Harman P35I Safety guide

Save These Instructions 3-90-775R36_09/15 www.harmanstoves.com
Owner's Manual
Installation and Operation
Model:
P35i
Pellet Fireplace Insert
#1-70-774195
#1-70-774235
SAVE THESE INSTRUCTIONS.
NOTICE
•Important operating
and maintenance
instructions included.
• Read, understand and
follow these instructions
for safe installation and
operation.
SAVE THESE INSTRUCTIONS
• Leave this manual with
party responsible for
use and operation.
Contact your local dealer with questions on
installation, operation or service.
P35i
Use & Care Video
Tested and approved for use with wood pellets only.
Burning any other type of fuel will void your warranty.
CAUTION
!
Check building codes prior to installation.
• Installation MUST comply with local, regional, state
and national codes and regulations.
• Consultlocalbuilding,reofcialsorauthorities
having jurisdiction about restrictions, installation
inspection, and permits.
CAUTION
!
Hot, will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
ammablematerials.
• Keepclothing,furniture,draperiesandotherammable
materials away.
HOT SURFACES!
Glass and other surfaces are
hot during operation AND cool
down.
WARNING
!
Please read this entire manual before
installation and use of this replace
insert room heater.
Failure to follow these instructions
could result in property damage, bodily
injury or even death.
• Donotstoreorusegasolineorotherammablevapors
and liquids in the vicinity of this or any other appliance.
• Donotoverre-Ifanyexternalpartstartstoglow,you
are overring. Reduce feed rate. Overring will void
your warranty.
• Comply with all minimum clearances to combustibles
asspecied.Failuretocomplymaycauseahousere.
WARNING
!
NOTE:
To obtain a French translation of this manual, please contact your dealer or visit www.harmanstoves.com.
Pour obtenir une traduction française de ce manuel, s’il vous plaît contacter votre revendeur ou visitez www.harmanstoves.com.
Do Not
Discard

2
Save These Instructions 3-90-775R36_09/15
TABLE OF CONTENTS
SafetyAlertKey:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the appliance or to property.
1 Welcome
A. Congratulations .................................3
2 Listing and Code Approvals
A. ApplianceCertication ............................ 4
B. Mobile Home Approval ............................4
C. GlassSpecications..............................4
D. Electrical Rating .................................4
E. BTU&EfciencySpecications .....................4
3 Special Warnings and Notes
A. CarbonMonoxideWarnings&Considerations .........5
B. OtherSafetyConsiderations .......................5
4 Getting Started
A. Design, Installation & Location......................6
B. Fire Safety .....................................6
C. Component Locator ..............................7
D. Pre-UseChecklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Dimensions and Clearances
A. Appliance Dimensions ............................ 9
B. Clearances to Combustibles ......................10
C. Floor Protection ................................10
D. MinimumFireplaceOpeningRequirements...........10
E. Mantel Projections .............................. 10
F. Factory Built Fireplace ........................... 11
6VentInformation 
A. Vent Termination Requirements .................... 12
B. AvoidingSmokeandOdors ....................... 13
C. Venting Requirements & Restrictions................14
D. ExistingFireplaceInstallation......................15
E. Rear Venting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
F. Zero Clearance Cabinet ..........................16
7 Mobile Home - (US Only)
A. Mobile Home Installation .........................17
8 Appliance Set-Up
A. OutsideAirAttachment...........................18
B. Installing the Surround ...........................19
C. Routing the Power Cord..........................19
D. Securing the Mounting Frame .....................20
E. Attaching the Venting ............................20
F. Installing the Body Into the Frame ..................21
G. Control Board Installation .........................21
H. Room Sensor Installation ......................... 21
I. FlameGuideExtension ..........................22
J. OptionalTrimKit................................22
K. Service Rail Kit.................................22
9 Operating Instructions
A. Fire Safety ....................................23
B. Fuel and Fuel Storage ...........................23
C. GeneralOperatingInformation.....................24
D. Before Your First Fire ............................26
E. Draft Test Procedure ............................26
F. Starting a Fire in "Automatic" Mode .................27
G. Maintaining a Fire...............................27
H. Shut-DownProcedure ...........................27
10 Troubleshooting
A. Troubleshooting Chart ...........................28
11 Service & Maintenance
A. Shut-DownProcedure ...........................29
B. QuickReferenceMaintenance.....................29
C. General Maintenance Procedure ...................30
D. Motors & Components ...........................34
12ReferenceMaterials
A. WiringDiagram.................................38
B. Loss of Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
C. Emergency Manual Ignition .......................39
D. Service Parts Lists ..............................40
E. Custom Surround Sizes ..........................44
F. WarrantyPolicy ................................45


