Harman Advance 1 Installation instructions

1-90-09730R 26_06/13
SAF ETY NOTICE
PLEASE R EAD THIS ENTIR E MANUAL BEF OR E INSTALLATION AND USE OF THIS PELLET F UEL-BUR NING R OOM
HEATER . F AILUR E TO F OLLOW THESE INSTR UCTIONS COULD R ESULT IN PR OPER TY DAMAG E, BODILY INJ UR Y ,
OR EV EN DEATH.
F OR USE IN THE U.S. AND CANADA. SUITABLE F OR INSTALLATION IN MOBILE HOMES
IF THIS HAR MAN® STOVE IS NOT PROPER LY INSTALLED, A HOUSE F IRE MAY RESULT. F ORY OUR SAF ETY , F OLLOW
INSTALLATION DIR ECTIONS.
CONTACT LOCAL BUILDING OR F IR E OF F ICIALS ABOUT R ESTR ICTIONS AND INSTALLATION INSPECTION
R EQ UIR EMENTS IN Y OUR AR EA.
CONTACT Y OUR LOCAL AUTHOR ITY (SUCH AS MUNICIPAL BUILDING DEPAR TMENT, F IR E DEPAR TMENT, F IR E
PR EV ENTION BUR EAU, ETC.) TO DETER MINE THE NEED F OR A PER MIT.
CETTE G UIDE D' UTILISATION EST DISPONIBLE EN F R ANCAIS. CHEZ V OTR E CONCESSIONNAIR E DE HAR MAN®
HOME HEATING .
SAV E THESE INSTR UCTIONS.
Installation & Operating Manual
Model(s):
Advance Freestanding Pellet Stove
NOTICE: SAVE THESE INSTRUCTIONS
Hot glass will cause burns.
• o not touch glass until it is cooled
• NEER allow children to touch glass
• eep children away
• CAREULLY SUPERISE children in same room as
stove.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
ammae matera
• eep clothing, furniture, draperies and other ammable
materials away.
HOT SUR F ACES!
Glass and other surfaces are hot during
operation and cool down.
WARNING
!
To obtain a rench translation of this manual, please
contact your dealer or visit www.harmanstoves.com
Pour obtenir une traduction franaise de ce manuel, sil
vous plat contacter votre revendeur ou visitez www.
harmanstoves.com
NOTE
Contact your local dealer with questions on installation,
operation or service.

31-90-09730R 26_06/13
 Nominale: 10,5 KW Réduite: 1,8 KW
Concentration CO (à 13 % O2)
à puissance nominale: < 0,02 % à puissance réduite: < 0,04 %
 à puissance nominale: 84 % à puissance réduite: 73%
The combustion air opening must not be obstructed.
 Les ouvertures d’air de combustion ne doit pas être obstruée.
Ne faites pas obstacle l’espace sous le réchauffeur. toujours fournir un
approvisionnement sufsant en air frais jusqu’au lieu d’installation applaince.
Tenir la porte frontale et le couvercle de trémie hermétiquement clos durant le
fonctionnement de l’appareil.
Model: Advance
Room Heater Pellet Fuel Burning
Also for use In Mobile Homes.
This this pellet burning appliance has been tested and listed for use In
Manufactured Homes In accordance with OAR 814-23-900 through 814-23-909
MINIMUM CEARANCES TO COMBUSTIBLES /
DISTANCE DE SECURITE PAR RAPPORT AUX

Back Wall / Entre Mur Arrière 1” (26mm)
Side Wall / Entre Paroi Latérale 10" (254mm)
Corner Installation / En Angle
Walls to Appliance 7” (178mm)
Entre Murs et Appareil
Flue Connector/ 5” (127mm)
Raccord à la cheminée
Floor Protection/Protection du Plancher
USA CANADA
Sides*/Côtés (A) 6” 200mm
Back/Arrière (B) 1” 200mm
Front*/Avant (C) 6” 450mm

*Mesurer à partir de la surface de la porte en verre
Use a non-combustible oor protector extending under
and to the sides, front and back of the unit as shown in
oor protection diagram. Measure front distance from
the surface of the glass door.
 Non-combustible oor protection
extended beneath the uepipe when installed with
horizontal venting.
Report #/Rapport #135-S-19-2, 135-S-19b-6.2
Test to/testé à ASTM E 1509-04, ULC/ORD -C1482-M1990, ULC-S627-00
Tested by Emitech, Apave & BFP Electronique; EN60335, EN 61000-3-2,
EN 14785:2005. Test date: February 2004
Room Heater, Pellet fuel Burning type, Also for use in Mobile Homes
“PREVENT HOUSE FIRES” Install and Use only in accordance with manufacture’s
installation and operation instructions. Contact local building or re ofcials about
restrictions and inspection in your area.
 Do not install appliance in a sleeping
room. An outside combustion air inlet must be provided. The structural integrity of the
manufactured home oor, ceiling and walls must be maintained.
Refer to manufacturer’s instructions and local codes for precautions required for
passing chimney through a combustible wall or ceiling. Inspect and clean exhaust
venting system frequently in accordance with manufacturer’s instructions.
Use a 3” or 4” diameter type “L” or “PL” venting system.
Do not connect this unit to a chimney ue servicing another appliance.
Do not obstruct the combustion air opening
Always provide an adequate supply of fresh air to the appliance installation location
FOR USE WITH PELLETIZED WOOD FUEL OR A SHELLED CORN/PELLET

Input Rating Max:5.7 lb. fuel/hr - 48,000 BTU/hour.
Electrical Rating: 240 VAC, 50 Hz, Start 2.6AMPS, Run 2.0 AMPS
U.S. Electrical Rating: 115 VAC, 60 Hz, Start 4.2 AMPS, Run 2.8AMPS

This model is exempt from
EPA certication under
40 CFR 60.531 by denition
[Wood Heater (A) “air-to-fuel ratio”].
A
A
C
B
USA
CANADA
Floor protector
BARCODE LABEL

