Harman Infinity KAPPA 6 User manual

l\JInfinity
HARMAN
INFINITY KAPPA 6, KAPPA 8, AND
KAPPA 10 MARINE SPEAKER
Infinity Kappa 6, Kappa 8, and Kappa 10 marine speaker - Owner's Manual -
Haut-parleur marine Infinity Kappa 6, Kappa 8 et Kappa 10- Mode D'emploi -
Altavoz para entornos marinoss Infinity Kappa 6, Kappa 8y Kappa 10 - Manual de Propietario DIii
Infinity Kappa 6, Kappa 8 II Kappa 10 MJlUIJaH - fflP.JfJIJ BIi
Infinity Kappa 6, Kappa 811 Kappa 10 IIIDJ\-llfii.Jfl& Bil
Marine speaker laut Infinity Kappa 6, Kappa 8, dan Kappa 10 - Panduan Pengguna
lnfinity(1'~7-<=Y-<) Kappa 6, Kappa 8' Kappa 10~
1
J-~•A~-1J- -lifiit~I
Infinity Kappa 6, Kappa 8i Kappa 10 Marine DtiM ~lll~ ->.tixt l'ltAi
-
-
-

-
~Infinity
HARMAN
INFINITY KAPPA 6, KAPPA 8, AND
KAPPA 10 MARINE SPEAKER
THANK YOU FOR YOUR PURCHASE ...
Your Infinity product has been designed to provide you with the performance and ease of operation you would expect from
Infinity.
ABOUT THE MANUAL
This manual describes general installation guidelines. However, please note that proper installation of marine audio
components requires qualified experience. If you do not have the knowledge and tools to successfully perform this
installation, we strongly recommend consulting an authorized Infinity dealer about your installation options. Keep all
instructions and sales receipts for reference.
WHAT'S IN THE BOX
Kappa6
0-, 12x
(C
>)
lX
Kappa 10
~
1X
~ 6X CJ§JilX
~ Mg .. o
(C
>) ~
IX
DIMENSIONS
Kappa6
5-23/32" 144. 8mm
Kappas
0--- •2ll
Kappas
7" 177.4mm

Kappa 10
SPEAKER SIGNAL WIRING
To send signal to the Infinity marine speaker, connect the positive(+) and negative(-) speaker wires to the appropriate
speaker outputs of your source unit or amplifier. Be sure to observe proper polarity.
SPEAKER LED WIRING
To provide power for the LEDs, plug the 24-gauge black(+), blue, green, and red LED wires from the speaker into the
included female connector, then run the wires from the female connector toyour compatible 12-volt power source or light
controller (~old separately). If using a separate controller, be sure to connect each wire to the proper output.
Blue
Red
Black
To speaker _,.
_. =( ="L-..d----\--t:=1---=-==-=-==-=-==-==-==-==-==-==-==-==-==================
If hardwiring the LEDs directlyto your power source, you can choose the color of the LEDs by connecting the black wire to
the positive(+) terminal, and the appropriate R, G, and/or B single wire or combination of wires to the negative(-) terminal.
There are 7 possible colors, depending on the wiring configuration you choose:

Wire connected to positive Wire connected to
Color produced
(+12V) terminal negative(-) terminal
Red Red
Green Green
Blue Blue
Black
Red+ Green
Yellow
Red+ Blue
Purple
Blue+ Green
Aquamarine
Red + Blue + Green
White
APPLYING FOAM SEAL
To help seal your installation against water, and to provide an airtight acoustic seal, apply the self-adhesive foam seal to the
speaker frame.
-MOUNTING THE SPEAKER
Use the included screws to mount the speaker to the location. Use the included speed clips if necessary to provide a secure
mount.
NOTE: Use caution when cutting and using screws with fiberglass to prevent scratches and cracks.
Kappa 6 and Kappa 8 Kappa 10

REMOVING THE TWEETER FOR SEPARATE MOUNTING (KAPPA 8 ONLY)
Use the included 2-pin tool to remove the tweeter from the woofer housing. Place the pins of the tool in the holes of the
tweeter grille and rotate 45 degrees clockwise to loosen and remove.
) 45'
FLUSH-MOUNTING THE TWEETER
Place the tweeter in the mounting bracket and use the tool to secure by turning 45 degrees counter-clockwise.
A
..
/ 45•
..
To transmit audio signal to the tweeter, make sure the woofer and tweeter are connected with the included cable.
C
-

Place the tweeter in the mounting location, then turn each setscrew clockwise to tighten mounting brackets. Use caution so
as not to overtighten. Snap the included outer ring over the mounting bracket to hide the setscrews.
---
Specifications Kappa&
Kappas Kappa 10
Continuous power 100W 200W 300W
handling
Peak powerhandling 300W 500W 900W
Frequency response
40Hz-25kHz 30Hz-22kHz 20Hz-2kHz
Nominal impedance 3 Ohms* 3 Ohms* 2 or 4 Ohms (use
switch to select)
Sensitivity
92d8 92d8
89d8
External diameter 7-15/32" (189.4mm) 9-1
/2" (241 mm) 11-5/8" (295mm)
Mounting cutout diameter 5-23/32" (144.8mm) Woofer: 7" (177.4mm) 9-9/16" (235.6mm)
Tweeter bracket: 4-9/16"
(115.9mm)
Total depth 3-21/32" (92.5mm) 4-9/32" (108.1 mm) 6-13/32"
(162.4mm)
Mounting depth 2-9/16" (65mm) 3-3/16" (80.5mm) 4-7/8" (123mm)
- *NOTE: Because of the woofer's low impedance, do not wire two or more in parallel to an amplifier; doing so can result in
overheating and damage to the amplifier.
~
HARMAN
~
HARMAN International Industries,
Incorporated 8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.infinityspeakers.com
@ 2018 HARMAN International Industries, Incorporated. All rights reserved.
Infinity is a trademark of HARMAN International Industries, Incorporated,
registered in the United States and/or other countries. Features, specifications
and appearance are subject to change without notice.

TRQ5608_A