3Save These Instructions3-90-775R36_09/15
A. Congratulations
Hearth&HomeTechnologieswelcomesyoutoourtraditionofexcellence!BychoosingaHarman®appliance, you have
become part of a long standing family committed to meeting the heating needs of consumers with the most distinctive,
powerful and responsible home heating products available.
TheP35iPelletInserthasbrilliantfeaturesinanelegantpackage,givingyouupto35,000BTUwhenyouneedit,automatically.
Asidefromtheregular,simplecleaningprocess,youneedonlysetyourdesiredroomtemperature,keepthehopperfull,
andtheashpanempty.WiththeP35i,youwillnoticeevenheatthroughoutyourzoneandalevelofconvenienceyounever
thoughtpossible.TheP35itakesadvantageofHarman®35+yearsofstovedesign,technologyandmanufacturing.Output
ismanagedbyamicroprocessorthatsensestheroomtemperatureandtheretemperaturewithtwothermistorprobesand
then determines the best feed rate for your heating demand. The platinum combination is Harman®Patented Pellet ProTM
Feedersystem,andESPControlwhichhavebeendevelopedtotheirhigheststate.Thesefeaturesworktogethertoallow
amazing heat output with little regard for fuel quality.
Wewishyouandyourfamilymanyyearsofenjoymentinthewarmthandcomfortofyourhearthappliance.
ThankyouforchoosingHarman®.
When This Room Heater Is Not Properly Installed, a
House Fire May Result. To Reduce The Risk Of Fire,
Follow The Installation Instructions. Contact Local
Building Or Fire Ofcials About Restrictions And
Installation Inspection Requirements In Your Area.
Thislabelislocatedontheinsideofthehopperlid.
Pleaserecordyourserialnumberforfuturereference.
SAMPLE
A division of
Hearth & Home Technologies
352 Mountain House Road
Halifax,PA17032
www.harmanstoves.com
1 Welcome

4Save These Instructions3-90-775R36_09/15
A.ApplianceCertication E.BTU&EfciencySpecications
2 Listing and Code Approvals
MODEL: P35i Pellet Insert
LABORATORY: OMNITestLaboratories,Inc
REPORT NO. 135-S-25-6.2
TYPE: SolidFuelRoomHeater/Fireplace
Insert
STANDARD(s): ASTME1509-12,ULC-S628-93,EPA
Method 28 & 5G
B. Mobile Home Approved
This appliance is approved for Installation in mobile/
manufactured homes. The structural integrity of the
mobile home oor, ceiling and walls must be maintained.
The appliance must be properly grounded to the frame of
the mobile home, and must never be installed in a room
designated for sleeping. The unit must have provisions for
an outside air source when installed in a mobile home.
C.GlassSpecications
This appliance is equipped with 5mm mirrored ceramic
glass. Replace glass only with 5mm mirrored ceramic glass.
Please contact your dealer for replacement glass if needed.
D. Electrical Rating
120 VAC, 60 Hz,
3.6Amps(Start-up);avg.1.5Amps(NormalRun)
EPACerticationNumber: 964-14
EPACertiedEmissions: 1.5g/hr
*LHVTestedEfciency: 78%
**HHVTestedEfciency: 69.5%
***EPA BTU Output: 9,600-28,800
****BTU Input 12,800-38,400
Vent Size: 4 Inch
Hopper Capacity: 41Lbs(19-1/2"Hopper)
62Lbs(23-1/2"Hopper)
Fuel WoodPellet
* Weighted average LHV efciency using data collected
during EPA emissions test.
**Weighted average HHV efciency using data collected
during EPA emissions test.
***A range of BTU outputs based on EPA Default Efciency
and the burn rates from the low and high EPA tests.
****Based on the maximum feed rate per hour multiplied by
approximately 8,600 BTU’s which is the average BTU’s from
a pound of pellets.
Thiswoodheaterhasamanufacturer-setminimumlowburn
rate that must not be altered. It is against federal regulations
to alter this setting or otherwise operate this wood heater
in a manner inconsistent with operating instructions in this
manual.
This wood heater needs periodic inspection and repair for
proper operation. It is against federal regulations to operate
this wood heater in a manner inconsistent with operating
instructions in this manual.
The P35i Pellet Insert is certied to
comply with 2015 particulate emission
standards. Not approved for sale after
May 15, 2020.
NOTE: This installation must conform with local codes.
In the absence of local codes you must comply with the
ASTM E1509-2004, ULC S628-93, (UM) 84-HUD

