Harman Advance Pellet Stove Installation instructions
A
A
C
B
USA
CANADA
Floor protector
Date of Manufacture / Date de fabrication
2012 2013 2014 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
Modèle : Advance
Appareil de chauffage à granulés de bois
Utilisable dans mobile homes
Harman Advance Pellet Stove
Label measures: 5.25" high X 11.5"wide
008
7"
178mm
7"
178mm
10"
254mm
1"
26mm
5” min.
5” min.
This setting will produce a room
temperature of 70 degrees with the distribution blower at medium
speed.
This setting will produce medium heat with the
distribution blower on "low".
This setting will produce continuous maximum heat
output with the distribution blower at full speed.
1. Fines are small pieces of broken pellets (sawdust). Fines do not
ow easily and often build up on the hopper funnel bottom angles.
These nes can be pushed into the feeder opening and then ll
the hopper with pellets. As the system works, they will be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may purge too much
fuel into the burn pot causing excessive smoke on start-up.
3. The rebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door or the ash pan
door are open.
4. Adjust Feed Rate. If this is your rst re or you are trying different
pellets, set the feed adjuster to #4, Fig. 1. This is a conservative
number and will probably need to be increased. After you know a
feed rate setting that works well, use that setting. Remember, if
your feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of the
burn pot into the ash pan. Then scrape the holed surface downward
into the burn pot. When the stove is ignited these scrapings will be
pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on "H".
Set the Temperature Dial to #7. Allow the unit to burn for about 30
minutes and check ash on front of burn pot. Fig. 2. If the ash line is
larger than 1", turn the feed adjuster from #4 to #5. Allow another
30 minutes of burn time and check again. If , at #6 setting, a 1" or
less ash bed is not obtainable, it is not a problem. The 1" ash bed
is only a maximum burn rate and at most normal settings the ash
bed will be larger.
See Note 7.
1"
This setting will produce
a room temperature of 70 degrees with the distribution
blower at medium speed.
This setting will produce a large viewing re without a
distribution blower operating.
1. Fines are small pieces of broken pellets (sawdust). Fines do not
ow easily and often build up on the hopper funnel bottom angles.
These nes can be pushed into the feeder opening and then ll
the hopper with pellets. As the system works, they will be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may purge too much
fuel into the burn pot causing excessive smoke on start-up.
3. The rebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door or the ash pan
door are open.
4. Adjust Feed Rate. If this is your rst re or you are trying different
pellets, set the feed adjuster to #4, Fig. 3. This is a conservative
number and will probably need to be increased. After you know a
feed rate setting that works well, use that setting. Remember, if your
feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of the
burn pot into the ash pan. Then scrape the holed surface downward
into the burn pot. When the stove is ignited these scrapings will be
pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on "H".
Set the Temperature Dial to #7. Allow the unit to burn for about 30
minutes and check ash on front of burn pot. Fig. 5. If the ash line is
larger than 1", turn the feed adjuster from #4 to #5. Allow another
30 minutes of burn time and check again. If , at #6 setting, a 1" or
less ash bed is not obtainable, it is not a problem. The 1" ash bed
is only a maximum burn rate and at most normal settings the ash
bed will be larger.
1"
See Note 7.
Sets the maximum feed
rate
Runs all motors at
full speed for one
minute to check
operation. Afterward the
combustion blower will
stay on low to simulate
a low burn rate.
Distribution Blower
speed adjustment
range.
L = low
H = high
Variable speed
anywhere between L
and H; although as the
stove temp. goes up, so
does the low end of the
scale.
Allows you to adjust the room temperature in
Room Temp Mode using the outer scale marked in
degrees Fahrenheit. It also allows you to adjust the
stove temperature while in Stove Temp Mode using
the inner scale marked from 1 to 7.
Allows you to choose
between Room Temp
Mode, Stove Temp Mode,
or OFF. Also allows you
to vary the distribution
blower speed by turning
the knob to the high or
low side of each mode.
Indicates power to the
control.
Indicates power to the
feed motor.
Indicates power to
combustion blower
Will be lit in either stove
or room temp mode
when pointer is not within
off position band except
after normal shut down.
Blinks to indicate errors
listed below.
Indicates power to
distribution blower.
Dealer Diagnostic Port
For dealer maintenance only.
Requires special DDM monitor
supplied to Harman Dealers
exclusively.
Indicates power to
the igniter.
Set to appropriate Start-
Up mode.
6"
(152mm)
6" (152mm)
FLOOR
PROTECTOR
6"
(152mm)
1"
7"
178mm
7"
178mm
10"
254mm
1"
25mm
Side Door
Magnets
Side Door
Side
Door
Pallet Hold Down Bolts
Rear Shield Retaining clip
Outside Air Knockout
Rear
Shield
The small straight
screwdriver slot is
plastic; therefore,
the unit can be
adjusted while in
operation.
Hopper Lid
Foam Gaskets
Inlet Cover part# 1-10-08542
Flex pipe part# 1-00-08543
Outside air ex pipe
goes here
Room Sensor
Connection Ports
+
+
-
= Positive static pressure
= Negative static pressure
+
-
Fig. 26
Fig. 27
Fig. 28
12" min. wall to outlet
Keep combustible materials such as grass,
leaves, etc. at least 3 feet away from the point
directly under the vent termination.
Other manuals for Advance Pellet Stove
2
Table of contents
Other Harman Pellet Stove manuals
Harman
Harman PP38 plus User manual
Harman
Harman Advance Pellet Stove Installation instructions
Harman
Harman P68 Installation instructions
Harman
Harman P35I User manual
Harman
Harman Accentra Freestanding Pellet Stove Installation instructions
Harman
Harman PC45 Installation instructions
Harman
Harman P43 User manual
Harman
Harman XXV Freestanding Pellet Stove User manual
Harman
Harman Advance Freestanding Pellet Stove Installation instructions
Harman
Harman P43 User manual
Harman
Harman XXV Installation instructions
Harman
Harman P68 Installation instructions
Harman
Harman P43 User manual
Harman
Harman P61 User manual
Harman
Harman XXV Freestanding Pellet Stove User manual
Harman
Harman Advance Pellet Stove Operating manual
Harman
Harman P43 User manual
Harman
Harman The Accentra Pellet Stove Installation instructions
Harman
Harman XXV User manual
Harman
Harman PP38+ Installation instructions
Popular Pellet Stove manuals by other brands
Lopi
Lopi Foxfire AGP manual
Enviro
Enviro Omega Technical manual
EdilKamin
EdilKamin DANIA Air Tight Plus Installation, use and maintenance
Vistaflame
Vistaflame VF-55-FS Technical manual
Quadra-Fire
Quadra-Fire CB1200M-MBK installation manual
Piazzetta
Piazzetta MP 938 Instructions for installation, use and maintenance
