Harrod FBL-167 User manual

FBL-167
PVC Futsal Goal
INS715
02/02/2016 Revision 8
Harrod UK Limited©
Code:
Product:
Pack Contents:
View of Product
1. PLP115 L/H Corner joint with spigot x1
2. PLP116 R/H Corner joint with spigot x1
3. PLP090 Centre support tube with label x1
4. PLA086 Top upright tube with label x2
5. PLP107 Poly Goal joint tube x8
6. PLA111 Bottom upright & Crossbar joint x4
7. PLA110 Post Corner Joint x2
8. PLA087 Top net support tube x2
9. CLP118 Small button clip x10
10. CLP119 Large button clip x28
11. CLP040 Net Clips x36
12. PLA107 Net support connector x2
13. PLA088 Back net Support tube x4
14. PLA126 Net support connector x2
15. PLA125 Bottom Corner connector x2
16. PLP091 Bottom Sidebar tube with hole x2
17. PLA089 Bottom /Side bar tube with label x4
18. PLP121 Bottom centre connector tube x1
19. PEG020 U-Peg x4
20. FBL-155 Carry Bag x1 (Not Shown)
21. FBL-156 Futsal net x 1 (Not Shown)
IMPORTANT PLEASE READ THE
ASSEMBLY INSTRUCTIONS
CAREFULLY BEFORE STARTING
TOASSEMBLEYOUR GOAL
11
IF USED ON A SYNTHETIC PITCH, THE GOALS MUST BE SUITABLY ANCHORED
TO CONFORM TO BS 8462-1:2005. THIS CAN BE ACHIEVED BY EITHER,
A) INSTALLING A GROUND ANCHOR BELOW THE SYNTHETIC GRASS LEVEL
B)BY ATTACHING THE GOAL TO THE NEAREST PERIMETER FIXING POINT, A
CHAIN OR FLAT BAR CAN BE USED TO ACHIEVE THIS, BUT CARE SHOULD BE
TAKEN SO AS TO NOT CREATE ANOTHER POTENTIAL HAZARD WHEN
INSTALLING THIS OPTION.
C)ATTACHING COUNTERBALANCE WEIGHTS (35 IN TOTAL OR 2 X ANC-005
ANCHORS) TO THE BACK OF EACH GOAL.
PLEASE CONTACT YOUR DISTRIBUTOR FOR ADVICE ON ATTACHMENT OPTIONS.
kg
9
10
19
3
2
17
16
7
18
15
6
5
4
1
6
13
14
13 8
12
17 Important: Plastic Goals be
exposed to sub zero temperatures, store inside
during cold weather - Failure to do so may
result in goal damage.
MUST NOT

PLP090 CROSSBAR CENTRE 572mm Long X1
PLP121 BACKBAR CENTRE 572mm X1
PLA086 TOP UPRIGHT 694mm Long X2
PLP115
TOP ELBOW
LEFT HAND
X1
PLP116
TOP ELBOW
RIGHT HAND
X1
PLP107 LARGE
CONNECTOR X8
PLP091 SIDEBAR BOTTOM
NETBAR SUPPORT 694mm X2
PLP089 SIDEBAR SUPPORT TUBE 1142mm X4
PLA107
NET SUPPORT
ELBOW JOINT X2
PLA111 SIDEBAR BOTTOM SUPPORT 1142mm X4
PLA125
UPRIGHT & SIDEBAR
CONNECTOR X2
PLA110
SIDE & BACKBAR
CONNECTOR X2
PLA126 NET SUPPORT
CONNECTOR X2
PLA087 TOP NET SUPPORT 760mm X2
PLA088 BACK NET SUPPORT 1114mm X 4
PART LIST FOR FBL-167 - PVC FUTSAL GOAL
(3) (4)
(15) (7) (2) (1)
(5) (18) (12)
(16) (14)
(17)
(6)
(8)
(13)

