Harman Kardon ONYX User manual

harman/kardon Service Manual
ONYX STUDIO
Released EU2014 Harman International Rev 1, 12/2014
8500 Balboa Boulevard
Northridge, California 91329
QUICK-START GUIDE WITH SPECIFICATIONS 2
EXPLODED VIEW AND PARTS 4
BOM LIST 5
DISASSEMBLY MANUAL 6
CONTENTS
ASSEMBLY PROCEDURE 19
BLOCK DIAGRAM 32
PCB DRAWINGS 33
SCHEMATIC DIAGRAMS 40

詳細なオーナーマニュアルはこちらのサイト
をご覧ください
Pemilikpenuhmanual

Component Description Drawing No
MEOY261009A Fabric Grill Assy 1
MEOY261011A Front Radiator Assy 2
MEOY261001A Front Cover Sub Assy 3
S0S23001000 Soft Dome Tweeter 4
MEOY233003A
Soft Dome Tweeter Support Gaske
5
MEOY252002A Speaker Plate 6
S0A03180000 BT Antenna Assy 7
MEOY240004A Speaker Cable Assy 8
MEOY273002A Rubber Ring(Laser) 9
MEOY261007A IO Cover Assy 10
31OY2A1000A USB PCB Assy 11
MEOY261004A Back Cover Sub Assy 12
MEOY201005A Support Foot Right 13
MEOY273004A Support Foot Rubber Right 14
W0000301411 Screw_BTF_3*14.4MM 15
S0S00096000
Mid Woofer
16
W0003301011 Screw_BTP_3*10MM 17
31OY2K1000A Key PCB Assy 18
MEOY233024A Key PCB Gasket 19
W6000308410 Screw_MF_3*8.4MM 20
31OY2M1000A Main PCB 21
MEOY261006A Battery Cover Assy 22
BPOY2LG001B Battery Assy 23
31OY2A2000A IO PCB Assy 24
MEOY233020A IO PCB Gasket 25
W0000301011 Screw_BTF_3*10.4MM 26
MEOY201004A Support Foot Left 27
W0000301811 Screw_BTF_3*18.4MM 28
MEOY273003A Support Foot Rubber Left 29
MEOY261012A Back Radiator Assy 30

Harman Kardon Onyx Studio
Disassembly manual

Harman Kardon Onyx Studio
Disassembly manual
1. SERVICE DEVICES 維修工具
ESD-wristband
防靜電手環
ESD-gloves
防靜電手套
T10 Screwdriver
T10
螺絲起子
Plastic Plate
塑膠棒

Harman Kardon Onyx Studio
Disassembly manual
2. DISASSEMBLY INSTRUCTION 拆說明
1.把设备正面平放在工作台上
Put the device on the table as shown in
the figure.
2.用手取出 rubber support Left&Right.
Remove the rubber support Left and
support Right.
3.用螺丝刀取出右脚螺丝
Loosen the right screw_BB_3*18.2 by
screwdriver.
4.用螺丝刀取出左脚螺丝
Loosen the left screw_BB_3*18.2 by
screwdriver.

Harman Kardon Onyx Studio
Disassembly manual
5.取下右支架
Remove the right foot support.
6.取下左支架
Remove the left foot support.
7.用手或者工具从缺口位置掰开
Insert the tool into the gap as shown in
the figure and open it.
8.取下前網紗盖
Remove the front cover.

Harman Kardon Onyx Studio
Disassembly manual
9.用螺丝刀取出前盖螺丝*5
Loosen the 5 screws (BB_3*14.2mm) by
screwdriver.
10.从后面掰开后盖组件
Open the housing from the back cover.
11.打开上下壳
Open the housing.
12.拔下 DC-Connector
Release the DC-Connector.
1
2
3
4
5