan – Thumbs Down Skip – (DVD) Skip – (DVD) Skip – (DVD)
64 Skip Up Skip + (DVD) Step + Skip + Scan + Thumbs Up Skip + (DVD) Skip + (DVD) Skip + (DVD)
65 Dim Dimmer Dimmer
66 Rewind( ‹‹)R. Search (DVD) R. Search/Slow R. Search Rewind Rewind R. Search R. Search (DVD) R. Search (DVD) R. Search (DVD) Skip–/R. Search R. Search
67 Play (‹›)Play (DVD) Play Play R. Play/F. Play Play Play Play (DVD) Play (DVD) Play (DVD) Play Play
68 Fast-Forward (››) F. Search (DVD) F. Search/Slow F. Search Fast Fwd Fast Fwd F. Search F. Search (DVD) F. Search (DVD) F. Search (DVD) Skip+/F. Search F. Search
69 Record Record Record/Pause Record Record Record
70 Stop Stop (DVD) Stop Stop Stop Stop Slow Stop (DVD) Stop (DVD) Stop (DVD) Stop
71 Pause Pause (DVD) Pause Pause Pause Pause Pause (DVD) Pause (DVD) Pause (DVD) Pause Pause
72 Light Backlight Backlight Backlight Backlight Backlight Backlight Backlight Backlight Backlight Backlight Backlight Backlight
The
Bridge
TM
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 17

18
TV Manufacturer/Brand Setup Code Number
AIWA 027
A MARK 122 132
ADMIRAL 192
AKAI 123 160
AMPRO 164
ANAM 045 106 109 112 122
AOC 122 123 128
BLAUPUNKT 084
BROKSONIC 205 206
CANDLE 123 128
CAPEHART 059
CENTURION 123 171
CENTRONIC 045
CITIZEN 045 123 128 132
CLASSIC 045
CONCERTO 128
CONTEC 045
CORANDO 172
CORONADO 132
CRAIG 045 157 158 159
CROWN 045 132
CURTIS MATHES 123 128 132
CXC 045
DAEWOO 045 087 102 105 106 108 111 114 116 119
127 128 132
DAYTRON 128 132
DIGILINK 200
DYNASTY 045
DYNATECH 063
ELECTROHOME 115 132
EMERSON 045 123 128 132 139 157 158 159 162 205
FUNAI 045
FUTURETECH 045
GE 029 087 121 123 128 133 145 159 163
GOLDSTAR/LG 101 110 122 128 132
GRUNDIG 193
HALL MARK 128
HARMAN KARDON 201
HITACHI 123 128 132 147
INFINITY 148
INKEL 120
JBL 148
JC PENNEY 115 123 128 132 145
JENSEN 019
JVC 079 087 134
KAWASHO 173
KEC 045
KENWOOD 123 204
KMC 132
KTV 045 123 132 162
LLOYTRON 172 173
TV Manufacturer/Brand Setup Code Number
LODGENET 069
LOGIK 069
LUXMAN 128
LXI 077 145 148
MAGNAVOX 030 123 128 132 145 148
MARANTZ 115 123 148
MATSUI 148
MEMOREX 069 128
METZ 084
MGA 115 123 128
MINERVA 084
MITSUBISHI 077 115 123 128 160 167 168
MTC 175 176
NATIONAL 148 177 179 180 181 182
NEC 115 121 123 125
NIKEI 045
ONKING 045
ONWA 045
OPTONICA 077
ORION 207 208 209 210 211
PANASONIC 087 148 169
PHILCO 045 115 123 128 132 148
PHILIPS 033 034 035 036 123 128 132 145 148
PIONEER 024 123 128
PORTLAND 128 132
PROSCAN 133
PROTON 059 122 128 132 165
QUASAR 032 087
RADIO SHACK 045 128 132 180 196 197
RCA 021 115 123 128 133 145 161 163
REALISTIC 045 167 196
RUNCO 152 153
SAA 183
SAMPO 059 123 128
SAMSUNG 020 022 124 128 132 145
SANYO 026 054
SCOTT 045 128 132
SEARS 128 132 145
SHARP 077 128 132
SIEMENS 084
SIGNATURE 069
SONY 028 031 117 130 136 194 212
SOUNDESIGN 045 128
SPECTRICON 122
SSS 045
SYLVANIA 025 123 128 145 148
SYMPHONIC 184
TANDY 077
TATUNG 063
TECHNICS 181
TECHWOOD 128
APPENDIX
Refer to Tables A2 through A9 when programming the codes for your components into the remote.
Table A2 – Remote Control Product Codes – TV
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 18