Appareil de chauffage à granulé s de bois
U tilisable dans mobile homes
Essais Selon les normes 1509-04 de l’ASTM, ULC S627-00 et ULC-
C1482-M1990. Appareil de chauffage à granulés (UM) 84- HUD

NF EN 14785 CETIAT – Déc. 2006
AEMC MESURES EN50366 – Déc. 2006
EMITECH, APAVE & BFP Electronique – Fév. 2004
EN55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3
PREVENTION DES INCENDIES
Respecter scrupuleusement les instructions du constructeur pour l’installation
et les consignes de fonctionnement. Respecter les règles de sécurité en
vigueur dans votre région.
    Ne pas installer dans une
chambre. ll est inpératif de prévoir une prise d’air extérieur. L’intégrité
structurale du plancher, du plafond et des murs doit être strictment préservée.
Se reporter aux instructions du fabricant et aux réglementations spéciques
locales concernant les précautions requises lors de la traversée d’un mur ou
d’un plafond. Contrôler et nettoyer fréquemment toul le système d’évacuation
des fumées conformément aux recommandations du constructeur.
Utiliser des conduits « spécial granuléls » de diamètre 80 mm ou 100 mm.
Ne pas raccorder ce poêle à un conduit de cheminée déjà utilisé.

 L’utilisationd’autres combustibles est interdit
SE CONFORMER AUX INSTRUCTIONS D’UTILISATION
Consommation maximale: 2.16 kg/h - 48000 BTU/h.
Caractéristiques électriques (EUR): 240VC, 50 Hz, Intensité au démarrage
2.6 A, Intensité fonctionnement normal 2.0 A
Tenir le cordon d’alimentation à l’écart du poéle.
 Risque d’électrocution. Débrancher l’appereil avant toute
Intervention.
Ne remplacer la vitre qu’avec une vitre céramique de 5mm de même qualité
disponible auprès de votre revendeur.
Pour une information plus complète, se reporter à la notice d’utilisation.
ÉRICAINE POUR LA PROTECTION DE L’ENVIRONMENT
C
008
Serial No.
Node série:
Fuel Type: Wood Pellets, 5mm diameter, 20mm long
Shelled corn, when mixed with pellets
Route power cord away from unit.
DANGER: Risk of electrical shock. Disconnect power supply before servicing.
Replace glass only with 5mm ceramic available from your dealer.
For further instruction refer to owner’s manual.
Keep viewing and ash removal doors tightly closed during operation.

Emissions of CO in Combustion:
Normal Heat Output: <.02%, Reduced Heat Output: <.04%
Flue Gas Temperature: 224 C
Thermal Output: 10.5kW
Energy Efciency: Normal: 84%, Reduced: 73%
7"
178mm
7" 178mm
10" 254mm
1"
26mm
5 ” min.
5 ” min.
352 Mountain House Road, Halifax, PA 17032 (É.-U.)
Made in the U.S.A. of US and imported parts. / Fabriqué
aux États-Unis-d’Amérique par des pièces d’origine
américaine et pièces importées. Date of Manufacture / Date de fabrication
2 0 1 3 2 0 1 4 2 0 1 5 J AN F EB MAR APR MAY J UN J UL AUG SEP OCT NOV DEC
Manufactured by/Fabriqué par: Hearth and Home Technologies R ev D
P.N. 3 -9 0 -0 8 7 3 2
5.25”
1 1 .5 ”
Introduction
52 ountain House Road
Halifax, PA 1702
www.harmanstoves.com
Table of Contents
Automatic Operation 4
Manual Operation 6
ESP Control 8
Assembly & Installation 9
V enting 1 3
Maintenance 2 1
Trouble-Shooting 2 8
Speccatn 2
W iring Diagram 3 1
W arranty 3 2
Service Parts List 3 4
Corn Instructions 4 0
Power F ailures 4 1
The Advance Pellet Heater
This heating appliance does not ust have automatic ignition, it has total automatic temperature control. The Advance uses
a small room sensor rather than a wall thermostat for a more accurate temperature control.
The Advances control panel is designed for easy and efcient operation. It has 2 automatic modes of operation and 2 manual
modes of operation. The Advances specially designed burn pot and the Advance Igniter Automatic Ignition System, allow
the unit to burn a large variety of biomass fuels with varying ash content. The Advance feed system has a maximum feed
rate of  lbs. per hour and a minimum (maintenance) feed rate of 1.0 lbs. per hour.
This 0 to 8,000 BTU pellet stove has an accordion style heat exchanger system that allows maximum surface area for the
most efcient heat transfer in a smaller rebox.
The unit has an easy to clean combustion system with an ash pan that holds ash from 1 ton of burned premium pellets.
This unit is equipped with several different safety devices which will be explained later in this manual.
SAETY NOTICE: When installing a soid-fuel burning
appliance, the installation of smoke detectors and carbon
monoxide (CO) detectors is highly recommended. Note that
the paint curing process may take some time. It is good to
open a few windows near the appliance during the rst few
hours of burning, to eliminate unnecessary activation of the
smoke or CO detectors.
Note: This appliance is also approved for installa-
tion into a shop.
ppance ertcatn
Model: Advance Pellet Stove
Tested & Listed by: Omni-Test Laboratories
Type: Pellet Burning Room Heater
Standard(s): AST E150-0, ULC S27-00 and ULC
C182-10.
R eport # : 15-S-1b-.2
Please copy
your serial
number from the label on your
stove to the box below.
SER IAL NUMBER
SAMPLE LABEL ONLY
= Contains updated information