5
Save These Instructions 3-90-775R36_09/15
NEVER CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
SPECIAL NOTE:
DUE TO ASH BUILDUP, IT IS STRONGLY
RECOMMENDED TO HAVE YOUR STOVE
PROFESSIONALLY CLEANED AND SERVICED
ANNUALLY. THIS INCLUDES ALL PARTS OF
THE STOVE, AND THE VENTING SYSTEM.
Neverusegasoline,lanternfuel,kerosene,charcoallighter
uid,orsimilarliquidstostartor“freshenup”areinthis
heater. Keep all such liquids well away from the heater while
it is in use.
Installationandrepairofthisstoveshouldbedonebya
competentandqualiedprofessional.Werecommend
that the stove be inspected before use and at least
annuallybyaqualiedserviceperson.Periodiccleaning
is required throughout the heating season and at the end
ofeachwinterforthestovetoworkefciently.
DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT
OR SYSTEM.
3 Special Warnings and Notes
Carbon monoxide, referred to as CO, is a colorless,
odorless gas that is produced during combustion of solid
fuels. COistoxicandcanbefatal.
Even though this stove is designed to be as safe as
possible, it is recommended that you install a CO detector.
This is true for oil, gas, or wood burning products as well.
COisnotspecicallyheavierorlighterthanair.Therefore,
it is best to install the detector at table top level rather than
ontheceilinglikeasmokedetector.
COdetectorsareverysensitiveandmaysoundanalarm
forfumesotherthanCOorCOfromsourcesotherthan
thestovesuchasacarorlawnmowerexhaust.
Ifthealarmsounds
1. Increase house ventilation by opening windows or doors.
2.Makesurethestovedoorsandhopperlidareclosed
and latched.
3.Checkstoveforelectricalpowerandnormaloperation.
4.Checkventforpossibleblockageordown-draft.
5.Checkforfalsealarm.
WARNING
!
THIS WOOD HEATER HAS A MANUFACTURER-SET
MINIMUM LOW BURN RATE THAT MUST NOT BE
ALTERED. IT IS AGAINST FEDERAL REGULATIONS
TO ALTER THIS SETTING OR OTHERWISE OPERATE
THIS WOOD HEATER IN A MANNER INCONSISTENT
WITH OPERATING INSTRUCTIONS IN THIS MANUAL.

6Save These Instructions3-90-775R36_09/15
A. Design, Installation & Location Considerations
1. Appliance Location
Considerationmustbegiventosafety,convenience,trafc
ow,andthefactthattheappliancewillneedtobevented
to the outside. This appliance may only be installed into
an existing masonry or manufactured wood-burning
replace or using the optional zero-clearance cabinet
to build into a newly constructed chase. It is a good idea
toplanyourinstallationonpaper.Useexactmeasurements
forclearancesandoorprotection,beforeactuallybeginning
the installation.
Maintain specied vent clearance to combustible
requirements listed by the vent manufacturers instructions
and all appliance clearances as listed in this manual.
Check with your local building code agency before you
begin your installation. Local codes may supersede the
testlaboratoriesspecications.Alwaysobtainanyrequired
permit(s) so that insurance protection benets cannot be
unexpectedlycancelled.Ifanyassistanceisrequiredduring
installation, please contact your dealer.
Werecommendthataqualiedbuildinginspectorandyour
insurance company representative review your plans before
and after the installation.
2. Room Sensor Location
The room sensor's location will have some effect on the
appliance'soperation.Whenthesensorislocatedcloseto
the appliance, it may require a higher setting to keep the
rest of the house comfortable. If the sensor is located in
an adjacent room, or farther away from the stove, you will
notice higher temperatures near the appliance.
B.FireSafety
Maintain the designated clearances to combustibles.
Insulation must not touch the chimney. You must maintain the
designated air space around the chimney. This space around
a chimney is necessary to allow natural heat removal from
the area. Insulation in this space will cause a heat buildup,
which may ignite wood framing. NOTE: Clearances may
only be reduced by means approved by the regulatory
authority having jurisdiction.
To provide reasonable re safety, the following should be
given serious consideration:
1. Install at least one smoke detector on each oor of
your home. Detectors should be located away from
the heating appliance and close to sleeping areas.
Follow the smoke detector manufacturer's placement
and installation instructions, and be sure to maintain
regularly.
2. A conveniently located Class A re extinguisher to
contendwithsmallresresultingfromburningembers.
3. A practiced evacuation plan, consisting of at least two
escape routes.
4. Aplantodealwithahopperreasfollows:
Intheeventofahopperre:
a.Turnapplianceto"OFF".
b. Be sure hopper lid is closed and latched.
c. Notify Fire Department.
d.DoNOTpourwaterinthehopper.
e. Never pull the plug or otherwise disconnect the
powersupplytokillare.
• Do NOT connect this unit to a chimney flue
servicing another appliance.
• DoNOTconnecttoanyforcedairdistributionduct
or system.
CAUTION
!
Fire Hazard
• Do not operate appliance before
reading and understanding the
operating instructions.
• Failure to operate properly may
causeahousere.
WARNING
!
4 Getting Started
Installation and service of this
appliance should be performed by
qualiedpersonnel.Hearth&Home
Technologies recommends HHT
Factory Trained or NFI Certied
professionals.