19
VCR Manufacturer/Brand Setup Code Number
AIWA 040
AKAI 048 108 109 126
AMPRO 076
ASA 134
AUDIO DYNAMICS 018 048
BROKSONIC 110 147
CANDLE 134 135
CANON 135 140
CAPEHART 094
CITIZEN 134
CRAIG 045 116
DAEWOO 017 094 104
DAYTRON 094
DBX 018 048
DYNATECH 040
EMERSON 013 040 042 110 112
FISHER 017
FUNAI 040
GE 076 095 124
GO VIDEO 113
GOLDSTAR/LG 018 107
HARMAN KARDON 002 003 018 049
HITACHI 040 048
JC PENNEY 018 045
JENSEN 048
JVC 018 048 111 132
KENWOOD 020 048
LLOYD 040
LXI 020 040
MAGIN 045
MAGNAVOX 040
TV Manufacturer/Brand Setup Code Number
TEKNIKA 045 069 115 123 128 132
TELERENT 069
TERA 156
THOMSON 190 191
TMK 128
TOSHIBA 063 129 202
TOTEVISION 132
VIDEO CONCEPTS 160
VIDTECH 128
WARDS 069 128 132 148
YAMAHA 123 128
YORK 128
YUPITERU 045
ZENITH 069 090
ZONDA 122
APPENDIX
Table A3 – Remote Control Product Codes – VCR
Table A2 (continued)
VCR Manufacturer/Brand Setup Code Number
MARANTZ 018
MEMOREX 017 020 040 052 053 054 076
MGA 049
MITSUBISHI 049 131
MULTITECH 040
NAD 139
NATIONAL 140
NEC 018 048
NORDMENDE 048
OPTIMUS 159
ORION 147
PANASONIC 125 150 167 172
PHILCO 040
PHILIPS 040 075
PORTLAND 094
PULSAR 076
QUASAR 001 125
RADIO SHACK 055 134 140 142 158 159
RCA 095 124 125 157 172
REALISTIC 017 020 040 045 159
SALORA 020
SAMSUNG 045 051 095 105 109
SANSUI 048 116 147
SANYO 017 020
SCOTT 110 112
SEARS 017 020
SHARP 129 156
SONY 080 129
SOUNDESIGN 040
SYLVANIA 040
SYMPHONIC 040
TANDY 017 040
TASHICO 134
TATUNG 048
TEAC 040 048
TEKNIKA 040
THOMAS 040
TiVo 004 005 006 007 008 009 010 012
TMK 013
TOSHIBA 112 155
TOTEVISION 045
UNITECH 045
VECTOR RESEARCH 018
VIDEO CONCEPTS 018 040
VIDEOSONIC 045
WARDS 040 045 112
YAMAHA 018 040 048
ZENITH 040 050 076 083
Table A3 (continued)
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 19

20
CD Manufacturer/Brand Setup Code Number
ADCOM 063 069
AIWA 072 111 118 156 170
AKAI 050 177 184
AUDIO TECHNICA 053
AUDIOACCESS 125
AUDIOFILE 211
BSR 044
CALIFORNIA AUDIO 109
CAPETRONIC 070
CARRERA 087
CARVER 136 140 141 143 144 145 185 186
CASIO 117 166
CLARINETTE 166
DENON 187 188 213
EMERSON 052 093 108
FISHER 055 095
FRABA 117
FUNAI 126
GE 164
GENEXXA 108
GOLDSTAR/LG 016 087
HAITAI 099 214
HARMAN KARDON 001 002 025 054 190
HITACHI 093
INKEL 216
JC PENNEY 098 147
JENSEN 153
JVC 176 195 196
KENWOOD 030 062 078 079 148 151 176 178 181
LOTTE 108
LUXMAN 077 102
LXI 164
MAGNAVOX 039 113
MARANTZ 058 084 191 192 193
MCINTOSH 194
MCS 080 098
MITSUMI 152
MODULAIRE 166
NAD 013 074 197 198
NAKAMICHI 199 200 201
NEC 069
NIKKO 053 055
ONKYO 037 038 045 046 171 175 202 203
OPTIMUS 065 089 091 092 099 104 212
PANASONIC 075 109 119 158 183 204
PHILIPS 039 138 149 209
PIONEER 071 094 100 112 123 131 161 162 215
PROTON 210
QUASAR 109
RADIO SHACK 126 166 213
RCA 024 081 093 150
CD Manufacturer/Brand Setup Code Number
RCX 169
REALISTIC 058 093 095 104 105 108 164 166
SANSUI 047 081 134 157 172
SANYO 033 082 095
SCOTT 108
SHARP 058 105 114 151 159 167 180 181
SHERWOOD 003 041 058 105 133
SONY 103 115 116 118 132 139 163 205 206 207
208 212 217
SOUNDSTREAM 124
SYMPHONIC 059 110
TAEKWANG 177
TEAC 011 058 085 086 106 107 110 121 137 146
154
THETA DIGITAL 039
TOSHIBA 013 074 097 151 155 173
VECTOR RESEARCH 087
VICTOR 120 130
WARDS 095
YAMAHA 019 031 053 061 135 169
YORK 166
APPENDIX
Table A4 – Remote Control Product Codes – CD
DVD Manufacturer/Brand Setup Code Number
APEX DIGITAL 061
DENON 019 051
GE 003 004
GOLDSTAR/LG 005 055 064 066
HARMAN KARDON 001 002 007(Default) 068
JVC 006
MAGNAVOX 056
MARANTZ 059
MITSUBISHI 023
NAD 062
ONKYO 009 048
PANASONIC 024 030 044
PHILIPS 056
PIONEER 041 065
PROCEED 060
PROSCAN 003 004
RCA 003 004
SAMSUNG 053 054
SHARP 028
SONY 043 045
THOMSON 003 004
TOSHIBA 009 058 067
YAMAHA 030 063
ZENITH 005 055 064
Table A5 – Remote Control Product Codes – DVD
Table A4 (continued)
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 20