1-90-09730R 26_06/13
The Advance pellet stove is more than ust automatic ignition, it is also automatic temperature control.
The automatic system will allow the re size to be adusted to match the heating needs and even
put the re out if necessary. If heat is needed after the re is out, the Advance will automatically re-
ignite and adust the re size to match the heating need. The totally automatic room sensor mode is
recommended because of its efciency.
The unit can be switched between AUTO and ANUAL at any time during operation.
Automatic Ignition/ Operation
Room Temperature Mode: This setting will produce a room
temperature of 70 degrees with the distribution blower at medium
speed.
This setting will produce medium heat with the distribution
blower on "low".
This setting will produce continuous maximum heat output with
the distribution blower at full speed.
Stove Temperature Mode
R oom Temperature Mode
Igniter switch to " AUTO"
In Room Temp ode heat output is controlled automatically
by the Room Sensing Probe. When the Room Sensing Probe
calls for heat, the stove will increase output. When the Room
Sensing Probe is getting close to the set temperature, the
stove will begin to level off output and keep the re burning
at ust the right temperature to maintain that setting.
High output is determined by the feed rate setting. This
setting, generally on #, can be increased if higher burn
rates are necessary. The units maximum burn rate should
not create less than 1 of ash on the burn pot front edge.
See ig.2, Page 5. Overfeeding is not a safety concern, but
fuel may be wasted if unburned pellets fall into the ash pan.
In Room Temp ode a constant fuel consumption rate is
sacriced for exact room temperature. Therefore, as it gets
colder more pellets will be burned automatically.
The distribution blower speed will vary according to the
position of the mode selector pointer, and re size.
Stove Temperature Mode
Igniter switch to " AUTO"
This allows for automatic ignition upon start-up only. The
unit can then be set at any desired setting. The heat output
and fuel consumption will remain constant regardless of
room temperature. The units maximum feed rate should not
create less than 1 of ash on the burn pot front edge. See
ig 2, Page 5.
The units low burn or maintenance setting is as low as it will
go. It will not go out unless it runs out of fuel or is turned off.
To kill the re or stop burning the stove, turn the ode Selector
to O. This will cause the re to diminish and burn out. When
the re burns out and the stove cools down everything will stop.
If you pull the plug to shut down the stove, all motors will stop.
This may cause incomplete combustion and smoke in the rebox.
If the load door is opened the smoke may escape.
The best way to shut down the stove is simply let it run out of
pellets, then the stove will shut down automatically.
Shut-down procedure

51-90-09730R 26_06/13
Automatic Start Up
1. Fines are small pieces of broken pellets (sawdust). Fines do
not ow easily and often build up on the hopper funnel bottom
angles. These nes can be pushed into the feeder opening and
then ll the hopper with pellets. As the system works, they will
be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may purge too much
fuel into the burn pot causing excessive smoke on start-up.
3. The rebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door or the ash pan
door are open.
4. Adjust Feed Rate. If this is your rst re or you are trying different
pellets, set the feed adjuster to #4, Fig. 1. This is a conservative
number and will probably need to be increased. After you know
a feed rate setting that works well, use that setting. Remember,
if your feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of
the burn pot into the ash pan. Then scrape the holed surface
downward into the burn pot. When the stove is ignited these
scrapings will be pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on
"H". Set the Temperature Dial to #7. Allow the unit to burn for
about 30 minutes and check ash on front of burn pot. Fig. 2. If
the ash line is larger than 1", turn the feed adjuster from #4 to
#5. Allow another 30 minutes of burn time and check again. If
, at #6 setting, a 1" or less ash bed is not obtainable, it is not a
problem. The 1" ash bed is only a maximum burn rate and at
most normal settings the ash bed will be larger.
F ig. 1
See Note 7.
F ig. 2
1"
Igniter Switch to " AUTO" (up position)
ake sure the unit is plugged into a 120 AC, 0 H electrical
source. The power light should be the only light lit.
To avoid unwanted smoke, be sure there is no fuel or
combustibles in the ash pan prior to lighting.
1. Turn Mode Selector to " OF F " .
2. F ill hopper with pellets.
. Clean burn pot with scraper, if necessary.
. If starting after an empty hopper, turn F eed Adj uster
to " TEST" (for one 0 second cycle). This will feed pellets
into the auger tube and also allow you to check the motors
for operation. NOTE: The auger motor will not operate
with the view door or ash pan door open.
5. Turn F eed Adj uster to # 4 .
. F lip the Igniter Switch up into the AUTO position.
7. Turn the Temperature Dial to desired room temperature.
8. Turn Mode Selector to Room Temperature or Stove
Temperature.
. F ill hopper with pellets and remove ashes as required.
Starting F irst F ire
CAUTION
HOT WHILE IN OPERATION. EEP CHILREN,
CLOTHING AN URNITURE AWAY.
CONTACT AY CAUSE SIN BURNS.
CAUTION
EEP HOPPER LI, IRE OOR, AN ASH RAWER
PROPERLY CLOSE WHEN APPLIANCE IS IN
OPERATION.
CAUTION
DO NOT USE CHEMICALS OR FLUIDS TO START
THE FIRE. FOR EXAMPLE: NEVER USE GASOLINE,
GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO
START OR "FRESHEN UP" A FIRE IN THIS HEATER.
KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE
HEATER WHILE IT IS IN USE.