ASSEMBLY INSTRUCTIONS FOR FBL-167 - PVC FUTSAL GOAL
1.PLEASE NOTE: Before assembling the goal layout all the parts on the ground where you intend to
assemble the goal so that you can make sure that all the parts are present and correct.
All connector parts have button clips already inserted into them. When assembling the goal, gently
squeeze the button clips down low enough to slide the tubes over them. Then make sure that the button
clips are inserted into the holes provided on the tubes. This will make sure that the tubes are fastened
together correctly.
165562
3
2. Assemble the crossbar by inserting the corner connectors (1 & 2
PLP115/116) into the large crossbar connector (6 PLA111), now insert connector (5 PLP107) into
each end then join up the rest of the cross bar using (3 PLP090).
CROSSBAR ASSEMBLY:
77
17
5
18
5
17
MAKE SURE ANCHOR LABELS ARE ON THE END
3. Assemble the backbar by inserting the corner connector (7 PLA110) into
the backbar tube (17 PLP089) making sure that the label is at the same end as the corner joint. Now
insert connector joint (5 PLP107) into the end of each part then connect all together using (18 PLP121)
BACKBAR ASSEMBLY:
H
A
R
R
O
D
6
5
4
4. Assemble the upright by inserting connector (5 PLP107) into the bottom
upright (6 PLA111), to complete the upright insert (4 PLA086) onto (5 PLP107) do this for both sides.
NOTE. Make sure that Harrod sticker is facing the correct way up as shown in diagram above.
UPRIGHT ASSEMBLY:
Label Button Clip
Button Clip

ASSEMBLY INSTRUCTIONS FOR FBL-167 - PVC FUTSAL GOAL
8
13
14
12 13
5. NET SUPPORT ASSEMBLY: Connect (12 PLA107) to the top net
support (8 PLA087), then connect back net support (13 PLA088). Once
the has been done connect the centre net support (14 PLA126) and (13
PLA088) to rest of the upright do this for both sides
16
5
17
6. Insert connector (5 PLP107) to the longest sidebar tube (17 PLP089),
then connect the next tube (16 PLP091) do this for both sides.
SIDEBAR ASSEMBLY:
Make sure the anchor label is this end
15
15
Crossbar Assembly
Backbar Assembly
Sidebar Assembly
Sidebar Assembly
Upright Assembly
Upright Assembly
7.CONNECTION OF BACKBAR,
SIDEBARS, UPRIGHTS & CROSSBAR:
Lay the 2 sidebars on the ground and then
connect the backbar to the sidebars,
making sure that the button clip are
secure in the hole once assembled.
Lay the the 2 uprights on the ground and
then connect the crossbar to the uprights,
making sure the button clips are secure in
the hole once assembled.
Now connect the sidebar and upright joint
(15 PLA125) to the sidebars as shown in
the diagram left. Then connect the upright
and crossbar assembly to the sidebars.
With the aid of a second person slide the
upights onto (15 PLA125) and secure into
place with button clips.

ASSEMBLY INSTRUCTIONS FOR FBL-167 - PVC FUTSAL GOAL
SIDEFRAME ASSEMBLY
8. NET SUPPORT ASSEMBLY: Connect the top net support to the top corner spigot of
the crossbar making sure that button clip is secure in the
hole, do the same to the otherside.
Once the top net support has been
connected correctly, push the bottom bar
into the support hole on the side bar to
secure the net support. Do the same to the
other side to complete the goal.
9. Lay the net (21 FBL-156) on the ground identify the edge of the
crossbar, now locate the two sides of the net and in particular the corner. Place the corner of
the net over the top corner of the goal, use a net hook on each side of the corner to secure.
Repeat this with all corners and finally evenly space net hooks around the goal.
FITTING THE NET:
10. PEGGING DOWN: Position the goal where it is to be used and drive the U-Pegs (19
PEG-020) into the ground over the side bar (See Diagram above). If the goal is not for grass
use, please see note on the first page on synthetic anchor options.