Harrod VOL-033 User manual

VOL-033 - SITTING VOLLEYBALL (BOLT DOWN)
VOL-033 & 034
SITTING VOLLEYBALL POST (BOLT DOWN OR SELF WEIGHTED) Harrod UK Limited
1: Make sure you read the Instructions before assembling the product. Then unpack and check you have
the correct amount of parts as per instructions.
INS333
Revison 0
20/05/2014
PAGE 1
VOL-034 - SITTING VOLLEYBALL (SELF WEIGHTED)
Note: Weights Not Sold with this product
Code:
Product:
Code:
Product:
Code:
Product:
Code:
Product: ©
WEIGHTS
NOT SUPPLIED

VOL-033 & 034
SITTING VOLLEYBALL POST (BOLT DOWN OR SELF WEIGHTED)
Code:
Product:
Code:
Product:
Code:
Product:
Code:
Product:
MAKE SURE YOU READ THESE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING YOUR POSTS
Floor Socket Installation
All sockets should be installed by a specialist, using the following guidelines.
Please contact your distributor for recommended specialist fitting engineers.
Mark at location shown below. Drill Ø20 holes to the depth to suite purchased sockets.
are 8351mm (8.351m)
(NOTE: 8300mm (8.3m) is Harrod Suggested hole Centres,
this can range between 8300mm (8.3m) to 9300mm (9.3m)
are 8511mm x 400mm (8.511m x 0.4m).
(NOTE: 8500mm (8.5m) is Harrod Suggested hole Centres,
this can range between 8500mm (8.5m) to 9500mm (9.5m)
Note: Longer Sockets are required for sprung floors. (Contact your distributor for guidance).
2 Point Socket Centres
4 Point Socket centres
Floor sockets are not included and should be ordered separately.
Solid Floors required 2 off SHP-001 - (or 4 if using rear fixing points)
Suspended Floors require 2 off SHP-100 - (or 4 if using rear fixing points)
500mm 500mm
6500mm
6000mm (6m) Outer Sidelines of Court
7500mm (7.5m) To Front of Posts
500mm to
1000mm
500mm to
1000mm
400mm (0.4m)
Hole Centres
8686mm (8.686m) Outside of Posts
8511mm (8.511m) - 4 Hole Socket Centre
8351mm (8.351m) - 2 Hole Socket Centre
FOUR HOLE CENTRE INSTALLATIONS GUIDE
TWO HOLE CENTRE INSTALLATION GUIDE
Net Not Included
PAGE 2

FEP207
Sitting Volleyball Dummy Post
FEP206
Sitting Volleyball Winder Post
FEP241
Sitting Volleyball Base Assembly
including fittings FPK033
X1
FPK033
Sitting Volleyball Fittings Pack
PEP205 x4
(Bolt down use
only)
CAP950
x8 BOL205
x4
X1
X1
PEP205
x4
BOL300
x4
BOL202
x8
BOL530
x4
BOL337
x4
PAGE 3
FPK034
Sitting Volleyball Fittings Pack
FEP030
Sitting Volleyball Self Weighted Assembly
Frame & including fittings FPK034
BOL709
x4
BOL712
x8
X1
VOL-033 x1
VOL-034 x1
Code:
Product:
Code:
Product:
Code:
Product:
Code:
Product: SITTING VOLLEYBALL POST (BOLT DOWN OR SELF WEIGHTED) Harrod UK Limited
VOL-033 & 034
©©©©©©©©©
VOL-033 x1
VOL-034 x1
VOL-034 ONLY - SELF WEIGHTED

2: Unscrew the bolts from the back of either FEP206 or FEP207
then slide one FEP241 to the upright & locate on the square
head bolts in the upright. Fasten into place with the washer
and nylock. Place a nut cap over the nylock on done.
3: Note: for Self Weighted post, jump straight to page 4.
Slide the square headed bolt and the aluminium
square space along the channel. Connect the
back stay to square headed bolt and the bolt on
the back of the base, tighten up into place using
nylock nut and place nut cap on to finish off.
5: Screw the T-bolt in the nuts
on the top of the base when
not in use.
4: Repeat the above process for the other
upright post & base
6: Place the uprights on the court where required
and bolt down into place using the t-bolts,
either the back two bolt holes or the single
single central hole.
PAGE 4
Code:
Product:
Code:
Product:
Code:
Product:
Code:
Product: SITTING VOLLEYBALL POST (BOLT DOWN OR SELF WEIGHTED)
VOL-033 & 034
Harrod UK Limited
©

1: The back stanchion is not required. Remove
from upright and base if you have standard
volleyball set and required to add the self
weighted frame. If you have purchased VOL-034
refer to steps1&2onpage 3 for setting up posts.
BOL300
X2
BOL712 X4
BOL202 X2
CAP950 X4
FEP030
FEP030
2: Assemble the self weighted support frame by aligning
the 2 bolt holes up and inserting BOL300 & BOL712.
Then Secure into place with BOL712 and BOL202. Once you
have done that place CAP950 over BOL202 & BOL300.
CAP950 x1
BOL337 x1
BOL712 x1
3: Gently Remove the caps from the base.
4: Sit the frame onto the base as shown right,
so that the square headed bolt is in the bolt
hole of the brace.
5: Using the bolts from the fittings pack
secure the rest of the into place. Once all
tightened up add the nut cap & tap in the
caps into the base to finish off.
Remove
the cap
from ends
BOL709 x1
BOL202 x1
PAGE 5
Code:
Product:
Code:
Product:
Code:
Product:
Code:
Product: SITTING VOLLEYBALL POST (BOLT DOWN OR SELF WEIGHTED)
VOL-033 & 034
Harrod UK Limited
©©©©
VOL-034 - Self Weighted Version Only

VOL-033 & 034
SITTING VOLLEYBALL POST (BOLT DOWN OR SELF WEIGHTED)
WINDER POST
DUMMY POST
SITTING VOLLEYBALL NET
6.5m x 0.8m
1: Feed the head line rope over the roller on the Dummy Post
and connect to the below the bottom eyelet.
2: Feed the headline rope over the roller on the Winder Pos
and connect to winch strap carbine clip.
3: Connect the side ropes to the eyelets on the Dummy &
Winder post to keep the side of the net straight once the
net is tensioned up to the correct height.
Harrod UK Limited©
Code:
Product:
PAGE 6
VOL-031 - (Supplied Separately)