1-90-09730R 26_06/13
The Advance Pellet Stove is capable of manual operation. This also allows the operator to
manually control operation during an emergency (i.e. igniter failure.) The unit can be switched
between AUTO and ANUAL at any time during operation.
 t  pe t tart a re n ut an tc
to " Manual" at any time. Once an ignition cycle begins,
it will continue, regardless of mode.
Manual Ignition/ Operation
Room Temperature Mode: This setting will produce a room
temperature of 70 degrees with the distribution blower at medium
speed.
NOTE: During the use of this mode, if you keep increasing
te temperature a ettn t ncreae te re e te
distribution blower will automatically come on when the
ESP Temperature reaches 3 5 0 °F , or 8 1 % output.
This setting will produce a large viewing re without a distribution
blower operating.
Manual Stove Temperature Mode
R oom Temperature Mode
Igniter switch to " MANUAL"
The re will have to be lit with starting gel and a match, or
started automatically, see Automatic Operation. Switch to
anual position after the ignition cycle begins.
The difference between AUTO Room Temperature ode
and anual Room Temperature ode is that the re will not
go out as the room temperature goes above the control board
setting. The unit can only go to low burn and will remain there
until it runs out of fuel or until more heat is needed and the
feed rate increases. eed rate adustments and dial settings
are the same as AUTO settings.
Stove Temperature Mode
Igniter switch to " MANUAL"
The advantage of this mode is to allow the operator to have
a large viewing re without blowing extra heat into the room.
uring operation, with the temperature dial set at # or less,
the distribution fan will not operate. A # on the temperature
dial and a #5 on the feed aduster is approximately 80
output. It is not necessary to operate the distribution blower
below this point. Therefore, there can be a higher feed rate
( a larger viewing re) without an excess of hot air blowing
into the room.
An example of when to use the anual Stove Temperature
ode is if you want to watch a large re and the room is
already up to temperature. The Stove Temperature ode
allows you to have a larger re and a lower sound level,
without the distribution blower.

71-90-09730R 26_06/13
Manual Start Up
1. Fines are small pieces of broken pellets (sawdust). Fines do
not ow easily and often build up on the hopper funnel bottom
angles. These nes can be pushed into the feeder opening and
then ll the hopper with pellets. As the system works, they will
be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may purge too much
fuel into the burn pot causing excessive smoke on start-up.
3. The rebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door or the ash pan
door are open.
4. Adjust Feed Rate. If this is your rst re or you are trying different
pellets, set the feed adjuster to #4, Fig. 3. This is a conservative
number and will probably need to be increased. After you know
a feed rate setting that works well, use that setting. Remember,
if your feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of
the burn pot into the ash pan. Then scrape the holed surface
downward into the burn pot. When the stove is ignited these
scrapings will be pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on
"H". Set the Temperature Dial to #7. Allow the unit to burn for
about 30 minutes and check ash on front of burn pot. Fig. 5. If
the ash line is larger than 1", turn the feed adjuster from #4 to
#5. Allow another 30 minutes of burn time and check again. If
, at #6 setting, a 1" or less ash bed is not obtainable, it is not a
problem. The 1" ash bed is only a maximum burn rate and at
most normal settings the ash bed will be larger.
F ig. 4
F ig. 3
F ig. 5
1"
See Note 7.
CAUTION
DO NOT USE CHEMICALS OR FLUIDS TO START
THE FIRE. FOR EXAMPLE: NEVER USE GASOLINE,
GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO
START OR "FRESHEN UP" A FIRE IN THIS HEATER.
KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE
HEATER WHILE IT IS IN USE.
Igniter Switch to " MANUAL" (Down Position)
ake sure the unit is plugged into a 120 AC, 0 H electrical
source. The power light should be the only light lit.
To avoid unwanted smoke, be sure there is no fuel or
combustibles in the ash pan prior to lighting.
1 . Turn F EEDADJ USTER to desired feed rate. No.  is
good for most pellets.
2 . Turn the MODE SELECTORto “OF F ” and then to
the desired mode. This will reset control and start the
combustion motor.
3 . Turn the TEMPER ATUR E DIAL to the desired setting.
4 . Clean burn pot with scraper if necessary.
5 . F ill burn pot with pellets, only level with front edge.
(o Not Over ill).
6 . Apply starting gel on top of the pellets. Stir gel into
pellets for fast lighting.
SEE CAUTION BELOW . The use of a starting gel that is
commercially marketed for use with pellet stoves is permitted
ONLY when performing a cold start. Also be sure to perform
the above steps in sequence to ensure combustion blower
operation before applying the starting gel. ollow the starter
manufacturers instructions for proper application.
7 . Light with a match, and close the door. Operation will
begin when the re reaches the proper temperature.
8 . F ill hopper with pellets and remove ashes as req uired.
Starting F irst F ire

81-90-09730R 26_06/13
ESP Control
Feed adjuster
Sets the maximum feed
rate
Test
Runs all motors at full
speed for one minute to
check operation. Afterward
the combustion blower will
stay on low to simulate a
low burn rate.
Distribution Blower speed
adjustment range.
L = low
H = high
Variable speed anywhere
between L and H;
although as the stove
temp. goes up, so does
the low end of the scale.
3 Blinks: Indicates a poor ESP connection or that the ESP
(Exhaust Sensing Probe) has gone out of range too many
times. If the stove seems to be operating normally, perform
a manual reset.
4 Blinks: Can occur only in Room Temp ode and
indicates Room Sensing Probe failed or not installed. If a
Room Sensing Probe is then installed, the status light will
automatically reset.
NOTE: Unit will not start in AUTO with this status error.
5 Blinks (In Igniter Auto. Mode Only): Indicates that the
unit has failed to light after  consecutive igniter cycles, 2
minutes total. To reset - Turn ode Selector to O, then
turn to either mode again.)
6 Blinks : Indicates that the control has calculated poor or
incomplete combustion occurring for more than 25 minutes.
See Troubleshooting section for more details.
A six blink status may be set if the stove is allowed to run out
of pellets. To reset, turn mode selector to O then back
on to the desired mode. If the unit was not out of pellets, see
Troubleshooting section for more details.
* Manual reset- disconnect power cord for a few seconds
and reconnect. If error still occurs call your ealer.
Temp dial
Allows you to adjust the room temperature in Room
Temp Mode using the outer scale marked in degrees
Fahrenheit. It also allows you to adjust the stove
temperature while in Stove Temp Mode using the inner
scale marked from 1 to 7.
Mode Selector
Allows you to choose
between Room Temp Mode,
Stove Temp Mode, or OFF.
Also allows you to vary the
distribution blower speed by
turning the knob to the high
or low side of each mode.
Power Light
Indicates power to the
control.
Indicates power to the feed
motor.
Indicates power to
combustion blower
Status Light
Will be lit in either stove
or room temp mode when
pointer is not within off
position band except after
normal shut down. Blinks to
indicate errors listed below.
Indicates power to
distribution blower.
Dealer Diagnostic Port
For dealer maintenance only.
Requires special DDM monitor
supplied to Harman® Dealers
exclusively.
Status light error messages:
Indicates power to the
igniter.
Igniter switch
Set to appropriate Start-Up
mode.