7
Save These Instructions 3-90-775R36_09/15
C. Component Locations
Pellet Pro Feeder Frame Latch Ash Pan Latch
Feed Motor
Distribution Blower
Combustion Blower
Exhaust Sensing
Probe (ESP)
Do Not allow nish materials to block the air
owthroughthereturnairslots.
Door Latch
Viewing
Glass
Control Panel
Hopper Lid Latch
Return Air Slots
Ash Pan Cover

8Save These Instructions3-90-775R36_09/15
D. Pre- Use Check List
1. Placetheapplianceinalocationnearthenal
installation and follow the procedures below.
2. Opentheapplianceandremoveallarticles
packedinside.Inspectallitems for shipping
damage. Notify dealer of any missing or
damaged goods.
3. All safety warnings have been read and
followed precisely.
4. This Owner's Manual has been read in it's
entirety.
5. Floor protection requirements have been
read and followed.
6. The ue connector has been installed in
accordance with the instructions herein.
7. The proper clearances from the appliance
and chimney connector to combustibles have
been met.
8. The masonry chimney has been cleaned and
inspected by a professional, or the factory
built metal chimney is installed according to
the manufacturers instructions.
9. The chimney meets the minimum height
requirements.
10. All labels and hang tags have been removed
from the glass.
11. All plated surfaces have been wiped clean, if
applicable.
12. The room sensor and any additional cable
has been installed properly.
13. A properly grounded electrical receptacle
is available within reach of the unit's power
cord.
14. A good quality surge protector is highly
recommended to protect the electronics.
Fire Risk.
Hearth & Home Technologies
disclaims any responsibility for, and
the warranty will be voided by, the
following actions:
• Installation and use of any damaged appliance.
• Modicationoftheappliance.
• Installation other than as instructed by Hearth &
Home Technologies.
• Installation of substitute materials or replacement
parts not approved by Hearth & Home Technologies
• Operating appliance without fully assembling all
components.
• DoNOTOverre.
Oranysuchactionthatmaycausearehazard.
WARNING
!
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
• DoNOTinstalldamagedcomponents.
• DoNOTinstallincompletecomponents.
• DoNOTinstallsubstitutecomponents.
Report damaged parts to dealer.
WARNING
!

9
Save These Instructions 3-90-775R36_09/15
A. Appliance Dimensions
14”
356mm
22”
559mm
8”
203mm 10”
254mm
2”
50mm
24”
610mm
A
B
19-1/2”
495mm
Hopper
23-1/2”
597mm
Hopper
23-3/4”
603mm
9-1/4”
235mm
To Glass
A: 40" (1016mm) 46" (1168mm)
B: 31" (787mm) 34" (864mm)
Standard Surround
# 1-00-774221
Oversize Surround
# 1-00-774250
5 Dimensions and Clearances

10 Save These Instructions3-90-775R36_09/15
C. Floor Protection Requirements
Hearth extension must be of a non-combustible material.
It must extend beyond the appliance according to the
measurements listed.
MinimumSizeHearthExtensionis16"DeepBy32"Wide.
D. Minimum Opening for Masonry and
ManufacturedFireplaces
I
I
H
G
Location Inches Millimeters
MinimumWidth
Minimum Depth
MinimumHeight#1-70-774235
MinimumHeight#1-70-774195
HI
G
The Maximum mantel depth (J) is 12" (305mm) with a
minimumverticalheight(K)of12"(305mm).
K
J
E. Mantel Projections
B. Clearances to Combustibles - Masonry or
ManufacturedFireplace
THE CLEARANCES SPECIFIED ARE FOR YOUR
SAFETY! THESE CLEARANCES MAY ONLY
BE REDUCED BY MEANS APPROVED BY THE
REGULATORY AUTHORITY.
Mantel
Side Wall
Face Trim
A
B
C
E
D
F
609
368
597
495
24
14-1/2
23-1/2
19-1/2
C
D
B
A
Location Inches Millimeters
Insert to combustible sidewall
Surround top to face trim
Surround side to face trim
Inserttopto(max)12"mantel
330
0
25-7/16
305
13
0
1
12
F
F
E
E
Location Inches Millimeters
Windowopeningtofront-USA
Windowopeningtofront-CAN
Windowopeningtoside-USA
Windowopeningtoside-CAN
152
450
152
200
6
18
6
8