1-90-09730R 26_06/13
Floor Protection
Floor Protection
Floor Protection
Consult with your local building code agency and insurance
representative before you begin your installation to ensure
compliance with local codes, including the need for permits
and follow-up inspections.
Several issues must be addressed when selecting a suitable
location for your Advance Pellet Stove. Observing required
clearances to combustible materials, the proximity to a safe
chimney or venting system, and the accessibility of electrical
supply must all be considered. In addition, selecting a location
that takes advantage of the buildings natural air ow is also
desirable to maximize the heating effectiveness of the heater.
In many cases, this is a central location within the building.
Place the stove on a noncombustible oor or a oor protector
that extends  (152mm) to the front,  (152mm) to the sides
and 1 (25mm) to the rear of the stove. In the US, the front
and side oor protection is measured from the door opening.
In Canada, the measurements are from the appliance. (ig. 8.)
loor protection must be placed under any horizontal venting.
This protection must extend a minimum of 2 (51mm) beyond
each side of the pipe.
n anaa yu may  maer S r prtectn
req uirements ONLY if the user agrees to completely
shut-down the appliance, and allow it to cool to where all
re  etnue an te cmutn er an t
ncatr t ut  prr t penn te re r
or ash door.
Place the stove away from combustible walls at least as far as
shown in gures , and 7. The clearance to a ceiling above the
appliance is 2 (08mm).
Note that the clearances shown are minimum for safety, but
do not leave much room for access when cleaning or servicing.
Please take this into account when placing the stove.
Mobile Home Installation
When installing this stove in a mobile home several
requirements must be followed:
1. The unit must be bolted to the oor. This can be done with
1 lag screws through the 2 holes in the base plate shown
in ig. 11, Page 10.
2. The unit must also be connected to outside air. See page 1.
. loor protection and clearances must be followed as shown.
. Unit must be grounded to the metal frame of the mobile
home.
5. WARNING - O NOT INSTALL IN A SLEEPING ROO.
CAUTION: This appliance must be vented to the outside.
The factory-built chimney must conform to CANULC-S2,
Standard for 50C actory-Built Chimneys. Use the vent or
chimney manufacturers components to provide an effective
vapor barrier where the vent penetrates to the exterior.
The top section(s) of chimney must be removable to a maximum
height of 1 (. ) to allow transport.
Installation and repair of this stove should be done by a
qualied service person. The appliance should be inspected
before use and at least annually by a qualied service person.
requent cleaning will be required. It is imperative that control
compartments, burners, and circulating air passageways of
the stove be kept clean.
Installation
CAUTION
THE STR UCTUR A L INTEG R ITY OF TH E
MANUF ACTUR ED HOME F LOOR, W ALL, ANDCEILING /
R OOF MUST BE MAINTAINED.
CAUTION
HOT W HILE IN OPER ATION.
K EEP CHILDR EN, CLOTHING, ANDF UR NITUR E AWAY .
CONTACT MAY CAUSE SK IN BUR NS.
ig. 7
10"
254mm
1 "
2 5 mm
L
J
F loor Protection
R eq uirements US Canada
Sides
Rear
 200mm
1 200mm
Kront  50mm
J
Canada
J
USA
K
L
NOTE:
easurement
 is measured
from the glass
in the US ONLY
7 " / 1 7 8 mm
7 " / 1 7 8 mm
ig. 
Alternate floor protector
dimension may be used
as long as they satisfy the
measurement requirements
shown below.
Minumum size oor protection
for a corner installation hearth
pad is 36" x 36".
The Clearance to The Top of The Unit is 0 (152cm)
easured rom The loor.

10 1-90-09730R 26_06/13
R emoving Side Doors
F ig. 1 0
Side Door Magnets
R emoving Side Doors for Installation
F igure 9
Use hand hole to swing open side doors to at least 0o.
F igure 1 0
Remove side doors by lifting upward on the door until the
bottom pin is out of its hole. ove the bottom of the door out
and away from the pedestal base about 12. Allow the door
to slide downward until the top door pin is out of its top hole.
NOTE: Always remove the side doors and rear shields to
move the unit. This will keep them from getting damaged.
R emoving the R ear Motor Shield Sheet Metal.
NOTE: isconnect power to the unit before removing the
motor shields. anger of electrical shock. Hot and moving
parts could cause inury.
F igure 1 1
There are (2) #10 hex head screws holding each rear shield.
Using a 51 nut driver or socket, loosen the (2) screws
about  or 5 turns.
F igure 1 2
Slide the rear shields straight outward until the ends come
out of the rear retaining clips, as seen in ig.1.
There are two bolts holding the stove to the pallet (see ig.
11) Remove the bolts to move the stove.
1. When replacing the shields, always insert the top and
bottom ends of the sheet metal into the retaining clips rst.
2. Slide the shields straight inward until the (2) hex head
screws are fully inserted into the stove slots.
. ake sure the top edges of the shield are against the
hopper bottom and tighten screws.
The rear shields are split around the ue tail pipe and outside
air knockout. This allows removal and installation of the rear
shields with the unit completely installed.
Placing R ear Shields Back on Unit
F ig. 9
Side Door
F ig. 1 1
Pallet Hold own Bolts
#10 hex head screws
Rear Shield Retaining clip
Outside Air nockout
F ig.1 3
Side Door
Hand Hole
F ig.1 2

11 1-90-09730R 26_06/13
These units are pre-tested at the factory with exactly 120
AC, 0 Hz. They are checked and adusted for rebox
tightness, gasket leakage, motor operation and igniter
operation. The Advance is then factory set at a mid-point
adustment and in most cases will not need any adustments.
NOTE: The factory low draft setting may not be correct
for the unit' s permanent installation conditions.
The control board on the Advance is equipped with a low draft
adustment port, located on the control face ust to the right
of the igniter light. See igure 1. This voltage adustment
is provided to allow the unit to be adusted for the household
voltage where the unit is going to be in permanent operation.
NOTE: The line voltage varies from area to area and often
home to home.
The low draft voltage should be adusted to achieve the most
efcient burn on low burn or maintenance. This voltage
adustment allows the installer to change the low voltage
set point approximately 15 volts. This adustment should
be done by the installer during set up because a draft meter
reading is req uired to insure proper set up.
If the unit is not adusted properly, it does not cause a safety
concern. If the unit is adusted too high, only efciency is lost.
If the unit is adusted too low, the low draft pressure switch
will not allow the feeder motor or the igniter to operate.
A simple draft test should be performed after completing the
ue pipe installation. To record the results for future reference:
1. Plug unit into a 120 AC, 0 H outlet.
2. Close the hopper lid, front view door, and the ash pan.
Neither pellets nor a re are required for this test.
. With the mode selector in the O position, turn the feed
aduster to TEST.
. Record the high draftin W.C. (Normal is -.50 to
-.0) The control will be on the High raft for a total of 2
minutes.
5. After 1 minute, the combustion motor will go down to low
draft and the distribution blower will go on high. Allow
approximately 15 seconds to pass for the combustion
motor to slow before checking the low draft.
. If the low draft is between .5 and .5, record the reading
 in W.C. If the reading is higher, slowly turn the
set screw counter-clockwise until the draft lowers. If the
reading is lower, very slowly turn the set screw clockwise
until the draft increases.
NOTE: In some cases, the draft may not go as low as .3 5
even with the set screw completely counter-clockwise.
Combustion Motor
Speed Control
Low draft only set
point.
The small straight
screwdriver slot is
plastic; therefore, the
unit can be adjusted
while in operation.
F ig. 1 4
raft eter bolt
hole location
F ig. 1 5 :
Low Draft V oltage Adj ustment

12 1-90-09730R 26_06/13
The room sensor is a small temperature sensor on the end
of a 0 gray or black wire. This sensor is installed much like
a standard wall thermostat. Because it is so small, it can be
hidden along the trim of a doorway or even up the leg of a
coffee table. There is a remote room sensor port on the rear
of the unit for easy external connection. Use standard 18-2
thermostat wire to extend the distance to the desired location
(50 maximum). The room sensor should be installed in the
location where you want to control the temperature.
NOTE: istances of more than 25 feet from the unit or in
another room are not recommended. It is recommended
that the room sensor be installed, even if only installed on
the rear of the unit as a return air sensor. The room sensor
is essential for the Advances excellent efciency.
Air G rill Installation
o not allow pellets or sawdust to build up on the hopper
lid gasket.
Inspect the hopper lid gasket for damage. A good hopper lid
seal is very important for proper operation.
Insert the two tail end hooks of the Air Grill Assembly up
under the stove top edge. Insert inward until the two center
hooks drop into the stove body slots in the front of the unit.
ig. 1
ig. 17
R oom Sensor and Air G rill Installation
R oom Sensor Installation
R EMINDER S
ig. 18
Hopper Lid Foam Gaskets
Room Sensor Outlet
Tail End HooksCenter Hooks

1 1-90-09730R 26_06/13
Avoiding Smoke and Odors
Negative Pressure, Shut-down, and Power F ailure:
To reduce the probability of back-drafting or burn-back in
the pellet burning appliance during power failure or shut-
down conditions, the stove must be able to draft naturally
without exhaust blower operation. Negative pressure in the
house will resist this natural draft if not accounted for in the
pellet appliance installation.
Heat rises in the house and leaks out at upper levels. This
air must be replaced with cold air from outdoors, which ows
into lower levels of the house. ents and chimneys into
basements and lower levels of the house can become the
conduit for air supply, and reverse under these conditions.
Outside Air:
Hearth & Home Technologies recommend attaching
outside air in all installations, especially lower level and
man r catn
Per national building codes, consideration must be given to
combustion air supply to all combustion appliances. ailure
to supply adequate combustion air for all appliance demands,
may lead to back-drafting of those and other appliances.
When the appliance is side-wall vented: The air intake is best
located on the same exterior wall as the exhaust vent outlet
and located lower on the wall than the exhaust vent outlet.
When the appliance is roof vented: The air intake is best
located on the exterior wall oriented towards the prevailing
wind direction during the heating season.
The outside air connection will supply the demands of the
pellet appliance, but consideration must be given to the
total house demand. House demand may consume some
air needed for the stove, especially during a power failure. It
may be necessary to add additional ventilation to the space in
which the pellet appliance is located. Consult with your local
HAC professional to determine the ventilation demands for
your house.
NOTICE: In Canada, ULC-S27 requires that all outdoor-
aired space heaters be secured to the structure.
ent nuratn
To reduce probability of reverse drafting during shut-
down conditions, Hearth  Home Technologies strongly
recommends:
• Installing the pellet vent with a minimum vertical run of
ve feet, preferably terminating above the roof line.
• Installing the outside air intake at least four feet below the
vent termination.
To prevent soot damage to exterior walls of the house and
to prevent re-entry of soot or ash into the house:
• aintain specied clearances to windows, doors, and air
inlets, including air conditioners.
• ents should not be placed below ventilated softs. Run
the vent above the roof.
• Avoid venting into alcove locations.
• ents should not terminate under overhangs, decks or
onto covered porches.
• aintain minimum clearance of 12 inches from the
vent termination to the exterior wall. If you see deposits
developing on the wall, you may need to extend this
distance to accommodate your installation conditions.
NOTE: Simpson DuraVent PelletVent Pro Harman®
Adapter Part # 3 PV P-ADHB and PelletVent Pro Harman®
Adapter Increaser Part # 3 PVP-X 4 ADHB are highly
recommended to be installed on the starter collar to
insure a proper pipe connection to the unit.
Hearth & Home Technologies assumes no responsibility
r nr e te arranty eten t mke amae
caused by reverse drafting of pellet appliances under
shut-down or power failure conditions.
V enting

1 1-90-09730R 26_06/13
USE 3 or 4 inch Pellet V ent pipe- (Type PL)
A combustion blower is used to extract the combustion
gases from the rebox. This causes a negative pressure in
the rebox and a positive pressure in the venting system as
shown in g. 1. The longer the vent pipe and more elbows
used in the system, the greater the ow resistance. Because
of these facts we recommend using as few elbows as possible
and 15 feet or less of vent pipe. The maximum horizontal
run should not exceed 8. If more than 15 feet of pipe is
needed, the diameter should be increased from  to . Be
sure to use approved pellet vent pipe wall and ceiling
pa-tru ttn t  tru cmute Be
sure to use a starting collar to attach the venting system to
the stove. All j oints for connector pipe must be fastened
with a minimum of three screws. F ollow pellet vent
manufacturer instructions for properly securing each
pellet vent j oint. The pellet starting collar must be
ecure t te unt ue car
Outside air is necessary in mobile homes and where building
codes require. The benet of outside air is mainly noticed in
small, very tight houses.
To install outside air use 2 8 I.. ex pipe part number
1-00-085. There is a break-away hole on the rear panel
which must be removed before connecting the ex pipe. The
pipe should be run outside and terminate to the side or below
the vent pipe outlet so the ue outlet is more than 12 from
the inlet cover. The maximum length run of this pipe is 15
feet. If a longer run is needed, the size must be increased
to . Inlet cover part number 1-10-052 should be used to
keep birds, rodents, etc. out of pipe.
V enting
Pellet venting pipe ( also known as PL vent ) is constructed
of two layers with an air space between the layers. This air
space acts as an insulator and reduces the outside surface
temperature to allow a clearance to combustibles of only 
inches or less. The sections of pipe lock together to form an
air tight seal in most cases however, in some cases a perfect
seal is not achieved. or this reason and the fact that the
Advance operates with a positive vent pressure, we specify
that the j oints also be sealed with silicone.
INSTALL V ENT AT CLEAR ANCES SPECIF IED BY THE
V ENT MANUF ACTUR ER .
CHIMNEY CONNECTOR MAY NOT PASS THR U AN
ATTIC, R OOF SPACE, CLOSET, F LOOR , OR CEILING .
V ent Pipe
Outside Air
ig. 1
+
+
-
= Positive static pressure
= Negative static pressure
+
-
Inlet Cover part# 1-10-08542
Flex pipe part# 1-00-08543
Outside Air Intake Connection
Room Sensor Connection Ports
Direct V ent W all Pass-through
The Harman® Direct V ent W all Pass-through (Part # 1 -0 0 -
6 7 7 0 7 7 ) makes installing your Harman® Pellet Stove with
ute ar muc eaer t  mae t t a rm  12 up
to 1 0 1 / 8 " thick with a sq uare opening of 6 " to 6 1 / 2 " .
Outdoor Half
Indoor Half

15 1-90-09730R 26_06/13
This method also provides excellent venting for normal
operation but requires the stove to be installed farther from
the wall. The vertical portion of the vent should be three to
ve feet high and at least three inches from a combustible
wall. This vertical section will provide natural draft in the event
of a power failure.
This method provides excellent venting for normal operation
and allows the stove to be installed closest to the wall. One
inch from the wall is safe however, two or three inches allows
better access to remove the rear panel. The vertical portion of
the vent should be three to ve feet high. This vertical section
will provide natural draft in the event of a power failure.
ig. 20
ig. 21
V enting
CAUTION
K EEP COMBUSTIBLES (SUCH AS G R ASS, LEAV ES,
ETC.) AT LEAST 3 F EET AW AY F R OM THE F LUE
OUTLET ON THE OUTSIDE OF THE BUILDING .
3 ft.
to combustibles
3 ft.
to combustibles
3 ft.
to combustibles
3 ft.
to combustibles
# 1 Preferred method
# 2 Preferred method

1 1-90-09730R 26_06/13
This method can be used for normal operation. This method
also provides natural draft in the event of a power failure. If
the chimney condition is questionable you may want to install
a liner as in method #.
This method can be used for normal operation. This method
also provides natural draft in the event of a power failure.
The damper area must be sealed with a steel plate (not
supplied). aowool, mineral wool or an equivalent non-
combustible insulation is recommended to be installed on top
of the sealing plate, to reduce the possibility of condensation.
A cap should be installed on the chimney to keep out rain. If
the chimney condition is questionable you may want to install
a liner all the way to the top as in ethod #5.
ig. 22
ig. 2
V enting
W AR NING !
THE CHIMNEY AND CONNECTOR MUST BE
MAINTAINED IN G OOD CONDITION AND K EPT CLEAN.
THE CHIMNEY MUST BE OF A TY PE SUITABLE F OR
SOLID-F UEL BUR NING .
 ntan nt an etn cmney
 ntan nt an etn repace cmney

17 1-90-09730R 26_06/13
This method provides excellent venting for normal operation.
This method also provides natural draft in the event of a
power failure.
In Canada and some places in the US it is required that the
vent pipe extend all the way to the top of the chimney.
In this method a cap should also be installed on the chimney
to keep out rain. Be sure to use approved pellet vent pipe
ttings. Seal pipe oints with silicone in addition to the sealing
system used by the manufacturer. Pipe size should be
increased to  using this method.
This method provides excellent venting for normal operation.
This method also provides natural draft in the event of a
power failure.
In Canada and some places in the US it is required that the
vent pipe extend all the way to the top of the chimney. The
pipe or liner inside the chimney should be  diameter.
In this method a cap should also be installed on the chimney
to keep out rain.
ig. 2
ig. 25
V enting
W AR NING !
THE CHIMNEY AND CONNECTOR MUST BE
MAINTAINED IN G OOD CONDITION AND K EPT CLEAN.
THE CHIMNEY MUST BE OF A TY PE SUITABLE F OR
SOLID-F UEL BUR NING .
5 ntan nt an etn repace cmney
 ntan nt an etn cmney

18 1-90-09730R 26_06/13
V enting
Through the ceiling vent, follow PL vent manufacturers
recommendations when using wall and ceiling pass through.
PL vent manufacturers
firestop spacer and
support.
No insulation or other
combustible materials
are allowed within  of
the PL vent pipe.
lashing
Storm collar
12 min.
 min.
 min.
ig. 2
 min.
It is recommended that outside air be installed with this
venting conguration.
CAUTION
eep any materials that may be affected by the
elevated exhaust temperatures at least  feet away
from the ue termination.
ig. 27
12
in. above
ground level
ig. 28
12" min. wall to outlet
S h ade d a r e a r e p r e sen t s
the minimum clearance to
combustible materials such as
shrubbery, mulch or tall grasses.
# 7 Installing through the ceiling vent nmum ue ent cnuratn

1 1-90-09730R 26_06/13
V enting
R eq uirements for Terminating the V enting
WARNING: enting terminals must not be recessed into a
wall or siding.
NOTE: Only pellet vent pipe wall pass-throughs and re
stops should be used when venting through combustible
materials.
NOTE: Always take into consideration the effect the
prevailing wind direction or other wind currents will cause
with yash andor smoke when placing the termination.
In addition, the following must be observed:
A. The clearance above grade must be a minimum of 12.
B. The clearance to a window or door that may be opened
must be a minimum of 8 to the side and 8 below the
windowdoor, and 12 above the windowdoor.
With outside air installed, the clearances are 1 8 " to the
side and below and 9 " above.
C. A 12 clearance to a permanently closed window is
recommended to prevent condensation on the window.
. The vertical clearance to a ventilated soft located above
the terminal within a horizontal distance of 2 feet (0 cm)
from the center-line of the terminal must be a minimum
of 18.
E. The clearance to an unventilated soft must be a minimum
of 12.
. The clearance to an outside corner is 11 from center of
pipe.
G. The clearance to an inside corner is 12.
H. A vent must not be installed within  feet (0cm) above
a gas meterregulator assembly when measured from the
horizontal center-line of the regulator.
I. The clearance to service regulator vent outlet must be a
minimum of  feet.
. The clearance to a non-mechanical air supply inlet to the
building or the combustion air inlet to any other appliance
must be a minimum of 8.
. The clearance to a mechanical air supply inlet must be a
minimum of 10 feet.
(with outside air installed, 6 feet )
L. The clearance above a paved sidewalk or a paved
driveway located on public property must be a minimum
of 7 feet.
. The clearance under a veranda, porch, deck or balcony
must be a minimum of 12 inches. (B Also Applies)
NOTE: The clearance to vegetation and other exterior
combustibles such as mulch is  as measured from the
center of the outlet or cap. This  radius continues to grade
or a minimum of 7 feet below the outlet.
Certain Canadian and or Local codes or regulations may
require different clearances.
A vent shall not terminate directly above a side-walk or
paved driveway which is located between two single family
dwellings and serves both dwellings.
Only permitted if veranda, porch, deck, or balcony is fully
open on a minimum of 2 sides beneath the oor.
NOTE: Where passage through a wall, or partition of
combustible construction is desired, the installation
shall conform to CAN/ CSA-B3 6 5 . (if in Canada)
V=Vent Terminal A=Air Supply Inlet =Area where termination is mot permitted
Door
Sidewalk
Fixed
Closed
Openable
Openable Fixed
Closed
Inside Corner
Detail
Porch or
Openable
Deck
or Fixed


20 1-90-09730R 26_06/13
DO NOT INSTALL A F LUE DAMPER IN THE EX HAUST
V ENTING SY STEM OF THIS UNIT.
DO NOT CONNECT THIS UNIT TO A CHIMNEY F LUE
SER V ING ANOTHER APPLIANCE.
INSTALL V ENT AT CLEAR ANCES SPECIF IED BY THE
MANUF ACTUR ER
Mobile home installation should be done in accordance
with the Manufactured Home and Safety Standard (HUD),
CF R 3 2 8 0 , Part 2 4 .
W AR NING
MOBILE HOME R EG ULATIONS DO NOT ALLOW
INSTALLATION IN A ROOM DESIGNATEDF OR
SLEEPING .
CAUTION
EEP COBUSTIBLES AWAY RO LUE OUTLET.
CAUTION
THE STR UCTUR AL INTEG R ITY OF THE MOBILE
HOME F LOOR , W ALL, ANDCEILING / R OOF MUST BE
MAINTAINED.
W AR NING
Keep combustible materials such as grass, leaves, etc.
at least 3 feet away from the point directly under the
vent termination.
Safety Information
DO NOT USE MAK ESHIF T COMPONENTS OROTHER
COMPR OMISES W HEN INSTALLING THIS APPLIANCE.
DO NOT CONNECT THIS APPLIANCE TO ANY AIR
DISTR IBUTION DUCT OR SY STEM. CAUTION
DO NOT BUR N G AR BAG E ORF LAMMABLE F LUIDS
SUCH AS G ASOLINE, NAPTHA OR ENG INE OIL.